Heat losses and thermal performance of commercial combined solar and pellet heating systems

Various pellet heating systems are marketed in Sweden, some of them in combination with a solar heating system. Several types of pellet heating units are available and can be used for a combined system. This article compares four typical combined solar and pellet heating systems: System 1 and 2 two with a pellet stove, system 3 with a store integrated pellet burner and system 4 with a pellet boiler. The lower efficiency of pellet heaters compared to oil or gas heaters increases the primary energy demand. Consequently heat losses of the various systems have been studied. The systems have been modeled in TRNSYS and simulated with parameters identified from measurements. For almost all systems the flue gas losses are the main heat losses except for system 3 where store heat losses prevail. Relevant are also the heat losses of the burner and the boiler to the ambient. Significant leakage losses are noticed for system 3 and 4. For buildings with an open internal design system 1 is the most efficient solution. Other buildings should preferably apply system 3. The right choice of the system depends also on whether the heater is placed inside or outside of the heated are. A large potential for system optimization exist for all studied systems, which when applied could alter the relative merits of the different system types.

COMPARISON OF PARTIAL SHADING LOSSES IN FREE FIELD PV-PLANTS WITH DIFFERENT ARRAY CONFIGURATIONS

A common problem when planning large free field PV-plants is optimizing the ground occupation ratio while maintaining low shading losses. Due to the complexity of this task, several PV-plants have been built using various configurations. In order to compare the shading losses of different PV technologies and array designs, empirical performance data of five free field PV-plants operating in Germany was analyzed. The data collected comprised 140 winter days from October 2011 until March 2012. The relative shading losses were estimated by comparing the energy output of selected arrays in the front rows (shading-free) against that of shaded arrays in the back rows of the same plant. The results showed that landscape mounting with mc-Si PV-modules yielded significantly better results than portrait one. With CIGS modules, making cross-table strings using the lower modules was not beneficial as expected and had more losses than a one-string-per-table layout. Parallel substrings with CdTe showed relatively low losses. Among the two CdTe products analyzed, none showed a significantly better performance.

Health care providers' perceptions of and attitudes towards induced abortions in sub-Saharan Africa and Southeast Asia : a systematic literature review of qualitative and quantitative data.

BACKGROUND: Unsafe abortions are a serious public health problem and a major human rights issue. In low-income countries, where restrictive abortion laws are common, safe abortion care is not always available to women in need. Health care providers have an important role in the provision of abortion services. However, the shortage of health care providers in low-income countries is critical and exacerbated by the unwillingness of some health care providers to provide abortion services. The aim of this study was to identify, summarise and synthesise available research addressing health care providers' perceptions of and attitudes towards induced abortions in sub-Saharan Africa and Southeast Asia. METHODS: A systematic literature search of three databases was conducted in November 2014, as well as a manual search of reference lists. The selection criteria included quantitative and qualitative research studies written in English, regardless of the year of publication, exploring health care providers' perceptions of and attitudes towards induced abortions in sub-Saharan Africa and Southeast Asia. The quality of all articles that met the inclusion criteria was assessed. The studies were critically appraised, and thematic analysis was used to synthesise the data. RESULTS: Thirty-six studies, published during 1977 and 2014, including data from 15 different countries, met the inclusion criteria. Nine key themes were identified as influencing the health care providers' attitudes towards induced abortions: 1) human rights, 2) gender, 3) religion, 4) access, 5) unpreparedness, 6) quality of life, 7) ambivalence 8) quality of care and 9) stigma and victimisation. CONCLUSIONS: Health care providers in sub-Saharan Africa and Southeast Asia have moral-, social- and gender-based reservations about induced abortion. These reservations influence attitudes towards induced abortions and subsequently affect the relationship between the health care provider and the pregnant woman who wishes to have an abortion. A values clarification exercise among abortion care providers is needed.

Novel Statistical Methods in Quantitative Genetics : Modeling Genetic Variance for Quantitative Trait Loci Mapping and Genomic Evaluation

This thesis develops and evaluates statistical methods for different types of genetic analyses, including quantitative trait loci (QTL) analysis, genome-wide association study (GWAS), and genomic evaluation. The main contribution of the thesis is to provide novel insights in modeling genetic variance, especially via random effects models. In variance component QTL analysis, a full likelihood model accounting for uncertainty in the identity-by-descent (IBD) matrix was developed. It was found to be able to correctly adjust the bias in genetic variance component estimation and gain power in QTL mapping in terms of precision.  Double hierarchical generalized linear models, and a non-iterative simplified version, were implemented and applied to fit data of an entire genome. These whole genome models were shown to have good performance in both QTL mapping and genomic prediction. A re-analysis of a publicly available GWAS data set identified significant loci in Arabidopsis that control phenotypic variance instead of mean, which validated the idea of variance-controlling genes.  The works in the thesis are accompanied by R packages available online, including a general statistical tool for fitting random effects models (hglm), an efficient generalized ridge regression for high-dimensional data (bigRR), a double-layer mixed model for genomic data analysis (iQTL), a stochastic IBD matrix calculator (MCIBD), a computational interface for QTL mapping (qtl.outbred), and a GWAS analysis tool for mapping variance-controlling loci (vGWAS).

MAPfastR : quantitative trait loci mapping in outbred line crosses

MAPfastR is a software package developed to analyze QTL data from inbred and outbred line-crosses. The package includes a number of modules for fast and accurate QTL analyses. It has been developed in the R language for fast and comprehensive analyses of large datasets. MAPfastR is freely available at: http://www.computationalgenetics.se/?page_id=7.

Thermal losses in sealed, gas-filled flat plate solar collectors

A sealed space between absorber and cover glass makes it possible reducing the influence of humidity condensate and dust at the same time as the enclosed space can be filled with a suitable gas for lowering the losses. This paper is about the size of the losses in these collectors. A calculating model of a gas-filled flat plate solar collector was built in Matlab with standard heat transfer formulas. It showed that the total loss can be reduced up to 20% when changing to an inert gas. It is also possible using a much shorter distance and still achieve low losses at the same time as the mechanical stresses in the material is reduce.