Wind farm construction impacts reindeer migration and movement corridors

Over the last decade, we have seen a massive increase in the construction of wind farms in northern Fennoscandia. Wind farms comprising hundreds of wind turbines are being built, with little knowledge of the possible cumulative adverse effects on the habitat use and migration of semi-domesticated free-ranging reindeer. We assessed how reindeer responded to wind farm construction in an already fragmented landscape, with specific reference to the effects on use of movement corridors and reindeer habitat selection. We used GPS-data from reindeer during calving and post-calving in the MalAyen reindeer herding community in Sweden. We analysed data from the pre-development years compared to the construction years of two relatively small wind farms. During construction of the wind farms, use of original migration routes and movement corridors within 2 km of development declined by 76 %. This decline in use corresponded to an increase in activity of the reindeer measured by increased step lengths within 0-5 km. The step length was highest nearest the development and declining with distance, as animals moved towards migration corridors and turned around or were observed in holding patterns while not crossing. During construction, reindeer avoided the wind farms at both regional and landscape scale of selection. The combined construction activities associated with even a few wind turbines combined with power lines and roads in or close to central movement corridors caused a reduction in the use of such corridors and grazing habitat and increased the fragmentation of the reindeer calving ranges.

Movements and mechanical stresses in gas-filled flat plate solar collectors

Sealed gas filled flat plate solar collectors will have stresses in the material since volume and pressure varies in the gas when the temperature changes. Several geometries were analyzed and it could be seen that it is possible reducing the stresses and improve the safety factor of the weakest point in the construction by using larger area and/or reducing the distance between glass and absorber and/or change width and height relationship so the tubes are getting longer. Further it could be shown that the safety factor won't always get improved with reinforcements. It is so because when an already strong part of the collector gets reinforced it will expose weaker parts for higher stresses. The finite element method was used for finding out the stresses.

Gas-filled, flat plate solar collectors

This work treats the thermal and mechanical performances of gas-filled, flat plate solar collectors in order to achieve a better performance than that of air filled collectors. The gases examined are argon, krypton and xenon which all have lower thermal conductivity than air. The absorber is formed as a tray connected to the glass. The pressure of the gas inside is near to the ambient and since the gas volume will vary as the temperature changes, there are potential risks for fatigue in the material. One heat transfer model and one mechanical model were built. The mechanical model gave stresses and information on the movements. The factors of safety were calculated from the stresses, and the movements were used as input for the heat transfer model where the thermal performance was calculated. It is shown that gas-filled, flat plate solar collectors can be designed to achieve good thermal performance at a competitive cost. The best yield is achieved with a xenon gas filling together with a normal thick absorber, where normal thick means a 0.25 mm copper absorber. However, a great deal of energy is needed to produce the xenon gas, and if this aspect is taken into account, the krypton filling is better. Good thermal performance can also be achieved using less material; a collector with a 0.1 mm thick copper absorber and the third best gas, which is argon, still gives a better operating performance than a common, commercially produced, air filled collector with a 0.25 mm absorber. When manufacturing gas-filled flat plate solar collectors, one way of decreasing the total material costs significantly, is by changing absorber material from copper to aluminium. Best yield per monetary outlay is given by a thin (0.3 mm) alu-minium absorber with an argon filling. A high factor of safety is achieved with thin absorbers, large absorber areas, rectangular constructions with long tubes and short distances between glass and absorber. The latter will also give a thin layer of gas which gives good thermal performance. The only doubtii ful construction is an argon filled collector with a normal thick (> 0.50 mm) aluminium absorber. In general, an assessment of the stresses for the proposed construction together with appropriate tests are recommended before manufacturing, since it is hard to predict the factor of safety; if one part is reinforced, some other parts can experience more stress and the factor of safety actually drops.

Characterization of residential chimney conditions for flue gas flow measurements

A literature survey and a theoretical study were performed to characterize residential chimney conditions for flue gas flow measurements. The focus is on Pitot-static probes to give sufficient basis for the development and calibration of a velocity pressure averaging probe suitable for the continuous dynamic (i.e. non steady state) measurement of the low flow velocities present in residential chimneys. The flow conditions do not meet the requirements set in ISO 10780 and ISO 3966 for Pitot-static probe measurements, and the methods and their uncertainties are not valid. The flow velocities in residential chimneys from a heating boiler under normal operating condi-tions are shown to be so low that they in some conditions result in voiding the assumptions of non-viscous fluid justifying the use of the quadratic Bernoulli equation. A non-linear Reynolds number dependent calibration coefficient that is correcting for the viscous effects is needed to avoid significant measurement errors. The wide range of flow velocity during normal boiler operation also results in the flow type changing from laminar, across the laminar to turbulent transition region, to fully turbulent flow, resulting in significant changes of the velocity profile during dynamic measurements. In addition, the short duct lengths (and changes of flow direction and duct shape) used in practice are shown to result in that the measurements are done in the hydrodynamic entrance region where the flow velocity profiles most likely are neither symmetrical nor fully developed. A measurement method insensitive to velocity profile changes is thus needed, if the flow velocity profile cannot otherwise be determined or predicted with reasonable accuracy for the whole measurement range. Because of particulate matter and condensing fluids in the flue gas it is beneficial if the probe can be constructed so that it can easily be taken out for cleaning, and equipped with a locking mechanism to always ensure the same alignment in the duct without affecting the calibration. The literature implies that there may be a significant time lag in the measurements of low flow rates due to viscous effects in the internal impact pressure passages of Pitot probes, and the significance in the discussed application should be studied experimentally. The measured differential pressures from Pitot-static probes in residential chimney flows are so low that the calibration and given uncertainties of commercially available pressure transducers are not adequate. The pressure transducers should be calibrated specifically for the application, preferably in combination with the probe, and the significance of all different error sources should be investigated carefully. Care should be taken also with the temperature measurement, e.g. with averaging of several sensors, as significant temperature gradients may be present in flue gas ducts.

Organisationer, ojämlikhet, migration : förändringar av den etniska arbetsdelningen i svensk byggnadssektor

Organizations, Inequality, Migration – Changes of the Ethnic Division of Labour in the Swedish Construction Sector During the 1990s the number of migrants from Eastern Europe increased in the Swedish construction sector. This article examines how this change was initiated by changes in the organizational population in the construction sector. The gradual enlargement of the European Union changed the institutional framework for organizations in Sweden. This created increased opportunities for new organizational forms in the construction sector. The specific niche of the new organizations was to recruit and hire out workers from Eastern Europe that were paid lower wages than Swedish workers. The diffusion of this organizational form contributed to a change of norms and beliefs about what was legitimate and illegitimate when employing migrants. This implies that the inequalities that this organizational form introduces have gained increased legitimacy in Sweden. Or in other words, it has become increasingly socially acceptable to pay migrants lower wages than Swedish workers

De oauktoriserade migranterna i svensk byggnadssektor : En studie i deportationspolitik 1990–2004

The unauthorized migrants in the Swedish construction sector – a study in the policy of deportation 1990–2004 The unauthorized migration of construction workers to Sweden increased during the 1990s, especially at the end of the decade. The migrants often came from Poland and the Baltic states. The aim of this article is to examine this change of the migration pattern to Sweden and how the Swedish Building Workers Union responded to this new situation. I examine how the Building Workers Union cooperated with the Police authorities to find, capture and deport unauthorized migrants. A conclusion is that the Building Workers Union has not adopted a more inclusionary strategy towards unauthorized migrants, as have trade unions in Spain and US. The main strategy has instead been to try to restrict this migration. One explanation of this is that the Building Workers Union is a strong and well organized trade union. It didn’t perceive of unauthorized migrants as potential new members, but as a threat to wages and work conditions. Another explanation is that it has been able to restrict migration in the past. This may contribute to making demands for restrictions an attractive strategy in the present even when the possibilities of succeeding with this have diminished.

Understanding the "black box" of a health-promotion program : keys to enable health among older persons aging in the context of migration

Although the need to make health services more accessible to persons who have migrated has been identified, knowledge about health-promotion programs (HPPs) from the perspective of older persons born abroad is lacking. This study explores the design experiences and content implemented in an adapted version of a group-based HPP developed in a researcher-community partnership. Fourteen persons aged 70-83 years or older who had migrated to Sweden from Finland or the Balkan Peninsula were included. A grounded theory approach guided the data collection and analysis. The findings showed how participants and personnel jointly helped raise awareness. The participants experienced three key processes that could open doors to awareness: enabling community, providing opportunities to understand and be understood, and confirming human values and abilities. Depending on how the HPP content and design are being shaped by the group, the key processes could both inhibit or encourage opening doors to awareness. Therefore, this study provides key insights into how to enable health by deepening the understanding of how the exchange of health-promoting messages is experienced to be facilitated or hindered. This study adds to the scientific knowledge base of how the design and content of HPP may support and recognize the capabilities of persons aging in the context of migration.