Energy Efficiency through Thermal Energy Storage : Possibilities for the Swedish Building Stock

The need for heating and cooling in buildings constitutes a considerable part of the total energy use in a country and reducing this need is of outmost importance in order to reach national and international goals for reducing energy use and emissions. One important way of reaching these goals is to increase the proportion of renewable energy used for heating and cooling of buildings. Perhaps the largest obstacle with this is the often occurring mismatch between the availability of renewable energy and the need for heating or cooling, hindering this energy to be used directly. This is one of the problems that can be solved by using thermal energy storage (TES) in order to save the heat or cold from when it is available to when it is needed. This thesis is focusing on the combination of TES techniques and buildings to achieve increased energy efficiency for heating and cooling. Various techniques used for TES as well as the combination of TES in buildings have been investigated and summarized through an extensive literature review. A survey of the Swedish building stock was also performed in order to define building types common in Sweden. Within the scope of this thesis, the survey resulted in the selection of three building types, two single family houses and one office building, out of which the two residential buildings were used in a simulation case study of passive TES with increased thermal mass (both sensible and latent). The second case study presented in the thesis is an evaluation of an existing seasonal borehole storage of solar heat for a residential community. In this case, real measurement data was used in the evaluation and in comparisons with earlier evaluations. The literature reviews showed that using TES opens up potential for reduced energy demand and reduced peak heating and cooling loads as well as possibilities for an increased share of renewable energy to cover the energy demand. By using passive storage through increased thermal mass of a building it is also possible to reduce variations in the indoor temperature and especially reduce excess temperatures during warm periods, which could result in avoiding active cooling in a building that would otherwise need it. The analysis of the combination of TES and building types confirmed that TES has a significant potential for increased energy efficiency in buildings but also highlighted the fact that there is still much research required before some of the technologies can become commercially available. In the simulation case study it was concluded that only a small reduction in heating demand is possible with increased thermal mass, but that the time with indoor temperatures above 24 °C can be reduced by up to 20%. The case study of the borehole storage system showed that although the storage system worked as planned, heat losses in the rest of the system as well as some problems with the system operation resulted in a lower solar fraction than projected. The work presented within this thesis has shown that TES is already used successfully for many building applications (e.g. domestic hot water stores and water tanks for storing solar heat) but that there still is much potential in further use of TES. There are, however, barriers such as a need for more research for some storage technologies as well as storage materials, especially phase change material storage and thermochemical storage.

Experimentell studie på kostnadseffektiva inkjetbestrykningspigment

The objective of this study was to evaluate and compare the print performance of some of the new most promising, cost effective absorbent pigments specialised for inkjet coatings on the market in a continuous drive to find an alternative to silica. The target was a lower production cost for ArjoWiggins inkjet products, OMD 01 and OMD 02. Five absorbent pigments are being evaluated through measuring the qualities of the coating mix itself, visual evaluations of print performance and physical testing of the coated paper. Pigments 1,2 and 3, which all are said to be tailored for inkjet coatings, did not reach the print performance needed for an OMD 01 and OMD 02 equal, due to severe bleed and feathering identified especially on the Epson 950 printer. They are therefore currently not seen as viable formulations. A blend of 50% pigment 5 and 50% silica had excellent print performance as OMD 01 and OMD 02 equivalents and is therefore recommended as a potential alternative to 100% silica. It is of the company’s interest to find a more cost effective solution to their inkjet coatings, and a 50/50 blend of Pigment 5 will save the company more than 35 000 euro per year.

Combined solar and pellet heating systems for single-family houses : How to achieve decreased electricity usage, increased system efficiency and increased solar gains

In Sweden, there are about 0.5 million single-family houses that are heated by electricity alone, and rising electricity costs force the conversion to other heating sources such as heat pumps and wood pellet heating systems. Pellet heating systems for single-family houses are currently a strongly growing market. Future lack of wood fuels is possible even in Sweden, and combining wood pellet heating with solar heating will help to save the bio-fuel resources. The objectives of this thesis are to investigate how the electrically heated single-family houses can be converted to pellet and solar heating systems, and how the annual efficiency and solar gains can be increased in such systems. The possible reduction of CO-emissions by combining pellet heating with solar heating has also been investigated. Systems with pellet stoves (both with and without a water jacket), pellet boilers and solar heating have been simulated. Different system concepts have been compared in order to investigate the most promising solutions. Modifications in system design and control strategies have been carried out in order to increase the system efficiency and the solar gains. Possibilities for increasing the solar gains have been limited to investigation of DHW-units for hot water production and the use of hot water for heating of dishwashers and washing machines via a heat exchanger instead of electricity (heat-fed appliances). Computer models of pellet stoves, boilers, DHW-units and heat-fed appliances have been developed and the parameters for the models have been identified from measurements on real components. The conformity between the models and the measurements has been checked. The systems with wood pellet stoves have been simulated in three different multi-zone buildings, simulated in detail with heat distribution through door openings between the zones. For the other simulations, either a single-zone house model or a load file has been used. Simulations were carried out for Stockholm, Sweden, but for the simulations with heat-fed machines also for Miami, USA. The foremost result of this thesis is the increased understanding of the dynamic operation of combined pellet and solar heating systems for single-family houses. The results show that electricity savings and annual system efficiency is strongly affected by the system design and the control strategy. Large reductions in pellet consumption are possible by combining pellet boilers with solar heating (a reduction larger than the solar gains if the system is properly designed). In addition, large reductions in carbon monoxide emissions are possible. To achieve these reductions it is required that the hot water production and the connection of the radiator circuit is moved to a well insulated, solar heated buffer store so that the boiler can be turned off during the periods when the solar collectors cover the heating demand. The amount of electricity replaced using systems with pellet stoves is very dependant on the house plan, the system design, if internal doors are open or closed and the comfort requirements. Proper system design and control strategies are crucial to obtain high electricity savings and high comfort with pellet stove systems. The investigated technologies for increasing the solar gains (DHW-units and heat-fed appliances) significantly increase the solar gains, but for the heat-fed appliances the market introduction is difficult due to the limited financial savings and the need for a new heat distribution system. The applications closest to market introduction could be for communal laundries and for use in sunny climates where the dominating part of the heat can be covered by solar heating. The DHW-unit is economical but competes with the internal finned-tube heat exchanger which is the totally dominating technology for hot water preparation in solar combisystems for single-family houses.

L’infidélité dans le couple : Charles et Emma Bovary dans Madame Bovary de Flaubert et Dinah et Loulou dans Traversée de la Mangrove de Maryse Condé

Ce travail sur l’infidélité dans le couple traite les différentes sources de l’ennui ainsi que leurs conséquences dans la vie du couple. Les différentes opinions de différents auteurs sur la cause de l’infidélité dans le couple sont vues en long et en large. L’éducation féminine du XIXème siècle éclaire sur le handicap qui a entrainé certaines filles dans le malheur car l’éducation de l’époque ne les avait pas bien préparées pour devenir de bonnes épouses. Ce mémoire montre l’image de la religion dans ces deux oeuvres : Madame Bovary et Traversée de la mangrove. La question est de voir comment ces auteurs peignent la religion dans ces oeuvres et pourquoi ils adoptent l’infidélité pour sauver la femme de son ennui. Enfin, la comparaison de ces ennuis est faite afin de voir que dans ces couples, malgré le fait qu’ils appartiennent à des époques différentes, l’ennui dans le couple est le même. Ces auteurs ont procédé aux mêmes stratégies pour sauver le couple de son ennui. La morale critique et religieuse a été utilisée pour aborder ce thème, lorsque nous avons fait une lecture biblique de ces deux oeuvres.

Barnmorskans uppfattning om indikationer och effekter av förlossning med elektiva kejsarsnitt på humanitär indikation utifrån arbetslivserfarenhet : En intervjustudie

Bakgrund: Statistik visar på ökat antal elektiva kejsarsnitt internationellt och nationellt. Ett kejsarsnitt kan rädda liv på mor och barn om komplikationer uppstår, elektivt kejsarsnitt är även liksom andra stora operationer förenat med risker för komplikationer. Antalet elektiva kejsarsnitt på humanitär indikation har ökat i Sverige och cirka 17 % av alla förlossningar sker via kejsarsnitt. Att vårda och stödja kvinnor före, under och efter en förlossning med kejsarsnitt hör till barnmorskans arbete. Syftet med studien var att beskriva barnmorskors uppfattning om indikationer och effekter av förlossning med elektiva kejsarsnitt på humanitär indikation belyst utifrån arbetslivserfarenheter. Metod: kvalitativ metod: semistrukturella intervjuer med nio barnmorskor. Materialet analyserades via fenomenografisk analys i sju steg. Resultat: Fyra beskrivningskategorier framkom, Elektivt kejsarsnitt på humanitär indikation är ett etiskt dilemma, Elektivt kejsarsnitt på humanitär indikation är en stor operation, Elektivt kejsarsnitt på humanitär indikation påverkar organisation och barnmorskans arbetsmiljö och Elektivt kejsarsnitt på humanitär indikation påverkar kvinnans förlossningsupplevelse. Vidare framkom nio kategorier som beskriver barnmorskors uppfattningar. Slutsats Barnmorskor uppfattar elektiva kejsarsnitt som något komplext, att de med sina yrkeskunskaper värnar det naturliga vid kejsarsnitt på humanitär indikation och att de har brist på mandat att stödja och stärka kvinnors informerade val om elektivt kejsarsnitt på humanitär indikation. Klinisk tillämpbarhet: Resultatet kan användas vid undervisning kring barnmorskans stödjande och vårdande arbete i samband med förlossning via kejsarsnitt. Vidare kan resultatet vara underlag till diskussioner inom mödrahälsovård och förlossning i syfte att ge barnmorskor stärkt mandat till sina stödjande och informativa uppgifter.