Module property verification : A method to plan and perform quality verifications in modular architectures

Modular product architectures have generated numerous benefits for companies in terms of cost, lead-time and quality. The defined interfaces and the module’s properties decrease the effort to develop new product variants, and provide an opportunity to perform parallel tasks in design, manufacturing and assembly. The background of this thesis is that companies perform verifications (tests, inspections and controls) of products late, when most of the parts have been assembled. This extends the lead-time to delivery and ruins benefits from a modular product architecture; specifically when the verifications are extensive and the frequency of detected defects is high. Due to the number of product variants obtained from the modular product architecture, verifications must handle a wide range of equipment, instructions and goal values to ensure that high quality products can be delivered. As a result, the total benefits from a modular product architecture are difficult to achieve. This thesis describes a method for planning and performing verifications within a modular product architecture. The method supports companies by utilizing the defined modules for verifications already at module level, so called MPV (Module Property Verification). With MPV, defects are detected at an earlier point, compared to verification of a complete product, and the number of verifications is decreased. The MPV method is built up of three phases. In Phase A, candidate modules are evaluated on the basis of costs and lead-time of the verifications and the repair of defects. An MPV-index is obtained which quantifies the module and indicates if the module should be verified at product level or by MPV. In Phase B, the interface interaction between the modules is evaluated, as well as the distribution of properties among the modules. The purpose is to evaluate the extent to which supplementary verifications at product level is needed. Phase C supports a selection of the final verification strategy. The cost and lead-time for the supplementary verifications are considered together with the results from Phase A and B. The MPV method is based on a set of qualitative and quantitative measures and tools which provide an overview and support the achievement of cost and time efficient company specific verifications. A practical application in industry shows how the MPV method can be used, and the subsequent benefits

Entry, re-location and growth in the Swedish wholesale trade industry

Wholesale trade has an intermediate position between manufacturing and retail in the distributional channel. In modern economies, consumers buy few, if any, products directly from manufacture or producer. Instead, it is a wholesaler, who is in direct contact with producers, buying goods in larger quantities and selling them in smaller quantities to retailers. Traditionally, the main function of a wholesaler has been to push goods along the distributional channel from producer to retailer, or other nonend user. However, the function of wholesalers usually goes beyond the process of the physical distribution of goods. Wholesalers also arrange storage, perform market analyses, promote trade or provide technical support to consumers (Riemers 1998). The existence of wholesalers (and other intermediaries) in the distributional channel is based on the effective and efficient performance of distribution services, that are needed by producers and other members of the supply chain. Producers usually do not enjoy the economies of scale that they have in production, when it comes to providing distributional services (Rosenbloom 2007) and this creates a space for wholesalers or other intermediaries. Even though recent developments in the distributional channel indicate that traditional wholesaling activities now also compete with other supply chain organizations, wholesaling still remains an important activity in many economies (Quinn and Sparks, 2007). In 2010, the Swedish wholesale trade sector consisted of approximately 46.000 firms and generated an annual turnover of 1 300 billion SEK (Företagsstatistiken, Statistics Sweden). In terms of turnover, wholesaling accounts for 20% of the gross domestic product and is thereby the third largest industry. This is behind manufacturing and a composite group of firms in other sectors of the service industry but ahead of retailing. This indicates that the wholesale trade sector is an important part of the Swedish economy. The position of wholesaling is further reinforced when measuring productivity growth. Measured in terms of value added per employee, wholesaling experienced the largest productivity growth of all industries in the Swedish economy during the years 2000 through 2010. The fact that wholesale trade is one of the important parts of a modern economy, and the positive development of the Swedish wholesale trade sector in recent decades, leads to several questions related to industry dynamics. The three topics that will be examined in this thesis are firm entry, firm relocation and firm growth. The main question to be answered by this thesis is what factors influence new firm formation, firm relocation and firm growth in the Swedish wholesale trade sector?

Proceedings from the 2nd seminar on Development of Modular Products : December 13-14, 2004, Campus Framtidsdalen, Dalarna University, Sweden

Companies are focusing on efforts increasing the overall efficiency at the same time as the ability to meet customer needs becomes even more important. There is a need to improve the organisation and the product design at the same time through the visualisation of how a product family design should be performed in order to adapt to customers, company internal issues, and long-term strategy. Therefore, there is a need for qualified personnel in today’s companies with the knowledge of product development and modularity. The graduate course Development of Modular Products at Högskolan Dalarna has the objective to provide such knowledge. As a part of the course, each student will individually perform extensive research within a chosen area with respect to Product Development and Modularity. This proceeding is the result of the students own work and was presented during a two day seminar at Dalarna University. The contents of the papers cover many areas, from the identification of customer needs to cost effective manufacturing, and benefits of modularisation. The reader of this proceeding will not only benefit from many areas within Product Development and Modularity but also from the colour of many cultures. In this proceeding, students from nine countries are represented (Bangladesh, China, Costa Rica, Germany, Holland, India, Luxembourg Nigeria, and Sweden). Enjoy the reading.

Cloud computing - Moving to the cloud

Cloud computing innebär användning av datorresurser som är tillgängliga via ett nätverk, oftast Internet och är ett område som har vuxit fram i snabb takt under de senaste åren. Allt fler företag migrerar hela eller delar av sin verksamhet till molnet. Sogeti i Borlänge har behov av att migrera sina utvecklingsmiljöer till en molntjänst då drift och underhåll av dessa är kostsamma och tidsödande. Som Microsoftpartners vill Sogeti använda Microsoft tjänst för cloud computing, Windows Azure, för detta syfte. Migration till molnet är ett nytt område för Sogeti och de har inga beskrivningar för hur en sådan process går till. Vårt uppdrag var att utveckla ett tillvägagångssätt för migration av en IT-lösning till molnet. En del av uppdraget blev då att kartlägga cloud computing, dess beståndsdelar samt vilka för- och nackdelar som finns, vilket har gjort att vi har fått grundläggande kunskap i ämnet. För att utveckla ett tillvägagångssätt för migration har vi utfört flera migrationer av virtuella maskiner till Windows Azure och utifrån dessa migrationer, litteraturstudier och intervjuer dragit slutsatser som mynnat ut i ett generellt tillvägagångssätt för migration till molnet. Resultatet har visat att det är svårt att göra en generell men samtidigt detaljerad beskrivning över ett tillvägagångssätt för migration, då scenariot ser olika ut beroende på vad som ska migreras och vilken typ av molntjänst som används. Vi har dock utifrån våra erfarenheter från våra migrationer, tillsammans med litteraturstudier, dokumentstudier och intervjuer lyft vår kunskap till en generell nivå. Från denna kunskap har vi sammanställt ett generellt tillvägagångssätt med större fokus på de förberedande aktiviteter som en organisation bör genomföra innan migration. Våra studier har även resulterat i en fördjupad beskrivning av cloud computing. I vår studie har vi inte sett att någon tidigare har beskrivit kritiska framgångsfaktorer i samband med cloud computing. I vårt empiriska arbete har vi dock identifierat tre kritiska framgångsfaktorer för cloud computing och i och med detta täckt upp en del av kunskapsgapet där emellan.

‘Being in a womb’ or ‘playing musical chairs’ : the impact of place and space on infant feeding in NICUs

Background: Becoming a parent of a preterm baby requiring neonatal care constitutes an extraordinary life situation in which parenting begins and evolves in a medical and unfamiliar setting. Although there is increasing emphasis within maternity and neonatal care on the influence of place and space upon the experiences of staff and service users, there is a lack of research on how space and place influence relationships and care in the neonatal environment. The aim of this study was to explore, in-depth, the impact of place and space on parents’ experiences and practices related to feeding their preterm babies in Neonatal Intensive Care Units (NICUs) in Sweden and England. Methods: An ethnographic approach was utilised in two NICUs in Sweden and two comparable units in England, UK. Over an eleven month period, a total of 52 mothers, 19 fathers and 102 staff were observed and interviewed. A grounded theory approach was utilised throughout data collection and analysis. Results: The core category of ‘the room as a conveyance for an attuned feeding’ was underpinned by four categories: the level of ‘ownership’ of space and place; the feeling of ‘at-homeness’; the experience of ‘the door or a shield’ against people entering, for privacy, for enabling a focus within, and for regulating socialising and the; ‘window of opportunity’. Findings showed that the construction and design of space and place was strongly influential on the developing parent-infant relationship and for experiencing a sense of connectedness and a shared awareness with the baby during feeding, an attuned feeding. Conclusions: If our proposed model is valid, it is vital that these findings are considered when developing or reconfiguring NICUs so that account is taken of the influences of spatiality upon parent’s experiences. Even without redesign there are measures that may be taken to make a positive difference for parents and their preterm babies.

Simplified follow-up after medical abortion using a low-sensitivity urinary pregnancy test and a pictorial instruction sheet in Rajasthan, India : study protocol and intervention adaptation of a randomised control trial

The World Health Organisation suggests that simplification of the medical abortion regime will contribute to an increased acceptability of medical abortion, among women as well as providers. It is expected that a home-based follow-up after a medical abortion will increase the willingness to opt for medical abortion as well as decrease the workload and service costs in the clinic. Trial design The study is a randomised, controlled, non-superiority trial . Methods Women screened to participate in the study are those with unwanted pregnancies and gestational ages equal to or less than nine weeks. Eligible women randomised to the home-based assessment group will use a low-sensitivity pregnancy test and a pictorial instruction sheet at home, while the women in the clinic follow-up group will return to the clinic for routine follow-up carried out by a doctor. The primary objective of the study is to evaluate the effectiveness of home-based assessment using a low-sensitivity pregnancy test and a pictorial instruction sheet 10-14 days after an early medical abortion. Providers or research assistants will not be blinded during outcome assessment. To ensure feasibility of the self-assessment intervention an adaption phase took place at the selected study sites before study initiation. This was to optimise and tailor-make the intervention and the study procedures and resulted in the development of the pictorial instruction sheet for how to use the low-sensitivity pregnancy test and the danger signs after a medical abortion. Discussion In this paper, we will describe the study protocol for a randomised control trial investigating the efficacy of simplified follow-up in terms of home-based assessment, 10-14 days after a medical abortion. Moreover, a description of the adaptation phase is included for a better understanding of the implementation of the intervention in a setting where literacy is low and the road-connections are poor. Trial registration: Clinicaltrials.gov NCT01827995. Registered 04 May 2013

How initial vocational education and training (IVET) teachers in Sweden perceive their prospects of being able to prepare upper secondary school pupils for a future occupation

Vocational teachers in Swedish upper secondary schools are a heterogeneous category of teachers, connected to different types of trade. These teachers represent a broad set of trade skills varying in content and character. In their teacher role, they continue to wear the clothes, speak the language, share the culture and remain mentally in their former professions. Still, it is central that they keep up this contact to be able to school the pupils into the environment of the trade in question, but also to help them to understand what skills a profession demands. However, the individual teacher also has to distance himself from the negative elements in the culture of the profession: patterns and habits that, for various reasons, have to be broken or changed. This paper draws attention to the ways in which a group of vocational teachers, who were participants in a project that aimed to train unauthorized vocational teachers, expressed their ambitions to prepare the pupils for a future professional career. When collecting information, we used the degree dissertations they produced and discussed in seminars, and informal dialogues. The result shows that it is important that the instruction location resembles a real working site as far as possible. These places are more or less realistic copies of a garage, a restaurant kitchen, a hairdressing salon, and so on, in order to give the pupils a realistic setting for instruction. However, the fact that these simulated workplaces lack the necessary support functions that exist in a company creates problems, problems which make a lot of extra work for the teachers. Vocational teachers also have to instruct the pupil in the experienced practitioner’s professional skills and working situation, but the pupil herself/himself must learn the job by doing it in practice. Some vocational upper secondary programs lack relevant course literature and the businesses give little support. This also makes extra work for the teachers. Moreover, the distance between the vocational programs and the trainee jobs was experienced as being difficult to overcome. One reason seems to be differences between businesses and differing preconditions between small and big companies’ abilities to take care of these pupils. The upper secondary school vocational programs also play a role in cementing existing gender roles, as well as perpetuating class-related patterns on the labour market.

How initial vocational education and training (IVET) teachers in Sweden perceive their prospects of being able to prepare upper secondary school pupils for a future occupation

Vocational teachers in Swedish upper secondary schools are a heterogeneous category of teachers, connected to different types of trade. These teachers represent a broad set of trade skills varying in content and character. In their teacher role, they continue to wear the clothes, speak the language, share the culture and remain mentally in their former professions. Still, it is central that they keep up this contact to be able to school the pupils into the environment of the trade in question, but also to help them to understand what skills a profession demands. However, the individual teacher also has to distance himself from the negative elements in the culture of the profession: patterns and habits that, for various reasons, have to be broken or changed. This paper draws attention to the ways in which a group of vocational teachers, who were participants in a project that aimed to train unauthorized vocational teachers, expressed their ambitions to prepare the pupils for a future professional career. When collecting information, we used the degree dissertations they produced and discussed in seminars, and informal dialogues. The result shows that it is important that the instruction location resembles a real working site as far as possible. These places are more or less realistic copies of a garage, a restaurant kitchen, a hairdressing salon, and so on, in order to give the pupils a realistic setting for instruction. However, the fact that these simulated workplaces lack the necessary support functions that exist in a company creates problems, problems which make a lot of extra work for the teachers. Vocational teachers also have to instruct the pupil in the experienced practitioner’s professional skills and working situation, but the pupil herself/himself must learn the job by doing it in practice. Some vocational upper secondary programs lack relevant course literature and the businesses give little support. This also makes extra work for the teachers. Moreover, the distance between the vocational programs and the trainee jobs was experienced as being difficult to overcome. One reason seems to be differences between businesses and differing preconditions between small and big companies’ abilities to take care of these pupils. The upper secondary school vocational programs also play a role in cementing existing gender roles, as well as perpetuating class-related patterns on the labour market.

Design and validation of a sheet metal shearing experimental procedure

Throughout the industrial processes of sheet metal manufacturing and refining, shear cutting is widely used for its speed and cost advantages over competing cutting methods. Industrial shears may include some force measurement possibilities, but the force is most likely influenced by friction losses between shear tool and the point of measurement, and are in general not showing the actual force applied to the sheet. Well defined shears and accurate measurements of force and shear tool position are important for understanding the influence of shear parameters. Accurate experimental data are also necessary for calibration of numerical shear models. Here, a dedicated laboratory set-up with well defined geometry and movement in the shear, and high measurability in terms of force and geometry is designed, built and verified. Parameters important to the shear process are studied with perturbation analysis techniques and requirements on input parameter accuracy are formulated to meet experimental output demands. Input parameters in shearing are mostly geometric parameters, but also material properties and contact conditions. Based on the accuracy requirements, a symmetric experiment with internal balancing of forces is constructed to avoid guides and corresponding friction losses. Finally, the experimental procedure is validated through shearing of a medium grade steel. With the obtained experimental set-up performance, force changes as result of changes in studied input parameters are distinguishable down to a level of 1%.

What determines the use of capital budgeting methods? : Evidence from Swedish listed companies

Purpose: This paper aims to extend and contribute to prior research on the association between company characteristics and choice of capital budgeting methods (CBMs). Design/methodology/approach: A multivariate regression analysis on questionnaire data from 2005 and 2008 is used to study which factors determine the choice of CBMs in Swedish listed companies. Findings: Our results supported hypotheses that Swedish listed companies have become more sophisticated over the years (or at least less unsophisticated) which indicates a closing of the theory-practice gap; that companies with greater leverage used payback more often; and that companies with stricter debt targets and less management ownership employed accounting rate of return more frequent. Moreover, larger companies used CBMs more often. Originality/value: The paper contributes to prior research within this field by being the first Swedish study to examine the association between use of CBMs and as many as twelve independent variables, including changes over time, by using multivariate regression analysis. The results are compared to a US and a continental European study.