Koldiffusionens inverkan på utmattnings-hållfastheten hos varmvalsade sexkantsstänger;The influence of carbon diffusion on the fatigue strength of hot rolled hexagonal rods

Helstångsborr och konstång kallas bergborrverktyg, som tillverkas av sexkantiga stänger med inre hål för ledning av spolvatten. Dessa spolhål är klädda med ferritiskt rostfritt stål. Innan valsning borras ett centrerat hål i stålämnet som ska valsas. I det borrade hålet appliceras ett rör av ferritiskt rostfritt stål och i det röret skjuts en manganstålskärna in. Efter valsning dras kärnan ut och ett spolhål med invändigt foder av rostfritt stål bildas. Under uppvärmningen och valsningen av stålämnet sker normalt en koldiffusion från manganstålskärnan till det rostfria fodret. Fodrets syfte är att skydda spolhålets yta mot erosion och korrosion.Syftet med arbetet var att hitta en metod som garanterar uppkolning av det invändiga fodret, samt att utreda vad uppkolningen betyder för den mekaniska hållfastheten i stängerna. Ett laboratorieförsök visade att det var bra, med avseende på uppkolning, att blanda stearat i kärnbestrykningsmedlet. Kärnbestrykningsmedlet penslas på manganstålskärnan innan den förs in i stålämnet som ska valsas, dess syfte är att minska friktionen vid kärnutdragningen efter valsning.Ett försök utfördes i valsverket med stearat i kärnbestrykningsmedlet. En grundlig undersökning utfördes på två hetor som valsats med stearat-bestrykningsmedel, samt på en traditionellt tillverkad heta för att ha som referens. Hetorna kapades till provstänger om 1,5 m, totalt undersöktes 55 st.Utvärderingen av verksförsöket visade att stängernas kvalitet blir tillräckligt bra om ingenting oförutsett händer i produktionen, oavsett om koltillskott är tillsatt i bestrykningsmedlet eller inte. Arbetet gav inte en garanterande metod, men visade att stängerna normalt håller hög kvalitet.

Faktorer som påverkar uppkomsten av hot och våld inom psykiatrin

Syftet med denna systematiska litteraturstudie var att beskriva faktorer som påverkade uppkomsten av hot och våld inom psykiatrin. Till resultatet har författarna använt sig av tjugoen vetenskapliga artiklar som hämtats ur Högskolan dalarnas databaser ELIN, Academic Search Elite samt Cinahl. Sökord i olika kombinationer har använts för att få fram relevant litteratur till studien. De sökord som användes var violence, nursing, mental health nurses, aggressive patients, aggressive behaviour, psychiatric units, patients, factors, prevention, aggression, nurses, psychiatric, management, psychiatry och causes. Även manuell sökning i tidskrifter har gjorts. Artiklarna skulle vara publicerade tidigast år 2000 om inte tidigare studier ansågs innehålla relevant fakta för studien. Granskning av artiklarna genomfördes med hjälp av granskningsmallar. Resultatet visade att bemötandet av patienter inom psykiatrisk vård var av stor betydelse för om hotfulla och våldsamma incidenter skulle inträffa. Att som vårdpersonal försöka förstå anledningen till den uppkomna situationen kunde leda till att dessa situationer kunde undvikas. Patienterna upplevde ofta att personalen inte lyssnade och detta var en vanlig orsak till att våldsamma incidenter uppstod. Vårdpersonalen ansåg istället att patientens sjukdom var orsaken till uppkomsten av hot och våld. På avdelningar där patienter med paranoida och psykotiska tendenser var intagna ökade risken för våldsamma situationer. Patienterna upplevde ofta tiden på den psykiatriska avdelningen som långtråkig och det påverkade stämningen. Både vårdpersonal och patienter ansåg att mer aktiviteter skulle minska aggressionen på avdelningen.

Haren. Ett hot mot idrottens värde?

Inom friidrottens löpgrenar kan man idag se vid de stora galorna att det finns en person som har till uppgift att springa före övriga deltagare och springa i en viss fart som har beställts antingen av arrangörerna eller någon löpare. Denna person kallas för "hare" vars huvuduppgift är att se till att ett visst tempo hålls under loppet. Men vad har detta fenomen för effekt på idrottens värde? Detta arbete ger en beskrivning av fenomenet "haren" både ur historiskt perspektiv samt hur det ser ut i nutida läge. Genom diverse teorier om vad som skapar värde inom idrott och hur idrott bör utföras för att uppfattas som mer "äkta" har fenomenet sedan analyserats för att bestämma om fenomenet är något positivt eller negativt för idrottens värde. Prestationer är något som ska genomföras på egen hand och idrottaren skall besitta de resurser som krävs för att kunna genomföra ett lopp helt på egen hand och kunna hantera både interna och externa påfrestningar. Att inte veta vem som kommer att vinna är den ovisshet som skapar spänning och därmed värde inom idrott. Med haren har man eliminerat denna ovisshet för att i stället få spänning genom att fokusera loppen på att slå rekord. Detta sätt att skapa prestationer har en mycket negativ påverkan på idrottens värde vilket får en detaljerad analys i detta arbete.

Calucaltion of waste heat from hot rolled steel coils at SSAB and its recovery

Hot rolling process is heat input process. The heat energy in hot rolled steel coils can be utilized. At SSAB Strip Product Borlänge when the hot rolled steel coils came out of the hot rolling mill they are at the temperature range of 500°C to 800°C. Heat energy contained by the one hot rolled steel coil is about 1981Kwh whereas the total heat energy for the year 2008 is 230 GWh/year.The potential of heat is too much but the heat dissipation rate is too slow. Different factors on which heat dissipation rate depends are discussed.Three suggestions are proposed to collect the waste heat from hot rolled steel coils.The 2nd proposal in which water basin is suggested would help not only to collect the waste heat but to decrease in the cooling time.

Hot och våld i socialarbetares yrkesutövning : Threats and violence in the socialwelfare secretary occupation.

2004, the SSR, Akademikerförbundet, made a study on the threats and violence as a social secretary in the municipal social services are exposed in their occupation of the "social secretary of threats and violence at work" (T-110192), conducted by Temo ab. We have chosen to use the study on a smaller scale and then made contact with five municipalities in the middle of Sweden to investigate social secretaries experiences of threats and violence. Using the cross-sectional design and a convenience sample, we have gained access to data from 56 people. From a sociological perspective, we have chosen to use Norbert Elias theory of universal configuration and interdependence, and Michel Foucault’s theories concerning power search explanation for the existence of threats and violent situations in the contact between social workers and their clients.

Behaviour of Surface Defects in Wire Rod Rolling

Defects are often present in rolled products, such as wire rod. The markets demand for wire rod without any defects has increased. In the final wire rod products, defects originating from the steel making, casting, pre-rolling of billets and during the wire rod rolling can appear. In this work, artificial V-shaped longitudinal surface cracks has been analysed experimentally and by means of FEM. The results indicate that the experiments and FEM calculations show the same tendency except in two cases, where instability due to a fairly “round” false round bars disturbed the experiment. FE studies in combination with practical experiments are necessary in order to understand the behaviour of the material flows in the groove and to explain whether the crack will open up as a V-shape or if it will be closed as an I-shape.

Modeling precipitation and its effect on recrystallization during hot strip rolling of niobium steels

Using a physically based model, the microstructural evolution of Nb microalloyed steels during rolling in SSAB Tunnplåt’s hot strip mill was modeled. The model describes the evolution of dislocation density, the creation and diffusion of vacancies, dynamic and static recovery through climb and glide, subgrain formation and growth, dynamic and static recrystallization and grain growth. Also, the model describes the dissolution and precipitation of particles. The impeding effect on grain growth and recrystallization due to solute drag and particles is accounted for. During hot strip rolling of Nb steels, Nb in solid solution retards recrystallization due to solute drag and at lower temperatures strain-induced precipitation of Nb(C,N) may occur which effectively retard recrystallization. The flow stress behavior during hot rolling was calculated where the mean flow stress values were calculated using both the model and measured mill data. The model showed that solute drag has an essential effect on recrystallization during hot rolling of Nb steels.

Tribological Testing of Some Potential PVD and CVD Coatings for Steel Wire Drawing Dies

Cemented carbide is today the most frequently used drawing die material in steel wire drawing applications. This is mainly due to the possibility to obtain a broad combination of hardness and toughness thus meeting the requirements concerning strength, crack resistance and wear resistance set by the wire drawing process. However, the increasing cost of cemented carbide in combination with the possibility to increase the wear resistance of steel through the deposition of wear resistant CVD and PVD coatings have enhanced the interest to replace cemented carbide drawing dies with CVD and PVD coated steel wire drawing dies. In the present study, the possibility to replace cemented carbide wire drawing dies with CVD and PVD coated steel drawing dies have been investigated by tribological characterisation, i.e. pin-on-disc and scratch testing, in combination with post-test observations of the tribo surfaces using scanning electron microscopy, energy dispersive X-ray spectroscopy and 3D surface profilometry. Based on the results obtained, CVD and PVD coatings aimed to provide improved tribological performance of steel wire drawing dies should display a smooth surface topography, a high wear resistance, a high fracture toughness (i.e. a high cracking and chipping resistance) and intrinsic low friction properties in contact with the wire material. Also, the steel substrate used must display a sufficient load carrying capacity and resistance to thermal softening. Of the CVD and PVD coatings evaluated in the tribological tests, a CVD TiC and a PVD CrC/C coating displayed the most promising results.

Tribology in Metal Working

This thesis focuses on the tribological performance of tool surfaces in two steel working operations, namely wire drawing and hot rolling. In all forming operations dimensions and surface finish of the products are of utmost importance. Forming basically includes three parts – forming conditions excluded – that may be changed; work material, tool and (possibly) lubricant. In the interface between work material and tool, the conditions are very aggressive with – generally or locally – high temperatures and pressures. The surfaces will be worn in various ways and this will change the conditions in the process. Consequently, the surface finish as well as the dimensions of the formed product may change and in the end, the product will not fulfil the requirements of the customer. Therefore, research and development in regard to wear, and consequently tribology, of the forming tools is of great interest. The investigations of wire drawing dies focus on coating adhesion/cohesion, surface characteristics and material transfer onto the coated steel both in laboratory scale as well as in the wire drawing process. Results show that it in wire drawing is possible to enhance the tribological performance of drawing dies by using a lubricant together with a steel substrate coated by a polished, dual-layer coating containing both hard and friction-lowering layers. The investigations of hot rolling work rolls focus on microstructure and hardness as well as cracking- and surface characteristics in both laboratory scale and in the hot strip mill. Results show that an ideal hot work roll material should be made up of a matrix with high hardness and a large amount of complex, hard carbides evenly distributed in the microstructure. The surface failure mechanisms of work rolls are very complex involving plastic deformation, abrasive wear, adhesive wear, mechanical and thermal induced cracking, material transfer and oxidation. This knowledge may be used to develop new tools with higher wear resistance giving better performance, lower costs and lower environmental impact.

An investigation of worn work roll materials used in the finishing stands of the hot strip mill for steel rolling

The surface failure characteristics of different work roll materials, i.e. High Speed Steel, High Chromium Iron and Indefinite Chill Iron, used in the finishing stands of a hot strip mill have been investigated using stereo microscopy, 3D optical profilometry, scanning electron microscopy and energy dispersive X-ray spectroscopy. The results show that the surface failure mechanisms of work rolls for hot rolling are very complex, involving plastic deformation, abrasive wear, adhesive wear, mechanical and thermal induced cracking, material transfer and oxidation. Despite the differences in chemical composition and microstructure, the tribological response of the different work roll materials was found to be strongly dependent on the material microstructure and especially the presence and distribution of microstructural constituents, such as the different carbide phases and graphite (in the case of Indefinite Chill Iron). Cracking and chipping of the work roll surfaces, both having a negative impact on work roll wear, are strongly influenced by the presence of carbides, carbide networks and graphite in the work roll surface. Consequently, the amount of carbide forming elements as well as the manufacturing process must be controlled in order to obtain an optimised microstructure and a predictable wear rate.

Pedagoger i det sociala uppdragets gränstrakter : Att hantera familjerättsliga processer, hot och våld

Pedagogues in the borderland of their social task: dealing with family law proceedings, threats and violence Drawing upon an explorative study of family law proceedings from a school perspective, the aim of this paper is to examine the school staff’s strategies for solving or coping with problematic situations in this context. Gendered conflicts between adults and violence are extreme cases for pedagogues in school and preschool. How do the staff cope with their own and the children’s vulnerability? Based upon interviews with 22 informants, the staff’s strategies are outlined and discussed in relation to organizational and professional circumstances and intersecting social relations of power. An analytical construction of six types of proactive and reactive strategies, ranging from distance keeping to normalization of own exposure, is utilized in the analysis. Findings suggest that the staff’s strategies to handle challenging events in this context vary with the parent’s gender, class position and ethnicity. Further, it is argued that creating a sense of safety and promoting learning among the children may be obstructed by lack of support from the school’s organization, demands on staff to perform customer oriented attitudes towards parents and lack of clarity concerning the limits of the social task. Conflicts between the organization and profession on the one hand and the educational and the social task on the other hand, are thus illuminated. In conclusion, a further aim of this article is to contribute to broader discussions on men’s violence against women and children – in families as well as in workplaces and in the intersection between these two areas. 

Ökat hot och våld i arbetslivet – en följd av förändrade arbetsförhållanden? : En studie utifrån de svenska Arbetsmiljöundersökningarna 1991–2005

Increase in work related violence. A reflection of changes in working conditions? An analysis based on the Swedish Work Environment surveys. Victim surveys from Sweden show that the proportion reporting exposure to work related violence has increased. On the basis of the Swedish Work Environment surveys 1991–2005 this article focuses on the following questions: What kind of situations and working conditions are related to workplace violence? And, has the number of employees exposed to these working conditions increased parallel to the rise of reported workplace violence? Logistic regression analysis shows that some situations and working conditions are indeed related tothe risk of violence. To some extent exposure to these working conditions co-varies with exposure to violence. This result is more prominent for women than for men. Further research is needed to understand how changes in working conditions affect the risk of violence and the development thereof, not least from a gender perspective. Even so, changes in working conditions can not alone explain the increase of reported workplace violence in Sweden during this period. It seems that the influence of changed working conditions offers an interesting complement to criminological theories of broadened definitions and decreasing tolerance against violence in problematizing how an increase in reported workplace violence should and could be understood.