Utredning om huruvida Dalarnas Tidningars produktion passar en KBA Cortina

This degree project illustrates newsprint and waterless offset. A new news press was introduced at Drupa-00, Cortina from KBA, which is the first news press dedicated the waterless technique. With actual statistics from the company in question an investigation was made whether their production fits this press. It came out in the investigation that the production of the company, from statistics, fits this press very good. A table was made where different timeschedules were accounted for the new press, with semi- and full automatic plate changing for present and to be added papers. The waterless technology is compared to conventional offset with the difference that the plate is based on a sort of laminatetechnology. Like conventional plates this plate has a base made of aluminium. Lightsensitive photopolymer isunited as a layer or coat on top of the aluminium and a 2µm thin oleophobic siliconlayer is applied on top of the photopolymer. Considering the print, the waterless method has a higher qualitygrade than conventional offset. No water is emulsifiedin the ink, and therefore the printed dot gets a higher density. The loss of dampening solution and higher tack of the ink gives sharper dots. This makes the colourspace bigger why a greater range of colours can be printed. The loss of dampening solution gives a more stable dotgain, which contributes to that a higher screen can be used. The disadvantage is that the plate can't do as many rotations as the conventional plate. A waterless plate makes around 100 000-500 000 rotations before it needs to be removed owing to type- and manufacturer of the plate. The plate is also slightly more sensitive and expensive than conventional plates, around 1,4 - 1,7 × aluminium printing plates. A waterless system can be installed in a conventional printing press by degrees and when large editions are being printed a cooler needs to be installed in the oscillationrollers of the press, since an increase in temperature can make the oleophobic parts of the plate oleophilic. The Cortina is however equipped with a temperature controlsystem at the beginning. To avoid picking, caused by the tacky ink, a blanket with a high “quick release” should be used.

Historiografisk metafiktion och faktion : Romantikens berättelse om den förstenade gruvdrängen Fet-Mats i två postmoderna versioner

Fet-Mats är den gruvdräng som omkom och försvann i en rasolycka i Falu koppargruva under 1670-talet och vars kropp upptäcktes välbevarad, med fortfarande ungdomligt utseende, mer än fyra årtionden senare 1719. Han igenkändes då av sin trolovade - nu en gammal gumma. På grund av den märkligt bibehållna kroppen och det hisnande ögonblick då den åldrade kvinnan återsåg sin ungdoms kärlek, blev Fet-Mats och hans historia snabbt känd, även internationellt. Den spreds under 1800- och 1900-talen i Europa som novell och poesi, dramatik och opera. Även idag berättas historien om Fet-Mats både utomlands och i Sverige. Intresset för historien är rentav i växande. Orsaken härtill är omdaningen under senare år av Falu gruva från storindustri till musealt världsarv, från malmbrytning till turistorienterad upplevelseindustri. Fet-Mats-berättelsen bildar centrum i denna upplevelseindustri. I mitt paper diskuteras detta förhållande samt den nutida Fet-Mats-epikens karakteristika i ett semiotiskt, narratologiskt och tematiskt perspektiv. Jag finner bl.a. att Fet-Mats-berättandet idag, på ett annat sätt än tidigare, äger en flermedial karaktär och formulerar det postmoderna tillståndets centrala tematik: representationens kris. Jag fokuserar särskilt på två berättelser med anknytning till Fet-Mats-motivet: Julian Barnes historiografiska metafiktion The Story of Mats Israelson (2004) och det dramadokumentära seriealbumet Fet-Mats: en gruvdrängs hemska öde (2005).

Wear of coated and uncoated PCBN cutting tool used in turning and milling

This licentiate thesis has the main focus on evaluation of the wear of coated and uncoated polycrystalline cubic boron nitride cutting tool used in cutting operations against hardened steel. And to exam the surface finish and integrity of the work material used. Harder work material, higher cutting speed and cost reductions result in the development of harder and more wear resistance cutting tools. Although PCBN cutting tools have been used in over 30 years, little work have been done on PVD coated PCBN cutting tools. Therefore hard turning and hard milling experiments with PVD coated and uncoated cutting tools have been performed and evaluated. The coatings used in the present study are TiSiN and TiAlN. The wear scar and surface integrity have been examined with help of several different characterization techniques, for example scanning electron microscopy and Auger electron spectroscopy.   The results showed that the PCBN cutting tools used displayed crater wear, flank wear and edge micro chipping. While the influence of the coating on the crater and flank wear was very small and the coating showed a high tendency to spalling. Scratch testing of coated PCBN showed that, the TiAlN coating resulted in major adhesive fractures. This displays the importance of understanding the effect of different types of lapping/grinding processes in the pre-treatment of hard and super hard substrate materials and the amount and type of damage that they can create. For the cutting tools used in turning, patches of a adhered layer, mainly consisting of FexOy were shown at both the crater and flank. And for the cutting tools used in milling a tribofilm consisting of SixOy covered the crater. A combination of tribochemical reactions, adhesive wear and mild abrasive wear is believed to control the flank and crater wear of the PCBN cutting tools. On a microscopic scale the difference phases of the PCBN cutting tool used in turning showed different wear characteristics. The machined surface of the work material showed a smooth surface with a Ra-value in the range of 100-200 nm for the turned surface and 100-150 nm for the milled surface. With increasing crater and flank wear in combination with edge chipping the machined surface becomes rougher and showed a higher Ra-value. For the cutting tools used in milling the tendency to micro edge chipping was significant higher when milling the tools steels showing a higher hard phase content and a lower heat conductivity resulting in higher mechanical and thermal stresses at the cutting edge.