Short-term heating tests on doped polypyrrole-coated polyester fabrics

Polyethyleneterephtalate–polypyrrole (PET–PPy) textile complexes incorporating different anionic dopants have been heat treated at 60 °C, 80 °C, 105 °C, 125 °C and 150 °C to investigate effects of short-term heating on conductivity and stability. In most cases heat treatments below 80 °C did not significantly change the final resistance of the conducting textiles. Only the anionic dye-dopant Indigo Carmine acted in a heat-stabilizing manner during treatment at 150 °C, while all samples containing other anionic dopant underwent some degradation. A treatment temperature of 125 °C was the most effective for lowering the final resistance, with sulphonic group containing dopants being particularly effective in improving conductivity and stability. A 29% decrease in the final resistance of a PET–PPy/para-toluene-2-sulphonic acid (pTSA) sample was achievable after 900 s at 125 °C.

Effect of single and double austenitization treatments on the microstructure and hardness of AISI D2 tool steel

This investigation is concerned with the study of effect of Double Austenitization (DA) and Single Austenitization (SA) heat treatment processes on microstructure and mechanical property of AISI D2type cold worked tool steel. To maximize hardness, tool steels are used in a quenched and tempered condition. This involves heating the material to the austenitizing temperature (~850-1100. °C), quenching at an appropriate rate to form martensite, and tempering to reduce the retained austenite content and induce toughness. The merits of DA treatment isto promote dissolution of carbides at the same time proscribe grain coarsening significantly was attempted in D2 tool steel. The study has found that DA treatment has induced high hardness with insignificant growth in grains. The increase in hardness is attributed to increase in carbon content in matrix due to dissolution of carbides; whereas finer grains due to role of inclusions.

What are we scared of? The absence of sociology in current debates about drug treatments and policies

The official public policy related to recreational drug use and abuse in Australia is harm minimization or harm reduction. Definitions of harm minimization vary but a general statement is that harm minimization is a policy or programme intended to decrease adverse health, social and economic consequences of drug use, even though the user may continue to use psychoactive drugs. This type of definition is most often compared to a zero-tolerance policy that aims to eliminate all recreational drug abuse by legal and other means. Sociologists have historically scoffed at this latter policy. Unfortunately, what this has meant is that harm minimization in all its forms has not been the object of analytical work on the part of sociologists.

The influence of demographic, behavioural and treatments characteristics on problem gambling counselling outcomes

The paper considers the influence of client characteristics and gambling behaviour as well as treatment modality on the resolution of gambling behaviour for 591 clients who sought help from the publicly funded BreakEven counselling services in the state of Victoria between 1 July 1996 and 30 June 1997. Statistical data about clients and their consultations was collected in the form of a Minimum Data Set. On their own, client demographics accounting for 12% of the variance were identified as discriminating between problem gamblers who achieved some resolution of their gambling behaviour and those whose behaviour did not change. Variables associated with gambling behaviour accounted for 10% of variance and treatment variables for 12% of variance in treatment outcomes. Collectively, the three types of data could explain 26% of the variance in problem resolution. Importantly, these findings demonstrate that the resolution of problematic gambling behaviour is affected by a complex interplay of client characteristics, their gambling behaviour and the treatment they receive. It is argued that the evaluation of treatment programs for problem gambling, and potentially all counselling programs in the primary health arena, needs to include measures from each of these domains.

Conductive fabrics for heating applications

By coating textiles with electrically conductive organic polymers, we are able to produce functional, intelligent fabrics. These fabrics can be utilised in applications such as gas sensors, actuators, electromagnetic shielding, radar absorption, selected frequency filtering in indoor wireless applications, and heating applications where vital parts of the body can be heated without embedding any wiring through the fabric.

Heat generation in fabrics coated with the conductive polymer polypyrrole was investigated. The fabrics were coated by chemical synthesis methods by oxidizing the pyrrole monomer in the presence of the fabric substrate. Ferric chloride was selected as the oxidizing agent and anthraquinone-2-sulfonic acid (AQSA) sodium salt monohydrate as the dopant.

Conductive fabrics were characterized by resistivity measurements, scanning electron microscopy, thermal imaging, current transmission over a period of time and calculations of power density per unit area. Effects of reaction conditions on the electrical properties and heat generated are presented. Polypyrrole coated fabrics were stable and possessed high electrical conductivity. Resistivity values ranged from 100-500 ohms/square depending on the reaction parameters. When subjected to a constant voltage of 24V, the polypyrrole coated polyester-Lycra® fabric doped with AQSA reached a maximum temperature of 42°C and a power density per unit area of 430 W/m² was achieved.

Computational simulation of heat transfer from alternate heating sources

The alternant heat transfer induced by particle packet and gas bubbles on an object surface in a gas fluidised bed is computationally studied. The particle packet and bubble are modelled by a DPPM (double particle-layer and Porous Medium) model and a hemispherical model, respectively. Different meshing schemes are applied and different mesh sizes are used in meshing particle packet and heated object and a very large geometrical size difference between them was considered. Two parallel solver processes were proposed to perform the simulation of heat transfer for different purposes and implemented with the Fluent CFD package.

Solar heating systems for recirculation aquaculture

The literature over the past 25 years indicates that there has been a continued interest in using passive and active solar technologies to reduce the conventional energy required to maintain water temperatures in small recirculation aquaculture systems. Although all of the experimental systems reviewed report favourable results, there is little information available to guide system designers. This paper describes the use of a simulation model to predict the annual conventional energy consumption of a 10.6 m3 RAS enclosed in a double layer polyethylene greenhouse in two different climates. The water was maintained at 22.5 °C and the recirculation rate was 10% of tank volume per day. Simple unglazed solar collectors have also been combined with the greenhouse to further reduce energy consumption. The effect of increasing collector area on the solar fraction and utilization of useful energy was predicted. Finally, the model was used to investigate the relationship between the occurrence of condensation on the inner cover, ventilation rates and energy use. It was found that in a hot dry climate, the greenhouse alone was sufficient to reduce the conventional energy requirements by 87%; while in the cooler temperate climate reductions of 66% were possible. When solar collectors were added to the system, conventional energy requirements were reduced further and depended on the area of collector used. For example, in the temperate climate location, conventional energy requirements were reduced to 23% of a RAS enclosed in a non-solar building when 26 m2 of solar collector inclined at the optimum angle for winter energy collection were used. Although condensation could be successfully reduced by ventilation of the greenhouse, this increased conventional energy requirements because the potential for evaporation was increased. Covering the tanks at night was found to be a more effective strategy because it reduced condensation and conventional energy use simultaneously.

The effect of cure cycle heating rate on the fibre/matrix interface

Development of civil aerospace composites is key to future “greener” aircraft. Aircraft manufacturers must improve efficiency of their product and manufacturing processes to remain viable. The aerospace industry is undergoing a materials revolution in the design and manufacture of composite airframes. The Airbus A350 and Boeing 787 (both due to enter service in the latter part of this decade) will push utilisation levels of  composite materials beyond 50% of the total airframe by weight. This  change requires massive investment in materials technology, manufacturing capability and skills development. The Quickstep process provides the ability to rapidly cure aerospace standard composite materials whilst providing enhanced mechanical properties. Utilising fluid to transfer heat to the   composite component during the curing process allows far higher heat rates than with conventional cure techniques. The rapid heat-up rates reduce the viscosity of the resin system greatly to provide a longer processing window introducing greater flexibility and removing the need for high pressure during cure. Interlaminar fracture toughness (Mode I) and Interfacial Shear Strength of aerospace standard materials cured using Quickstep have been    compared to autoclave cured laminates. Results suggest an improvement in fibre-matrix adhesion.

Heating effects on water repellency in Australian eucalypt forest soils and their value in estimating wildfire soil temperatures

Wildfires can induce or enhance soil water repellency under a range of vegetation communities. According to mainly USA-based laboratory studies, repellency is eliminated at a maximum soil temperature (T) of 280–400°C. Knowledge of T reached during a wildfire is important in evaluating post-fire soil physical properties, fertility and seedbed status. T is, however, notoriously difficult to ascertain retrospectively and often based on indicative observations with a large potential error. Soils under fire-prone Australian eucalypt forests tend to be water repellent when dry or moderately moist even if long unburnt. This study aims to quantify the temperature of water repellency destruction for Australian topsoil material sampled under three sites with contrasting eucalypt cover (Eucalyptus sieberi, E. ovata and E. baxteri). Soil water repellency was present prior to heating in all samples, increased during heating, but was abruptly eliminated at a specific T between 260 and 340°C. Elimination temperature varied somewhat between samples, but was found to be dependent on heating duration, with longest duration resulting in lowest elimination temperature. Results suggest that post-fire water repellency may be used as an aid in hindcasting soil temperature reached during the passage of a fire within repellency-prone environments.

Galling reduction through die surface treatment - testing three treatments for sheet metal stamping

This brief article describes how tool galling occurs in stamping and describes results of tests on how TiCN, Hard-Cr, and CrCN were used on sample parts to help reduce galling.