Identifiering av parametrar till ackumulatortanken Solus1050 från consolar - en metodbeskrivning

This report describes the work done creating a computer model of a kombi tank from Consolar. The model was created with Presim/Trnsys and Fittrn and DF were used to identify the parameters. Measurements were carried out and were used to identify the values of the parameters in the model. The identifications were first done for every circuit separately. After that, all parameters are normally identified together using all the measurements. Finally the model should be compared with other measurements, preferable realistic ones. The two last steps have not yet been carried out, because of problems finding a good model for the domestic hot water circuit.The model of the domestic hot water circuit give relatively good results for low flows at 5 l/min, but is not good for higher flows. In the report suggestions for improving the model are given. However, there was not enough time to test this within the project as much time was spent trying to solve problems with the model crashing. Suggestions for improving the model for the domestic circuit are given in chapter 4.4. The improved equations that are to be used in the improved model are given by equation 4.18, 4.19 and 4.22.Also for the boiler circuit and the solar circuit there are improvements that can be done. The model presented here has a few shortcomings, but with some extra work, an improved model can be created. In the attachment (Bilaga 1) is a description of the used model and all the identified parameters.A qualitative assessment of the store was also performed based on the measurements and the modelling carried out. The following summary of this can be given: Hot Water PreparationThe principle for controlling the flow on the primary side seems to work well in order to achieve good stratification. Temperatures in the bottom of the store after a short use of hot water, at a coldwater temperature of 12°C, was around 28-30°C. This was almost independent of the temperature in the store and the DHW-flow.The measured UA-values of the heat exchangers are not very reliable, but indicates that the heat transfer rates are much better than for the Conus 500, and in the same range as for other stores tested at SERC.The function of the mixing valve is not perfect (see diagram 4.3, where Tout1 is the outlet hot water temperature, and Tdhwo and Tdhw1 is the inlet temperature to the hot and cold side of the valve respectively). The outlet temperature varies a lot with different temperatures in the storage and is going down from 61°C to 47°C before the cold port is fully closed. This gives a problem to find a suitable temperature setting and gives also a risk that the auxiliary heating is increased instead of the set temperature of the valve, when the hot water temperature is to low.Collector circuitThe UA-value of the collector heat exchanger is much higher than the value for Conus 500, and in the same range as the heat exchangers in other stores tested at SERC.Boiler circuitThe valve in the boiler circuit is used to supply water from the boiler at two different heights, depending on the temperature of the water. At temperatures from the boiler above 58.2°C, all the water is injected to the upper inlet. At temperatures below 53.9°C all the water is injected to the lower inlet. At 56°C the water flow is equally divided between the two inlets. Detailed studies of the behaviour at the upper inlet shows that better accuracy of the model would have been achieved using three double ports in the model instead of two. The shape of the upper inlet makes turbulence, that could be modelled using two different inlets. Heat lossesThe heat losses per m3 are much smaller for the Solus 1050, than for the Conus 500 Storage. However, they are higher than those for some good stores tested at SERC. The pipes that are penetrating the insulation give air leakage and cold bridges, which could be a major part of the losses from the storage. The identified losses from the bottom of the storage are exceptionally high, but have less importance for the heat losses, due to the lower temperatures in the bottom. High losses from the bottom can be caused by air leakage through the insulation at the pipe connections of the storage.

Improved Road Design for Future Maintenance - Analysis of Road Barrier Repair Costs

The cost of a road construction over its service life is a function of the design, quality of construction, maintenance strategies and maintenance operations. Unfortunately, designers often neglect a very important aspect which is the possibility to perform future maintenance activities. The focus is mainly on other aspects such as investment costs, traffic safety, aesthetic appearance, regional development and environmental effects. This licentiate thesis is a part of a Ph.D. project entitled “Road Design for lower maintenance costs” that aims to examine how the life-cycle costs can be optimized by selection of appropriate geometrical designs for the roads and their components. The result is expected to give a basis for a new method used in the road planning and design process using life-cycle cost analysis with particular emphasis on road maintenance. The project started with a review of literature with the intention to study conditions causing increased needs for road maintenance, the efforts made by the road authorities to satisfy those needs and the improvement potential by consideration of maintenance aspects during planning and design. An investigation was carried out to identify the problems which obstruct due consideration of maintenance aspects during the road planning and design process. This investigation focused mainly on the road planning and design process at the Swedish Road Administration. However, the road planning and design process in Denmark, Finland and Norway were also roughly evaluated to gain a broader knowledge about the research subject. The investigation was carried out in two phases: data collection and data analysis. Data was collected by semi-structured interviews with expert actors involved in planning, design and maintenance and by a review of design-related documents. Data analyses were carried out using a method called “Change Analysis”. This investigation revealed a complex combination of problems which result in inadequate consideration of maintenance aspects. Several urgent needs for changes to eliminate these problems were identified. Another study was carried out to develop a model for calculation of the repair costs for damages of different road barrier types and to analyse how factors such as road type, speed limits, barrier types, barrier placement, type of road section, alignment and seasonal effects affect the barrier damages and the associated repair costs. This study was carried out using a method called the “Case Study Research Method”. Data was collected from 1087 barrier repairs in two regional offices of the Swedish Road Administration, the Central Region and the Western Region. A table was established for both regions containing the repair cost per vehicle kilometre for different combinations of barrier types, road types and speed limits. This table can be used by the designers in the calculation of the life-cycle costs for different road barrier types.

Bullerförekomst vid sönderdelning av skogsbränsle

Syftet med denna studie är att öka kunskapen om bullerexponering för omgivning och förare vid sönderdelning av skogsbränsle till flis. Sammanlagt har sex fallstudier genomförts, tre skotare, två lastbilar och en mobil anläggning. Fallen har valts med syftet att representera olika typer av sönderdelningsekipage och teknik. Studierna har genomförts i Dalarnas, Stockholms och Gävleborgs län. Bullerexponering för omgivning och förare i samband med sönderdelning till flis har undersökts med föreskrivna metoder. Det är stora skillnader på bullerexponering för förarna av de olika ekipagen. En skotarförare har daglig bullerexponering under såväl insats- som gränsvärde. Två förare (en skotarförare och en lastbilsförare) överskred insatsvärde, men var under gränsvärdet. Övriga förares bullerexponering överskred gränsvärdet. Alla maskiner har bullernivåer över 40/45 dB(A) på 200 meters avstånd, vilket överstiger acceptabla nivåer dagtid för områden med fritidsbebyggelse och fritidsområden. Endast ett av ekipagen (en skotare) hade bullernivåer på 200 meters avstånd i nivå med riktlinjer för områden med bostäder för permanent boende.  Övriga ekipage hade högre värden. De slutsatser som kan göras från denna studie är: Merparten av förare vid sönderdelning av skogsbränsle till flis exponeras för dagliga bullernivåer som kräver åtgärder. Bullernivåerna varierar mellan olika typer av ekipage för sönderdelning av skogsbränsle till flis. Studerade ekipage har högre värden för buller på 200 meters avstånd till bostäder, arbetslokaler och friluftsområden än vad som rekommenderas.

Damm- och mögelförekomst vid hantering av skogsbränsle

Tidigare studier har indikerat att exponering för trädamm och mögeldamm vid hantering av GROT (grenar och toppar) kan vara en hälsorisk. Syftet med denna studie är att ytterligare öka kunskapen om dammförhållanden inom skogsenergibranschen. Mer specifikt är målet att genom fallstudier studera dammförekomst vid hantering av GROT samt stubbar. Enstaka fallstudier av mögelförekomst i förarmiljön inkluderas. Sammanlagt har 19 fallstudier genomförts hos tio olika företag i Dalarna, Västmanland, ödermanland, Uppland, och Närke. Totaldamm har mätts med filterprovtagning inne i hytten och utanför hytten. Mögel har mätts med filterprovtagning inne i hytten. Sammanfattningsvis kan konstateras att vid samtliga fall av skotning uppmättes förhöjda dammnivåer utomhus. Högst dammnivåer uppmättes vid sönderdelning av GROT vid olika årstider. Förare som utförde arbete utanför hytten exponerades för högre dammnivåer än de som enbart arbetade inifrån hytten. De enstaka fallstudierna av mögel visade på relativt låga värden av mögelsporer. Arbetsmomentet såsom byte av knivar indikerade ökade mögelhalter. Slutsatser från denna studie är: Inga höga damm och mögelhalter har uppmätts i dessa fallstudier. Då väderförhållandena innebar mer nederbörd än i genomsnitt är resultaten inte generaliserbara. Förhöjda dammhalter uppmättes då förare utfört service och underhållsarbete utanför hytten. I studerade fall där dammängden utanför hytten var förhöjd har inga dammhalter mätts upp inne i hytterna, vilket tyder på bra luftfilter. Rekommendationer till förare är att: Regelbundet byta hyttens luftfilter och att hålla fönster och dörrar stängda för att förhindra dammexponering inne i hytten. Vid service- och underhållsarbete ska föraren i möjligaste mån undvika att använda tryckluft. Andningsskydd bör användas under de korta moment som tryckluft används.

Arbetsmiljö vid service- och reparation av skogsbränslemaskiner

Syftet med denna studie är att ta fram underlag till en arbetsmiljöchecklista för service och reparationsarbete av skogsbränslemaskiner. Däri ingår maskiner för skördning, transport och sönderdelning av sortimenten GROT (grenar och toppar), stubbar respektive klenskog. En avgränsning har gjorts till service och reparationsarbete som görs ute i fält. Tjugotre riktade fallstudier har genomförts i Mellansverige med fokus på service- och reparationsarbete som skett ute i fält. Arbetsmiljöfaktorer har observerats och dokumenterats med foto, samtal har förts med förare och servicemän, och mätningar av buller och damm har genomförts. Vid samtal med förare har efterfrågats hur ofta service och reparationsarbete genomförs, vem som gör det, vilka moment som ingår samt var det vanligtvis utförs. Servicearbete ingår i förarens arbetsuppgifter och förekommer med olika intervall. Vissa arbetsmoment utförs dagligen, såsom byte av huggstål, smörjning av krannipplar och renblåsning av container. Andra sker med längre intervall, såsom byte av oljor och filter. I studien har tillvägagångssätt och arbetsmiljörisker vid omfattande, respektive mindre, service- ochreparationsarbete identifierats. Service- och reparationsarbete är ofta tungt och smutsigt.Arbetsmiljörisker samt goda exempel på lösningar för olika typer av maskiner har sammanställts.Baserat på studiens empiriska resultat, genomförda litteraturstudier och analyser harcheckpunkter som bör ingå i en arbetsmiljöchecklista identifierats. Identifierade checkpunkternahar grupperats utifrån målgrupp och typ av arbetsmoment med syftet att vara praktisktanvändbara. Målgrupperna är maskintillverkare/ägare som modifierar maskiner, respektiveservicemän och förare. Framtagna checkpunkter utgör en grund till en checklista för arbete medservice- och reparationsarbete av skogsbränslemaskiner.

Testing common nonlinear features in vector nonlinear autoregressive models

This paper studies a special class of vector smooth-transition autoregressive (VSTAR) models that contains common nonlinear features (CNFs), for which we proposed a triangular representation and developed a procedure of testing CNFs in a VSTAR model. We first test a unit root against a stable STAR process for each individual time series and then examine whether CNFs exist in the system by Lagrange Multiplier (LM) test if unit root is rejected in the first step. The LM test has standard Chi-squared asymptotic distribution. The critical values of our unit root tests and small-sample properties of the F form of our LM test are studied by Monte Carlo simulations. We illustrate how to test and model CNFs using the monthly growth of consumption and income data of United States (1985:1 to 2011:11).

Forecasting with Vector Nonlinear Time Series Models

This work concerns forecasting with vector nonlinear time series models when errorsare correlated. Point forecasts are numerically obtained using bootstrap methods andillustrated by two examples. Evaluation concentrates on studying forecast equality andencompassing. Nonlinear impulse responses are further considered and graphically sum-marized by highest density region. Finally, two macroeconomic data sets are used toillustrate our work. The forecasts from linear or nonlinear model could contribute usefulinformation absent in the forecasts form the other model.

Residual-based Inference for Common Nonlinear Features

This paper investigates common nonlinear features in multivariate nonlinear autore-gressive models via testing the estimated residuals. A Wald-type test is proposed and itis asymptotically Chi-squared distributed. Simulation studies are given to examine thefinite-sample properties of the proposed test.

Testing linear cointegration against smooth-transition cointegration

This paper studies a smooth-transition (ST) type cointegration. The proposed ST cointegration allows for regime switching structure in a cointegrated system. It nests the linear cointegration developed by Engle and Granger (1987) and the threshold cointegration studied by Balke and Fomby (1997). We develop F-type tests to examine linear cointegration against ST cointegration in ST-type cointegrating regression models with or without time trends. The null asymptotic distributions of the tests are derived with stationary transition variables in ST cointegrating regression models. And it is shown that our tests have nonstandard limiting distributions expressed in terms of standard Brownian motion when regressors are pure random walks, while have standard asymptotic distributions when regressors contain random walks with nonzero drift. Finite-sample distributions of those tests are studied by Monto Carlo simulations. The small-sample performance of the tests states that our F-type tests have a better power when the system contains ST cointegration than when the system is linearly cointegrated. An empirical example for the purchasing power parity (PPP) data (monthly US dollar, Italy lira and dollar-lira exchange rate from 1973:01 to 1989:10) is illustrated by applying the testing procedures in this paper. It is found that there is no linear cointegration in the system, but there exits the ST-type cointegration in the PPP data.