Txtng as a replacement for standard written English : an attitude survey based on Age and Gender

Text messaging is a new form of writing, brought about by technological development in the last couple of decades. Mobile phone usage has increased rapidly worldwide and texting is now part of many people's everyday communcation. A large number of users send or receive texts which include some abbreviations and shortenings, commonly referred to as textspeak. This novel linguistic phenomenon is perceived by some with indifference and by others with aggravation. The following study examines attitudes towards this linguistic change from a gender and age perspective. The comparison between two groups show that the most conservative and least positive to change are young women. The analysis and discussion around this focuses on power, prestige and patterns.

Hesitations and repair in German

The occurrence of pauses and hesitations in spontaneous speech has been shown to occur systematically, for example, "between sentences, after discourse markers and conjunctions and before accented content words." (Hansson [15]) This is certainly plausible in English, where pauses and hesitations can and often do occur before content words such as nominals, for example, "uh, there's a … man." (Chafe [8]) However, if hesitations are, in fact, evidence of "deciding what to talk about next," (Chafe [8]) then the complex grammatical system of German should render this pausing position precarious, since pre-modifiers must account for the gender of the nominals they modify.In this paper, I present data to test the hypothesis that pre-nominal hesitation patterns in German are dissimilar to those in English. Hesitations in German will be shown, in fact, to occur within noun phrase units. Nevertheless, native speakers most often succeed in supplying a nominal which conforms to the gender indicated by the determiner or pre-modifier. Corrections, or repairs, of infelicitous pre-modifiers indicate that the speaker was unable to supply a nominal of the same gender which the choice of pre-modifier had committed him/her to. The frequency of such repairs is shown to vary according to task, with fewest repairs occurring in elicited speech which allows for linguistic freedom and therefore is most like spontaneous speech. The data sets indicate that among German native speakers, hesitations occurring before noun phrase units (pre-NPU hesitations) indicate deliberation of what to say, while hesitations within or before the head of the noun phrase (pre-NPH hesitations) indicate deliberation of how to say what has already been decided (cf. Chafe [8]).

Improved Road Design for Future Maintenance - Analysis of Road Barrier Repair Costs

The cost of a road construction over its service life is a function of the design, quality of construction, maintenance strategies and maintenance operations. Unfortunately, designers often neglect a very important aspect which is the possibility to perform future maintenance activities. The focus is mainly on other aspects such as investment costs, traffic safety, aesthetic appearance, regional development and environmental effects. This licentiate thesis is a part of a Ph.D. project entitled “Road Design for lower maintenance costs” that aims to examine how the life-cycle costs can be optimized by selection of appropriate geometrical designs for the roads and their components. The result is expected to give a basis for a new method used in the road planning and design process using life-cycle cost analysis with particular emphasis on road maintenance. The project started with a review of literature with the intention to study conditions causing increased needs for road maintenance, the efforts made by the road authorities to satisfy those needs and the improvement potential by consideration of maintenance aspects during planning and design. An investigation was carried out to identify the problems which obstruct due consideration of maintenance aspects during the road planning and design process. This investigation focused mainly on the road planning and design process at the Swedish Road Administration. However, the road planning and design process in Denmark, Finland and Norway were also roughly evaluated to gain a broader knowledge about the research subject. The investigation was carried out in two phases: data collection and data analysis. Data was collected by semi-structured interviews with expert actors involved in planning, design and maintenance and by a review of design-related documents. Data analyses were carried out using a method called “Change Analysis”. This investigation revealed a complex combination of problems which result in inadequate consideration of maintenance aspects. Several urgent needs for changes to eliminate these problems were identified. Another study was carried out to develop a model for calculation of the repair costs for damages of different road barrier types and to analyse how factors such as road type, speed limits, barrier types, barrier placement, type of road section, alignment and seasonal effects affect the barrier damages and the associated repair costs. This study was carried out using a method called the “Case Study Research Method”. Data was collected from 1087 barrier repairs in two regional offices of the Swedish Road Administration, the Central Region and the Western Region. A table was established for both regions containing the repair cost per vehicle kilometre for different combinations of barrier types, road types and speed limits. This table can be used by the designers in the calculation of the life-cycle costs for different road barrier types.

Product verification and defect repair - status and considerations

Product verifications have become a cost-intensive and time-consuming aspect of modern electronics production, but with the onset of an ever-increasing miniaturisation, these aspects will become even more cumbersome. One may also go as far as to point out that certain precision assembly, such as within the biomedical sector, is legally bound to have 0 defects within production. Since miniaturisation and precision assembly will soon become a part of almost any product, the verifications phases of assembly need to be optimised in both functionality and cost. Another aspect relates to the stability and robustness of processes, a pre-requisite for flexibility. Furthermore, as the re-engineering cycle becomes ever more important, all information gathered within the ongoing process becomes vital. In view of these points, product, or process verification may be assumed to be an important and integral part of precision assembly. In this paper, product verification is defined as the process of determining whether or not the products, at a given phase in the life-cycle, fulfil the established specifications. Since the product is given its final form and function in the assembly, the product verification normally takes place somewhere in the assembly line which is the focus for this paper.