Undersökning av steady state och utvärdering av valskraft och friktion vid kallvalsning av aluminium

The purpose with this thesis was to examine the cold rolling mill located at Högskolan Dalarna and to stabilize the rolling process, to achieve steady state. Experiments with cold rolling of an aluminium strip have given results for rolling force, friction, reduction, strip tension and strain hardening. Results show that steady state has been found for the experiments with roll force and strain hardening, and not been found for the experiments with friction and reduction. Results show that increased strip tension gives lower roll forces. The roll force equation of Stone shows comparable results with reality for dry contact with reductions up to 30 %, but starts being incomparable with higher reductions. The roll force equation of Stone shows a bit higher roll forces than reality gave, but was comparable within reductions from 13 to 50 %. Experiments have shown that the aluminium strip has gone through strain hardening. Experiments show how the set roll gap did not yield the desired thickness reduction, there for the elastic spring constant for the rolling mill was examined and determined to be 417 N / mm for the specific alloy band. The influence of tension strip for roll force was examined and Results confirm the theory about how the roll force is decreased by increasing tension strip. The work rolls started to slip against the alumina strip as high tension strip; 70 N/mm2, gave low roll force; < 15kN.

Wear of coated and uncoated PCBN cutting tool used in turning and milling

This licentiate thesis has the main focus on evaluation of the wear of coated and uncoated polycrystalline cubic boron nitride cutting tool used in cutting operations against hardened steel. And to exam the surface finish and integrity of the work material used. Harder work material, higher cutting speed and cost reductions result in the development of harder and more wear resistance cutting tools. Although PCBN cutting tools have been used in over 30 years, little work have been done on PVD coated PCBN cutting tools. Therefore hard turning and hard milling experiments with PVD coated and uncoated cutting tools have been performed and evaluated. The coatings used in the present study are TiSiN and TiAlN. The wear scar and surface integrity have been examined with help of several different characterization techniques, for example scanning electron microscopy and Auger electron spectroscopy.   The results showed that the PCBN cutting tools used displayed crater wear, flank wear and edge micro chipping. While the influence of the coating on the crater and flank wear was very small and the coating showed a high tendency to spalling. Scratch testing of coated PCBN showed that, the TiAlN coating resulted in major adhesive fractures. This displays the importance of understanding the effect of different types of lapping/grinding processes in the pre-treatment of hard and super hard substrate materials and the amount and type of damage that they can create. For the cutting tools used in turning, patches of a adhered layer, mainly consisting of FexOy were shown at both the crater and flank. And for the cutting tools used in milling a tribofilm consisting of SixOy covered the crater. A combination of tribochemical reactions, adhesive wear and mild abrasive wear is believed to control the flank and crater wear of the PCBN cutting tools. On a microscopic scale the difference phases of the PCBN cutting tool used in turning showed different wear characteristics. The machined surface of the work material showed a smooth surface with a Ra-value in the range of 100-200 nm for the turned surface and 100-150 nm for the milled surface. With increasing crater and flank wear in combination with edge chipping the machined surface becomes rougher and showed a higher Ra-value. For the cutting tools used in milling the tendency to micro edge chipping was significant higher when milling the tools steels showing a higher hard phase content and a lower heat conductivity resulting in higher mechanical and thermal stresses at the cutting edge.

Influence of a prudent diet on circulating cathepsin S in humans

BACKGROUND: Increased circulating cathepsin S levels have been linked to increased risk of cardiometabolic diseases and cancer. However, whether cathepsin S is a modifiable risk factor is unclear. We aimed to investigate the effects of a prudent diet on plasma cathepsin S levels in healthy individuals. FINDINGS: Explorative analyses of a randomized study were performed in 88 normal to slightly overweight and hyperlipidemic men and women (aged 25 to 65) that were randomly assigned to ad libitum prudent diet, i.e. healthy Nordic diet (ND) or a control group (habitual Western diet) for 6 weeks. Whereas all foods in the ND were provided, the control group was advised to consume their habitual diet throughout the study. The ND was in line with dietary recommendations, e.g. low in saturated fats, sugars and salt, but high in plant-based foods rich in fibre and unsaturated fats.The ND significantly decreased cathepsin S levels (from 20.1 (+/-4.0 SD) to 19.7 μg/L (+/-4.3 SD)) compared with control group (from 18.2 (+/-2.9 SD) to 19.1 μg/L (+/-3.8 SD)). This difference remained after adjusting for sex and change in insulin sensitivity (P = 0.03), and near significant after adjusting for baseline cathepsin S levels (P = 0.06), but not for change in weight or LDL-C. Changes in cathepsin S levels were directly correlated with change in LDL-C. CONCLUSIONS: Compared with a habitual control diet, a provided ad libitum healthy Nordic diet decreased cathepsin S levels in healthy individuals, possibly mediated by weight loss or lowered LDL-C. These differences between groups in cathepsin S were however not robust and therefore need further investigation.