Open Issues in Control ofAutomotive R744 Air-ConditioningSystems

In this thesis, one of the current control algorithms for the R744 cycle, which tries tooptimize the performance of the system by two SISO control loops, is compared to acost-effective system with just one actuator. The operation of a key component of thissystem, a two stage orifice expansion valve is examined in a range of typical climateconditions. One alternative control loop for this system, which has been proposed byBehr group, is also scrutinized.The simulation results affirm the preference of using two control-loops instead of oneloop, but refute advantages of the Behr alternate control approach against one-loopcontrol. As far as the economic considerations of the A/C unit are concerned, usinga two-stage orifice expansion valve is desired by the automotive industry, thus basedon the experiment results, an improved logic for control of this system is proposed.In the second part, it is investigated whether the one-actuator control approach isapplicable to a system consisting of two parallel evaporators to allow passengers tocontrol different climate zones. The simulation results show that in the case of usinga two-stage orifice valve for the front evaporator and a fixed expansion valve forthe rear one, a proper distribution of the cooling power between the front and rearcompartment is possible for a broad range of climate conditions.

3D roll-forming of hat-profile with variable depth and width

The use of roll-formed products in automotive, furniture, buildings etc. increases every year due to the low part-production cost and the complicated cross-sections that can be produced. The limitation with roll-forming until recent years is that one could only produce profiles with a constant cross-section in the longitudinal direction. About eight years ago ORTIC AB [1] developed a machine in which it was possible to produce profiles with a variable width (“3D roll-forming”) for the building industry. Experimental equipment was recently built for research and prototyping of profiles with variable cross-section in both width and depth for the automotive industry. The objective with the current study is to investigate the new tooling concept that makes it possible to roll-form hat-profiles, made of ultra high strength steel, with variable cross-section in depth and width. The result shows that it is possible to produce 3D roll-formed profiles with close tolerances.

Universal Experimental Measurement System «Sun-Walker» : Automotive measurement system for the evaluation of the solar irradiation distribution for the tests of the solar concentrated systems.

This Thesis project is a part of the research conducted in Solar industry. ABSOLICON Solar Concentrator AB has invented and started production of the prospective solar concentrated system Absolicon X10. The aims of this Thesis project are designing, assembling, calibrating and putting in operation the automatic measurement system intended to evaluate distribution of density of solar radiation in the focal line of the concentrated parabolic reflectors and to measure radiation from the artificial source of light being a calibration-testing tool.On the basis of the requirements of the company’s administration and needs of designing the concentrated reflectors the operation conditions for the Sun-Walker were formulated. As the first step, the complex design of the whole system was made and division on the parts was specified. After the preliminary conducted simulation of the functions and operation conditions of the all parts were formulated.As the next steps, the detailed design of all the parts was made. Most components were ordered from respective companies. Some of the mechanical components were made in the workshop of the company. All parts of the Sun-Walker were assembled and tested. The software part, which controls the Sun-Walker work and conducts measurements of solar irradiation, was created on the LabVIEW basis. To tune and test the software part, the special simulator was designed and assembled.When all parts were assembled in the complete system, the Sun-Walker was tested, calibrated and tuned.

Russian Arctic Ports : Problems with the development and management of tourist flows

The potential changes to the territory of the Russian Arctic open up unique possibilities for the development of tourism. More favourable transport opportunities along the Northern Sea Route (NSR) create opportunities for tourism development based on the utilisation of the extensive areas of sea shores and river basins. A major challenge for the Russian Arctic sea and river ports is their strong cargo transport orientation originated by natural resource extraction industries. A careful assessment of the prospects of current and future tourism development is presented here based on the development of regions located along the shores of the Arctic ocean (including Murmansk and Arkhangelsk oblast, Nenets Autonomous okrug (AO), Yamal-Nenets AO, Taymyr AO, Republic of Sakha, Chykotsky AO). An evaluation of the present development of tourism in maritime cities suggests that a considerable qualitative and quantitative increase of tourism activities organised by domestic tourism firms is made virtually impossible. There are several factors contributing to this. The previously established Soviet system of state support for the investments into the port facilities as well as the sea fleet were not effectively replaced by creation of new structures. The necessary investments for reconstruction could be contributed by the federal government but the priorities are not set towards the increased passenger transportation. Having in mind, increased environmental pressures in this highly sensitive area it is especially vital to establish a well-functioning monitoring and rescue system in the situation of ever increasing risks which come not only from the increased transports along the NSR, but also from the exploitation of the offshore oil and gas reserves in the Arctic seas. The capacity and knowledge established in Nordic countries (Norway, Finland) concerning cruise tourism should not be underestimated and the already functioning cooperation in Barents Region should expand towards this particular segment of the tourism industry. The current stage of economic development in Russia makes it clear that tourism development is not able to compete with the well-needed increase in the cargo transportation, which means that Russia’s fleet is going to be utilised by other industries. However, opening up this area to both local and international visitors could contribute to the economic prosperity of these remote areas and if carefully managed could sustain already existing maritime cities along the shores of the Arctic Ocean.