Characterization of Chimney Flue Gas Flows : Flow Rate Measurements with Averaging Pitot Probes

Performance testing methods of boilers in transient operating conditions (start, stop and combustion power modulation sequences) need the combustion rate quantified to allow for the emissions to be quantified. One way of quantifying the combustion rate of a boiler during transient operating conditions is by measuring the flue gas flow rate. The flow conditions in chimneys of single family house boilers pose a challenge however, mainly because of the low flow velocity. The main objectives of the work were to characterize the flow conditions in residential chimneys, to evaluate the use of the Pitot-static method and the averaging Pitot method, and to develop and test a calibration method for averaging Pitot probes for low

Russian Arctic Ports : Problems with the development and management of tourist flows

The potential changes to the territory of the Russian Arctic open up unique possibilities for the development of tourism. More favourable transport opportunities along the Northern Sea Route (NSR) create opportunities for tourism development based on the utilisation of the extensive areas of sea shores and river basins. A major challenge for the Russian Arctic sea and river ports is their strong cargo transport orientation originated by natural resource extraction industries. A careful assessment of the prospects of current and future tourism development is presented here based on the development of regions located along the shores of the Arctic ocean (including Murmansk and Arkhangelsk oblast, Nenets Autonomous okrug (AO), Yamal-Nenets AO, Taymyr AO, Republic of Sakha, Chykotsky AO). An evaluation of the present development of tourism in maritime cities suggests that a considerable qualitative and quantitative increase of tourism activities organised by domestic tourism firms is made virtually impossible. There are several factors contributing to this. The previously established Soviet system of state support for the investments into the port facilities as well as the sea fleet were not effectively replaced by creation of new structures. The necessary investments for reconstruction could be contributed by the federal government but the priorities are not set towards the increased passenger transportation. Having in mind, increased environmental pressures in this highly sensitive area it is especially vital to establish a well-functioning monitoring and rescue system in the situation of ever increasing risks which come not only from the increased transports along the NSR, but also from the exploitation of the offshore oil and gas reserves in the Arctic seas. The capacity and knowledge established in Nordic countries (Norway, Finland) concerning cruise tourism should not be underestimated and the already functioning cooperation in Barents Region should expand towards this particular segment of the tourism industry. The current stage of economic development in Russia makes it clear that tourism development is not able to compete with the well-needed increase in the cargo transportation, which means that Russia’s fleet is going to be utilised by other industries. However, opening up this area to both local and international visitors could contribute to the economic prosperity of these remote areas and if carefully managed could sustain already existing maritime cities along the shores of the Arctic Ocean.

Characterization of residential chimney conditions for flue gas flow measurements

A literature survey and a theoretical study were performed to characterize residential chimney conditions for flue gas flow measurements. The focus is on Pitot-static probes to give sufficient basis for the development and calibration of a velocity pressure averaging probe suitable for the continuous dynamic (i.e. non steady state) measurement of the low flow velocities present in residential chimneys. The flow conditions do not meet the requirements set in ISO 10780 and ISO 3966 for Pitot-static probe measurements, and the methods and their uncertainties are not valid. The flow velocities in residential chimneys from a heating boiler under normal operating condi-tions are shown to be so low that they in some conditions result in voiding the assumptions of non-viscous fluid justifying the use of the quadratic Bernoulli equation. A non-linear Reynolds number dependent calibration coefficient that is correcting for the viscous effects is needed to avoid significant measurement errors. The wide range of flow velocity during normal boiler operation also results in the flow type changing from laminar, across the laminar to turbulent transition region, to fully turbulent flow, resulting in significant changes of the velocity profile during dynamic measurements. In addition, the short duct lengths (and changes of flow direction and duct shape) used in practice are shown to result in that the measurements are done in the hydrodynamic entrance region where the flow velocity profiles most likely are neither symmetrical nor fully developed. A measurement method insensitive to velocity profile changes is thus needed, if the flow velocity profile cannot otherwise be determined or predicted with reasonable accuracy for the whole measurement range. Because of particulate matter and condensing fluids in the flue gas it is beneficial if the probe can be constructed so that it can easily be taken out for cleaning, and equipped with a locking mechanism to always ensure the same alignment in the duct without affecting the calibration. The literature implies that there may be a significant time lag in the measurements of low flow rates due to viscous effects in the internal impact pressure passages of Pitot probes, and the significance in the discussed application should be studied experimentally. The measured differential pressures from Pitot-static probes in residential chimney flows are so low that the calibration and given uncertainties of commercially available pressure transducers are not adequate. The pressure transducers should be calibrated specifically for the application, preferably in combination with the probe, and the significance of all different error sources should be investigated carefully. Care should be taken also with the temperature measurement, e.g. with averaging of several sensors, as significant temperature gradients may be present in flue gas ducts.