Influence of grinding operations on surface integrity and chloride induced stress corrosion cracking of stainless steels

Stainless steels were developed in the early 20th century and are used where both the mechanical properties of steels and corrosion resistance are required. There is continuous research to allow stainless steel components to be produced in a more economical way and be used in more harsh environments. A necessary component in this effort is to correlate the service performance with the production processes. The central theme of this thesis is the mechanical grinding process.  This is commonly used for producing stainless steel components, and results in varied surface properties that will strongly affect their service life. The influence of grinding parameters including abrasive grit size, machine power and grinding lubricant were studied for 304L austenitic stainless steel (Paper II) and 2304 duplex stainless steel (Paper I). Surface integrity was proved to vary significantly with different grinding parameters. Abrasive grit size was found to have the largest influence. Surface defects (deep grooves, smearing, adhesive/cold welding chips and indentations), a highly deformed surface layer up to a few microns in thickness and the generation of high level tensile residual stresses in the surface layer along the grinding direction were observed as the main types of damage when grinding stainless steels. A large degree of residual stress anisotropy is interpreted as being due to mechanical effects dominating over thermal effects. The effect of grinding on stress corrosion cracking behaviour of 304L austenitic stainless steel in a chloride environment was also investigated (Paper III). Depending on the surface conditions, the actual loading by four-point bend was found to deviate from the calculated value using the formula according to ASTM G39 by different amounts. Grinding-induced surface tensile residual stress was suggested as the main factor to cause micro-cracks initiation on the ground surfaces. Grinding along the loading direction was proved to increase the susceptibility to chloride-induced SCC, while grinding perpendicular to the loading direction improved SCC resistance. The knowledge obtained from this work can provide a reference for choosing appropriate grinding parameters when fabricating stainless steel components; and can also be used to help understanding the failure mechanism of ground stainless steel components during service.

Värdefull litteratur : Fyra gymnasielärare om samhällsuppdragets etik i förhållande till litteraturen i klassrummet

The ethical aspects of the Swedish Curriculum for the non-compulsory school system, Lpf94, will form the basis of the research in this essay. The ethical aspects constitute fundamental values and goals as well as common tasks that must be carried out by every teacher. Since the school debate focuses a lot on this perspective, which is often mentioned together with the words problematic and contradictory, it will consequently also be the focus of this essay. Here these features are treated in relation to literature in all its forms used by teachers in class, which also represents a part of the school debate. Together ethics and literature form a perspective that lacks research. The goal is to investigate the ethical awareness of teachers in relation to the literature, and find out which ethical decisions are made by teachers and in what ways the ethical aspects of the curriculum is fulfilled. A qualitative method has been used in order to gain results: four upper secondary school teachers/senior high school teachers have been interviewed. The results are presented in interview transcripts which have been analyzed and interpreted in the light of recent studies and research and pedagogical-didactical literature. Accordingly I have been able to draw the conclusions that the ethical features in teaching is not explicit and that there seldom seems to be any conscious ethical reflections in relation to the literature. The ethical aspects are rather invisible and unconscious. However, it is clear that the interviews raise the awareness of the ethical perspective and thus emphasize the growing and developing function of the dialogue. Finally the results have been interpreted from the point of view of the ethical tasks of the teacher in order to make the ethics visible.I detta examensarbete ligger fokus på de etiska aspekterna av samhällsuppdraget i förhållande till den litteratur som lärare använder sig av i klassrumsundervisningen. Eftersom en stor del av skoldebatten handlar om samhällsuppdraget och dess värdegrund utgör också detta perspektiv utgångspunkten för denna undersökning. Målet är att undersöka vilka etiska avvägningar lärare gör i valet av litteratur och på vilket sätt samhällsuppdragets etik blir synlig i lärares arbete. Därmed framkommer också till viss del i vilken omfattning värdegrundsarbetet sker. Genom en kvalitativ undersökningsmetod i form av samtal har fyra gymnasielärare intervjuats. Erhållna resultat har presenterats i form av intervjutranskript som analyserats och tolkats med hjälp av aktuell forskning och pedagogisk-didaktisk litteratur. De slutsatser som kan dras utifrån resultaten är att etiken i lärarnas arbete inte är explicit och att det oftast inte finns en medveten etisk reflektion utifrån litteraturen. Etiken är snarare osynlig och tämligen omedveten. Dock medvetandegörs den under samtalen vilket framhåller dialogens betydelse för utveckling. Vidare framkommer att etiken aldrig är ett mål i sig, utan fungerar mer som medel för att nå andra mål i klassrummet. Slutligen, för att synliggöra etiken, har resultaten tolkats utifrån de etiska krav i samhällsuppdraget som ställs på lärare.

Module property verification : A method to plan and perform quality verifications in modular architectures

Modular product architectures have generated numerous benefits for companies in terms of cost, lead-time and quality. The defined interfaces and the module’s properties decrease the effort to develop new product variants, and provide an opportunity to perform parallel tasks in design, manufacturing and assembly. The background of this thesis is that companies perform verifications (tests, inspections and controls) of products late, when most of the parts have been assembled. This extends the lead-time to delivery and ruins benefits from a modular product architecture; specifically when the verifications are extensive and the frequency of detected defects is high. Due to the number of product variants obtained from the modular product architecture, verifications must handle a wide range of equipment, instructions and goal values to ensure that high quality products can be delivered. As a result, the total benefits from a modular product architecture are difficult to achieve. This thesis describes a method for planning and performing verifications within a modular product architecture. The method supports companies by utilizing the defined modules for verifications already at module level, so called MPV (Module Property Verification). With MPV, defects are detected at an earlier point, compared to verification of a complete product, and the number of verifications is decreased. The MPV method is built up of three phases. In Phase A, candidate modules are evaluated on the basis of costs and lead-time of the verifications and the repair of defects. An MPV-index is obtained which quantifies the module and indicates if the module should be verified at product level or by MPV. In Phase B, the interface interaction between the modules is evaluated, as well as the distribution of properties among the modules. The purpose is to evaluate the extent to which supplementary verifications at product level is needed. Phase C supports a selection of the final verification strategy. The cost and lead-time for the supplementary verifications are considered together with the results from Phase A and B. The MPV method is based on a set of qualitative and quantitative measures and tools which provide an overview and support the achievement of cost and time efficient company specific verifications. A practical application in industry shows how the MPV method can be used, and the subsequent benefits

Attraktiv expatriering : Före, under och efter

Syfte och utgångspunkt:    Att utifrån fyra organisationer undersöka faktorer som är viktiga för arbete med expatriering och att använda Mendenhall, Dunbar och Oddous modell som inspiration för att skapa en egen modell med faktorer värdefulla för en expatrieringsprocess.   Forskningsresan:                 Utifrån referensram samt ett empiriskt resultat av intervjuer identifieras fyra kategorier, betydelse av att ta med familjen, mentorskap och stöd, anpassning till kultur och karriärplanering. Det empiriska resultatet samt referensramen är sedan grunden till analys och slutsats.   Slutsats:                              I slutsatsen presenteras betydelsefulla faktorer för utgången av studiens syfte.   Dessa faktorer används sedan i den modell författarna skapat. Modellen visar hur behovet av de fyra kategorierna är beroende av den planerade utlandsstationeringens längd.   Metod:                                Författarna av studien utgår från en kvalitativ ansats med djupintervjuer som metod. Det empiriska resultatet baseras på det material som framkommit genom djupintervjuer med  respondenterna från de fyra organisationerna.

The Nurse Professional Competence (NPC) scale : self-reported competence among nursing students on the point of graduation

BACKGROUND: International organisations, e.g. WHO, stress the importance of competent registered nurses (RN) for the safety and quality of healthcare systems. Low competence among RNs has been shown to increase the morbidity and mortality of inpatients. OBJECTIVES: To investigate self-reported competence among nursing students on the point of graduation (NSPGs), using the Nurse Professional Competence (NPC) Scale, and to relate the findings to background factors. METHODS AND PARTICIPANTS: The NPC Scale consists of 88 items within eight competence areas (CAs) and two overarching themes. Questions about socio-economic background and perceived overall quality of the degree programme were added. In total, 1086 NSPGs (mean age, 28.1 [20-56]years, 87.3% women) from 11 universities/university colleges participated. RESULTS: NSPGs reported significantly higher scores for Theme I "Patient-Related Nursing" than for Theme II "Organisation and Development of Nursing Care". Younger NSPGs (20-27years) reported significantly higher scores for the CAs "Medical and Technical Care" and "Documentation and Information Technology". Female NSPGs scored significantly higher for "Value-Based Nursing". Those who had taken the nursing care programme at upper secondary school before the Bachelor of Science in Nursing (BSN) programme scored significantly higher on "Nursing Care", "Medical and Technical Care", "Teaching/Learning and Support", "Legislation in Nursing and Safety Planning" and on Theme I. Working extra paid hours in healthcare alongside the BSN programme contributed to significantly higher self-reported scores for four CAs and both themes. Clinical courses within the BSN programme contributed to perceived competence to a significantly higher degree than theoretical courses (93.2% vs 87.5% of NSPGs). SUMMARY AND CONCLUSION: Mean scores reported by NSPGs were highest for the four CAs connected with patient-related nursing and lowest for CAs relating to organisation and development of nursing care. We conclude that the NPC Scale can be used to identify and measure aspects of self-reported competence among NSPGs.