A novel crevice corrosion experiment using a wire beam electrode

This paper describes a new experiment for studying crevice corrosion. A wire beam electrode was employed in this experiment to measure electrochemical parameters directly from crevice area and these parameters were used to calculate instantaneous crevice corrosion kinetics. A clear correlation between calculated corrosion depth map and real corrosion appearance was obtained.

Continuous corrosion rate measurement by noise resistance calculation

A commonly employed method of corrosion rate measurement is to determine the electrochemical impedance of the corroding material. One technique for estimating the impedance is the noise impedance calculation. While it has been shown to yield useful results, there are a number of problems that require attention. This paper identifies some of those problems-specifically, those of detrending and resolution-and provides a solution that allows continuous, time-varying noise resistance and noise impedance calculations to be performed with known time, frequency, and magnitude resolutions. Applications to synthetic and experimental data are included as illustrations

In situ measurement of pipeline coating integrity and corrosion resistance losses under simulated mechanical strains and cathodic protection

A novel experimental assembly consisting of a specially designed tensile testing rig and a standard electrochemical flat cell has been designed for simulating buried high pressure pipeline environmental conditions in which a coating gets damaged and degrades under mechanical strain, and for studying the influence of mechanically induced damages such as the cracking of a coating on its anti-corrosion property. The experimental assembly is also capable of applying a cathodic protection (CP) potential simultaneously with the mechanical strain and environmental exposure. The influence of applied mechanical strain as well as extended exposure to the corrosive environment, coupled with the application of CP, has been investigated based on changes in electrochemical impedance spectroscopy (EIS). Preliminary results show that the amplitude of the coating impedance decreases with an increase in the applied strain level and the length of environmental exposure. The EIS characteristics and changes are found to correlate well with variations in coating cracking and degradation features observed on post-test samples using both optical microscopy and scanning electron microscopy. These results demonstrate that this new experimental method can be used to simulate and examine coating behaviour under the effects of complex high pressure pipeline mechanical, electrochemical and environmental conditions.

Electrochemical impedance spectroscopy and surface characterization techniques to study carbon dioxide corrosion product scales

Electrochemical impedance spectroscopy (EIS) was used to study carbon dioxide (CO2) corrosion product scales and their effects on further CO2 corrosion. Objectives were to determine the suitability of EIS for studying corrosion scales and to investigate the influence of environmental factors on scale formation. EIS provided useful information about protective abilities and electrochemical properties of corrosion scales. CO2 corrosion scales formed at high-temperature and pressure provided better protection than those formed at low-temperature and pressure. The level of protection of the scale formed at higher temperature and pressure increased with exposure time. EIS results were compared with coupon weight-loss measurements. Scales were analyzed using a combination of Fourier transform infrared (FTIR) analysis, x-ray diffraction (XRD), and electron microscopy.

Wire beam electrode : a new tool for studying localised corrosion and other heterogeneous electrochemical processes

Heterogeneous electrochemical processes are very common in industry and are important, but difficult topics in electrochemical and corrosion science studies. Traditional electrochemical techniques which employ a conventional one-piece electrode have major limitations in studying heterogeneous electrochemical processes since the one-piece electrode has major difficulties in measuring electrochemical parameters from local areas of the electrode surface. In order to overcome this problem, a multi-piece electrode, namely the wire beam electrode, has been developed. This new electrode enables the measurement of electrochemical parameters from local areas over a working electrode surface and thus it can be used to study heterogeneous electrochemical processes. This paper describes how this new electrode was applied in studying several typical heterogeneous electrochemical processes including water-drop corrosion, corrosion under non-uniform organic films and cathodic protection.

Studies of CO2 corrosion product scales using electrochemical impedance spectroscopy and surface characterisation techniques

Electrochemical impedance spectroscopy (EIS) was used to study carbon dioxide (CO2) corrosion product scales and their effects on further CO2 corrosion. Objectives were to determine the suitability of EIS for studying corrosion scales and to investigate the influence of environmental factors on scale formation. EIS provided useful information about protective abilities and electrochemical properties of corrosion scales. CO2 corrosion scales formed at high-temperature and pressure provided better protection than those formed at low-temperature and pressure. The level of protection of the scale formed at higher temperature and pressure increased with exposure time. EIS results were compared with coupon weight-loss measurements. Scales were analyzed using a combination of Fourier transform infrared (FTIR) analysis, x-ray diffraction (XRD), and electron microscopy

Quantifying the efficiency and understanding the mechanism of localised corrosion inhibition using the wire beam electrode

Parameters extracted from the wire beam electrode (WBE) galvanic current maps have been used in conjunction with electrochemical noise patterns to directly quantify the degree of localised corrosion inhibition provided by inhibitors and to understand the mechanism of localised corrosion inhibition. The behaviour of two traditional localised corrosion inhibitors has been assessed by their effects on the maximum anodic current density (imax), total anodic current density (itot), the number of anodic sites (Na) and the localised corrosion intensity index (LCII). Typical experiments are presented to illustrate the application of these parameters in providing useful information on the efficiency and mechanism of localised corrosion inhibition.