Evaluation of galling resistance for some selected combinations of tool steels/stainless steel sheet materials/lubricants using pin-on-disc testing

Stainless steels are well known to be prone to cold welding and material transfer in sliding contacts and therefore difficult to cold form unless certain precautions as discussed in this paper are taken. In the present study different combinations of tool steels/stainless steels/lubricants has been evaluated with respect to their galling resistance using pin-on-disc testing. The results show that a high galling resistance is favored by a high stainless steel sheet hardness and a blasted stainless steel sheet surface topography. The effect of type of lubricant was found to be more complex. For example, the chlorinated lubricants failed to prevent metal-to-metal contact on a brushed sheet surface but succeeded on a blasted sheet surface of the same stainless steel material. This is believed to be due to a protective tribofilm which is able to form on the blasted surface, but not on the brushed surface.

Trade effects of exchange rate fluctuations: Evidence from Sweden

An overview of the theoretical literature for the last two decades suggests that there is no clear-cut relationship one can pin down between exchange rate volatility and trade flows. Analytical results are based on specific assumptions and only hold in certain cases. Especially, the impact of exchange rate volatility on export and import activity investigated separately leads also to dissimilar conclusions among countries studied. The general presumption is that an increase in exchange rate volatility will have an adverse effect on trade flows and consequently, the overall heath of the world economy. However, neither theoretical models nor empirical studies provide us with a definitive answer, leaving obtained results highly ambiguous and inconsistent (Baum and Caglayan, 2006). We purposed to empirically investigate trade effects of exchange rate fluctuations in Sweden from the perspective of export and import in this research. The data comprises period from January 1993 to December 2006, where export and import volumes are considered from the point of their determinants, including exchange rate volatility, which has been measured through EGARCH model. The results for the case of Sweden show that short run dynamics of volatility negatively associated with both export and import, whereas considered from the case of previous period volatility it exhibits positive relationship. These results are consistent with the most findings of prior studies, where the relationship remained ambiguous.

Acoustic Variability in the Production of English Vowels by Native and Non-Native Speakers

The features of non-native speech which distinguish it from native speech are often difficult to pin down. It is possible to be a native speaker of any of a vast number of varieties of English. These varieties each have their phonetic characteristics which allow them to be identified by speakers of the varieties in question and by others. The phonetic differences between the accents represented by these varieties are very great. It is impossible to indicate any particular configuration of vowels in the acoustic vowel space or set of consonant articulations which all native-speaker varieties of English have in common and which non-native speakers do not share. This study considers the vowel quality in a single word by native and non-native speakers.

Arbetsorganisation i träbränsleeldande fjärrvärmeverk

The objective of this study has been to describe and analyse existing forms of organisation in heating plants using wood fuels, regarding work tasks, organisational structure, skill demands, crew recruitment, working hours and wage conditions. Sixteen plants ranging from 10 to 120 MW have been studied by means of interviews, work place observations and written material. The job of the operator of heating plants is fairly qualified, independent and varied. The most negative factor is shift work. Some of the bigger plants (enterprises) have a relatively hierarchic, segmented and perhaps also an oversized organisation. However, modern concepts of organisation, such as customer orientation, ”flat organisation”, integration of production and maintenance etc, are gaining ground. Blue collar and white collar tasks are increasingly being integrated. Some of the medium sized enterprises have reached very far and may serve as models for bigger enterprises.

Tribological Testing of Some Potential PVD and CVD Coatings for Steel Wire Drawing Dies

Cemented carbide is today the most frequently used drawing die material in steel wire drawing applications. This is mainly due to the possibility to obtain a broad combination of hardness and toughness thus meeting the requirements concerning strength, crack resistance and wear resistance set by the wire drawing process. However, the increasing cost of cemented carbide in combination with the possibility to increase the wear resistance of steel through the deposition of wear resistant CVD and PVD coatings have enhanced the interest to replace cemented carbide drawing dies with CVD and PVD coated steel wire drawing dies. In the present study, the possibility to replace cemented carbide wire drawing dies with CVD and PVD coated steel drawing dies have been investigated by tribological characterisation, i.e. pin-on-disc and scratch testing, in combination with post-test observations of the tribo surfaces using scanning electron microscopy, energy dispersive X-ray spectroscopy and 3D surface profilometry. Based on the results obtained, CVD and PVD coatings aimed to provide improved tribological performance of steel wire drawing dies should display a smooth surface topography, a high wear resistance, a high fracture toughness (i.e. a high cracking and chipping resistance) and intrinsic low friction properties in contact with the wire material. Also, the steel substrate used must display a sufficient load carrying capacity and resistance to thermal softening. Of the CVD and PVD coatings evaluated in the tribological tests, a CVD TiC and a PVD CrC/C coating displayed the most promising results.

Vem är den ekonomiske brottslingen? : En jämförelse mellan länder och brottstyper

Who is the economic criminal? A comparison between countries and types of crime In white collar crime research two particularly competing definitions (Sutherland versus the Revisionists) have dominated the field during the last two decades. Sutherland’s definition states that the sociodemographic profile is homogeneous (entrepreneur with high education and high or regular income), despite type of white collar crime or context. The definition given by the Revisionists states that white collar criminals’ demographic profile is heterogeneous (everyone can be convicted for white collar crime). As a consequence of this divided definitional approach we have a contradictive outcome of who the white collar criminal is. Our purpose is to investigate the qualification of the two definitions by analyzing heterogeneity/ homogeneity based on crime type and national context. The investigation is based on seven countries from the EES 2004 (European Social Survey). We use four types of crime. The results show a rather homogeneous demographic profile but there is also a certain substantial heterogeneity depending on kinds of crime and context. The results altogether indicate that the Revisionists’ definition is more correct in its description of the white collar criminal than Sutherland’s definition. The demographic profile of the white collar criminal seems to be more complex than a profile confined to just one social category would be and the contextual factor has an impact on the variety of the demographic profile. An important task for future research is to hold the door open for further demographic investigations depending on the type of crime and country that the study is based on. 

Mechanical and tribological properties of PVD-coated cemented carbide as evaluated by a new multi-pass scratch testing method

A new test method based on multipass scratch testing has been developed for evaluating the mechanical and tribological properties of thin, hard coatings. The proposed test method uses a pin-on-disc tribometer and during testing a Rockwell C diamond stylus is used as the “pin” and loaded against the rotating coated sample. The influence of normal load on the number of cycles to coating damage is investigated and the resulting coating damage mechanisms are evaluated by posttest scanning electron microscopy. The present study presents the test method by evaluating the performance of Ti0.86Si0.14N, Ti0.34Al0.66N, and (Al0.7Cr0.3)2O3 coatings deposited by cathodic arc evaporation on cemented carbide inserts. The results show that the test method is quick, simple, and reproducible and can preferably be used to obtain relevant data concerning the fatigue, wear, chipping, and spalling characteristics of different coating-substrate composites. The test method can be used as a virtually nondestructive test and, for example, be used to evaluate the fatigue and wear resistance as well as the cohesive and adhesive interfacial strength of coated cemented carbide inserts prior to cutting tests.