Koldiffusionens inverkan på utmattnings-hållfastheten hos varmvalsade sexkantsstänger;The influence of carbon diffusion on the fatigue strength of hot rolled hexagonal rods

Helstångsborr och konstång kallas bergborrverktyg, som tillverkas av sexkantiga stänger med inre hål för ledning av spolvatten. Dessa spolhål är klädda med ferritiskt rostfritt stål. Innan valsning borras ett centrerat hål i stålämnet som ska valsas. I det borrade hålet appliceras ett rör av ferritiskt rostfritt stål och i det röret skjuts en manganstålskärna in. Efter valsning dras kärnan ut och ett spolhål med invändigt foder av rostfritt stål bildas. Under uppvärmningen och valsningen av stålämnet sker normalt en koldiffusion från manganstålskärnan till det rostfria fodret. Fodrets syfte är att skydda spolhålets yta mot erosion och korrosion.Syftet med arbetet var att hitta en metod som garanterar uppkolning av det invändiga fodret, samt att utreda vad uppkolningen betyder för den mekaniska hållfastheten i stängerna. Ett laboratorieförsök visade att det var bra, med avseende på uppkolning, att blanda stearat i kärnbestrykningsmedlet. Kärnbestrykningsmedlet penslas på manganstålskärnan innan den förs in i stålämnet som ska valsas, dess syfte är att minska friktionen vid kärnutdragningen efter valsning.Ett försök utfördes i valsverket med stearat i kärnbestrykningsmedlet. En grundlig undersökning utfördes på två hetor som valsats med stearat-bestrykningsmedel, samt på en traditionellt tillverkad heta för att ha som referens. Hetorna kapades till provstänger om 1,5 m, totalt undersöktes 55 st.Utvärderingen av verksförsöket visade att stängernas kvalitet blir tillräckligt bra om ingenting oförutsett händer i produktionen, oavsett om koltillskott är tillsatt i bestrykningsmedlet eller inte. Arbetet gav inte en garanterande metod, men visade att stängerna normalt håller hög kvalitet.

Radiation properties of coil-coated steel in building envelope surfaces and the influence on building thermal performance

Recent studies have shown that the optical properties of building exterior surfaces are important in terms of energy use and thermal comfort. While the majority of the studies are related to exterior surfaces, the radiation properties of interior surfaces are less thoroughly investigated. Development in the coil-coating industries has now made it possible to allocate different optical properties for both exterior and interior surfaces of steel-clad buildings. The aim of this thesis is to investigate the influence of surface radiation properties with the focus on the thermal emittance of the interior surfaces, the modeling approaches and their consequences in the context of the building energy performance and indoor thermal environment. The study consists of both numerical and experimental investigations. The experimental investigations include parallel field measurements on three similar test cabins with different interior and exterior surface radiation properties in Borlänge, Sweden, and two ice rink arenas with normal and low emissive ceiling in Luleå, Sweden. The numerical methods include comparative simulations by the use of dynamic heat flux models, Building Energy Simulation (BES), Computational Fluid Dynamics (CFD) and a coupled model for BES and CFD. Several parametric studies and thermal performance analyses were carried out in combination with the different numerical methods. The parallel field measurements on the test cabins include the air, surface and radiation temperatures and energy use during passive and active (heating and cooling) measurements. Both measurement and comparative simulation results indicate an improvement in the indoor thermal environment when the interior surfaces have low emittance. In the ice rink arenas, surface and radiation temperature measurements indicate a considerable reduction in the ceiling-to-ice radiation by the use of low emittance surfaces, in agreement with a ceiling-toice radiation model using schematic dynamic heat flux calculations. The measurements in the test cabins indicate that the use of low emittance surfaces can increase the vertical indoor air temperature gradients depending on the time of day and outdoor conditions. This is in agreement with the transient CFD simulations having the boundary condition assigned on the exterior surfaces. The sensitivity analyses have been performed under different outdoor conditions and surface thermal radiation properties. The spatially resolved simulations indicate an increase in the air and surface temperature gradients by the use of low emittance coatings. This can allow for lower air temperature at the occupied zone during the summer. The combined effect of interior and exterior reflective coatings in terms of energy use has been investigated by the use of building energy simulation for different climates and internal heat loads. The results indicate possible energy savings by the smart choice of optical properties on interior and exterior surfaces of the building. Overall, it is concluded that the interior reflective coatings can contribute to building energy savings and improvement of the indoor thermal environment. This can be numerically investigated by the choice of appropriate models with respect to the level of detail and computational load. This thesis includes comparative simulations at different levels of detail.

Reindeer habitat selection under the risk of brown bear predation during calving season

The depredation of semi-domesticated reindeer by large carnivores reflects an important human-wildlife conflict in Fennoscandia. Recent studies have revealed that brown bears (Ursus arctos) may kill substantial numbers of reindeer calves (Rangifer tarandus tarandus) in forest areas in Sweden. Several authors have suggested that predation risk is an important driver of habitat selection in wild Rangifer populations where predation is a limiting factor, but little is known about these mechanisms in semi-domesticated populations. We examined the habitat selection of female reindeer in relation to spatial and temporal variations in brown bear predation risk on the reindeer calving grounds and evaluated the simultaneous responses of brown bears and reindeer to landscape characteristics. We used GPS data from 110 reindeer years (97 individuals) and 29 brown bear years (19 individuals), from two reindeer herding districts in the forest area of northern Sweden. Our results did not indicate that reindeer alter their behavior in response to spatiotemporal variation in brown bear predation risk, on the scale of the calving range. Instead, we suggest that spatiotemporal behavioral adjustments by brown bears were the main driver of prey-predator interactions in our study system. Contrasting responses by brown bears and reindeer to clear-cuts and young forest indicate that forestry can influence species interactions and possibly yield negative consequences for the reindeer herd. Even if clear-cuts may be beneficial in terms of calf survival, logging activity will eventually cause greater abundance of young regenerating forest, reducing available reindeer habitats and increasing habitat preferred by brown bears. Domestication may have made semi-domesticated reindeer in Fennoscandia less adapted to cope with predators. Areal restrictions, limiting the opportunity for dispersion and escape, possibly make the calves more susceptible to predation. Also, a generally higher population density in semi-domesticated herds compared to wild populations can make dispersion a less efficient strategy and the reindeer calves easier prey. Overall, the lack of ability of the reindeer females to reduce brown bear encounter risk on the scale of the calving range is probably an important reason for the high brown bear predation rates on reindeer calves documented in our study areas.