Performance Evaluation of Different PV-Array Configurations under Weak Light Conditions and Partial Shadings

The paper analyses empirical performance data of five commercial PV-plants in Germany. The purpose was on one side to investigate the weak light performance of the different PV-modules used. On the other hand it was to quantify and compare the shading losses of different PV-array configurations. The importance of this study relies on the fact that even if the behavior under weak light conditions or the shading losses might seem to be a relatively small percentage of the total yearly output; in projects where a performance guarantee is given, these variation can make the difference between meeting or not the conditions.When analyzing the data, a high dispersion was found. To reduce the optical losses and spectral effects, a series of data filters were applied based on the angle of incidence and absolute Air Mass. To compensate for the temperature effects and translate the values to STC (25°C), five different methods were assessed. At the end, the Procedure 2 of IEC 60891 was selected due to its relative simplicity, usage of mostly standard parameters found in datasheets, good accuracy even with missing values, and its potential to improve the results when the complete set of inputs is available.After analyzing the data, the weak light performance of the modules did not show a clear superiority of a certain technology or technology group over the others. Moreover, the uncertainties in the measurements restrictive the conclusiveness of the results.In the partial shading analysis, the landscape mounting of mc-Si PV-modules in free-field showed a significantly better performance than the portrait one. The cross-table string using CIGS modules did not proved the benefits expected and performed actually poorer than a regular one-string-per-table layout. Parallel substrings with CdTe showed a proper functioning and relatively low losses. Among the two product generations of CdTe analyzed, none showed a significantly better performance under partial shadings.

NAVET's Boxes - an Evaluation of the Post-Visit Loan Service at a Science Centre in Borås

Many pedagogues believe science centres to be a good complement to the more formal school teaching. For a visit to a science centre to be as educational as possible, there is a need for pre-visit information of some sort, a guided visit, and post-visit work. Many science centres offer loan services of different kinds. At Navet, a science centre in Borås, teachers can borrow boxes with experiments connected to the different themes they provide. The experiments are supposed to be a continuation of the visit and help settle the knowledge gained during the visit. This thesis is an evaluation of how the boxes function in the schools, and what the teachers think of them. The study was conducted through questionnaires and interviews with both teachers and the staff at Navet. The results of the study are very positive. Many teachers have been involved with Navet from the very beginning and they see a visit to Navet as an integrated part of their teaching. Some boxes work better than others and some might need clearer information, but overall the teachers see the boxes as timesavers, as a way to vary their teaching more easily, and as a help for teachers not specialized in mathematics and science.

Load balancing solution and evaluation of F5 content switch equipment

The Thesis focused on hardware based Load balancing solution of web traffic through a load balancer F5 content switch. In this project, the implemented scenario for distributing HTTPtraffic load is based on different CPU usages (processing speed) of multiple member servers.Two widely used load balancing algorithms Round Robin (RR) and Ratio model (weighted Round Robin) are implemented through F5 load balancer. For evaluating the performance of F5 content switch, some experimental tests has been taken on implemented scenarios using RR and Ratio model load balancing algorithms. The performance is examined in terms of throughput (bits/sec) and Response time of member servers in a load balancing pool. From these experiments we have observed that Ratio Model load balancing algorithm is most suitable in the environment of load balancing servers with different CPU usages as it allows assigning the weight according to CPU usage both in static and dynamic load balancing of servers.

Analysis and Evaluation of EndpointSecurity Solutions

The main objective for this degree project was to analyze the Endpoint Security Solutions developed by Cisco, Microsoft and a third minor company solution represented by InfoExpress. The different solutions proposed are Cisco Network Admission Control, Microsoft Network Access Protection and InfoExpress CyberGatekeeper. An explanation of each solution functioning is proposed as well as an analysis of the differences between those solutions. This thesis work also proposes a tutorial for the installation of Cisco Network Admission Control for an easier implementation. The research was done by reading articles on the internet and by experimenting the Cisco Network Admission Control solution. My background knowledge about Cisco routing and ACL was also used. Based on the actual analysis done in this thesis, a conclusion was drawn that all existing solutions are not yet ready for large-scale use in corporate networks. Moreover all solutions are proprietary and incompatible. The future possible standard for Endpoint solution might be driven by Cisco and Microsoft and a rude competition begins between those two giants.

Evaluation of surface treatment techniques for polypropylene andimplementation of a method for testing ink adhesion

If a plastic material is used as a print bearer there are a need of a special surface treatment to get agod and durable printing. The most used surface treatment technique for the moment is coronatreatment. This kind of treatment has unfortunately showed not to be so durable in the long term.Plasma treatment which in this case uses different kind of gases in the treatment of polypropyleneis shown as a more effective treatment in this project. When the plasma treated surface has beenprinted is the good quality last much longer and the adhesion between the ink and the surface isremained. To test this adhesion is for the moment a standard used (ASTM D3359). This standardhas appeared unstable and dependent at many different factors, which gives a big variation in thetest results. Because of this has new test methods been carried out to give a more even and morereliable result in the test of the adhesion.

QoS Evaluation of BandwidthSchedulers in IPTV Networks OfferedSRD Fluid Video Traffic

Internet protocol TV (IPTV) is predicted to be the key technology winner in the future. Efforts to accelerate the deployment of IPTV centralized model which is combined of VHO, encoders, controller, access network and Home network. Regardless of whether the network is delivering live TV, VOD, or Time-shift TV, all content and network traffic resulting from subscriber requests must traverse the entire network from the super-headend all the way to each subscriber's Set-Top Box (STB).IPTV services require very stringent QoS guarantees When IPTV traffic shares the network resources with other traffic like data and voice, how to ensure their QoS and efficiently utilize the network resources is a key and challenging issue. For QoS measured in the network-centric terms of delay jitter, packet losses and bounds on delay. The main focus of this thesis is on the optimized bandwidth allocation and smooth datatransmission. The proposed traffic model for smooth delivering video service IPTV network with its QoS performance evaluation. According to Maglaris et al [5] First, analyze the coding bit rate of a single video source. Various statistical quantities are derived from bit rate data collected with a conditional replenishment inter frame coding scheme. Two correlated Markov process models (one in discrete time and one incontinuous time) are shown to fit the experimental data and are used to model the input rates of several independent sources into a statistical multiplexer. Preventive control mechanism which is to be include CAC, traffic policing used for traffic control.QoS has been evaluated of common bandwidth scheduler( FIFO) by use fluid models with Markovian queuing method and analysis the result by using simulator andanalytically, Which is measured the performance of the packet loss, overflow and mean waiting time among the network users.

Evaluation of galling resistance for some selected combinations of tool steels/stainless steel sheet materials/lubricants using pin-on-disc testing

Stainless steels are well known to be prone to cold welding and material transfer in sliding contacts and therefore difficult to cold form unless certain precautions as discussed in this paper are taken. In the present study different combinations of tool steels/stainless steels/lubricants has been evaluated with respect to their galling resistance using pin-on-disc testing. The results show that a high galling resistance is favored by a high stainless steel sheet hardness and a blasted stainless steel sheet surface topography. The effect of type of lubricant was found to be more complex. For example, the chlorinated lubricants failed to prevent metal-to-metal contact on a brushed sheet surface but succeeded on a blasted sheet surface of the same stainless steel material. This is believed to be due to a protective tribofilm which is able to form on the blasted surface, but not on the brushed surface.

QoS evaluation of Bandwidth Schedulers in IPTV Networks Offered SRD Fluid Video Traffic

Internet protocol TV (IPTV) is predicted to be the key technology winner in the future. Efforts to accelerate the deployment of IPTV centralized model which is combined of VHO, encoders, controller, access network and Home network. Regardless of whether the network is delivering live TV, VOD, or Time-shift TV, all content and network traffic resulting from subscriber requests must traverse the entire network from the super-headend all the way to each subscriber's Set-Top Box (STB). IPTV services require very stringent QoS guarantees When IPTV traffic shares the network resources with other traffic like data and voice, how to ensure their QoS and efficiently utilize the network resources is a key and challenging issue. For QoS measured in the network-centric terms of delay jitter, packet losses and bounds on delay. The main focus of this thesis is on the optimized bandwidth allocation and smooth data transmission. The proposed traffic model for smooth delivering video service IPTV network with its QoS performance evaluation. According to Maglaris et al [5] first, analyze the coding bit rate of a single video source. Various statistical quantities are derived from bit rate data collected with a conditional replenishment inter frame coding scheme. Two correlated Markov process models (one in discrete time and one in continuous time) are shown to fit the experimental data and are used to model the input rates of several independent sources into a statistical multiplexer. Preventive control mechanism which is to be including CAC, traffic policing used for traffic control. QoS has been evaluated of common bandwidth scheduler( FIFO) by use fluid models with Markovian queuing method and analysis the result by using simulator and analytically, Which is measured the performance of the packet loss, overflow and mean waiting time among the network users.

Energy Efficiency through Thermal Energy Storage - Evaluation of the Possibilities for the Swedish Building Stock, Phase 1

As a first step in assessing the potential of thermal energy storage in Swedish buildings, the current situation of the Swedish building stock and different storage methods are discussed in this paper. Overall, many buildings are from the 1960’s or earlier having a relatively high energy demand, creating opportunities for large energy savings. The major means of heating are electricity for detached houses and district heating for multi dwelling houses and premises. Cooling needs are relatively low but steadily increasing, emphasizing the need to consider energy storage for both heat and cold. The thermal mass of a building is important for passive storage of thermal energy but this has not been considered much when constructing buildings in Sweden. Instead, common ways of storing thermal energy in Swedish buildings today is in water storage tanks or in the ground using boreholes, while latent thermal energy storage is still very uncommon.

Thermal Evaluation of a Solarus PV-T collector

Low concentrator PV-T hybrid systems produce both electricity and thermal energy; this fact increases the overall efficiency of the system and reduces the cost of solar electricity. These systems use concentrators which are optical devices that concentrate sunlight on to solar cells and reduce expensive solar cell area. This thesis work deals with the thermal evaluation of a PV-T collector from Solarus.Firstly the thermal efficiency of the low concentrator collector was characterized for the thermal-collector without PV cells on the absorber. Only two types of paint were on the absorber, one for each trough of the collector. Both paints are black one is glossy and the other is dull,. The thermal efficiency at no temperature difference between collector and ambient for these two types of paint was 0.65 and 0.64 respectively; the U-value was 8.4 W/m2°C for the trough with the glossy type of paint and 8.6 W/m2°C for the trough with dull type of paint. The annual thermal output of these two paints was calculated for two different geographic locations, Casablanca, Morocco and Älvkarleby, Sweden.Secondly the thermal efficiency was defined for the PV-T collector with PV cells on the absorber. The PV cells cover 85% of the absorber, without any paint on the rest of the absorber area. We also tested how the electrical power output influences the thermal power output of the PV-T collector. The thermal and total performances for the PV-T collector were only characterized with reflector sides, because of the lack of time we could not characterize them with transparent sides also.

Electrical Evaluation of a Low Concentrating PVT Collector Based on Performance Ratio

Photovoltaic Thermal/Hybrid collectors are an emerging technology that combines PV and solar thermal collectors by producing heat and electricity simultaneously. In this paper, the electrical performance evaluation of a low concentrating PVT collector was done through two testing parts: power comparison and performance ratio testing. For the performance ratio testing, it is required to identify and measure the factors affecting the performance ratio on a low concentrating PVT collector. Factors such as PV cell configuration, collector acceptance angle, flow rate, tracking the sun, temperature dependence and diffuse to irradiance ratio. Solarus low concentrating PVT collector V12 was tested at Dalarna University in Sweden using the electrical equipment at the solar laboratory. The PV testing has showed differences between the two receivers. Back2 was producing 1.8 energy output more than Back1 throughout the day. Front1 and Front2 were almost the same output performance. Performance tests showed that the cell configuration for Receiver2 with cells grouping (6- 32-32-6) has proved to have a better performance ratio when to it comes to minimizing the shading effect leading to more output power throughout the day because of lowering the mismatch losses. Different factors were measured and presented in this thesis in chapter 5. With the current design, it has been obtained a peak power at STC of 107W per receiver. The solar cells have an electrical efficiency of approximately 19% while the maximum measured electrical efficiency for the collector was approximately 18 % per active cell area, in addition to a temperature coefficient of -0.53%/ ˚C. Finally a recommendation was done to help Solarus AB to know how much the electrical performance is affected during variable ambient condition and be able to use the results for analyzing and introducing new modification if needed.

PANA V : Evaluation of a Literacy Project

PANA V Evaluation of a Literacy ProjectSUMMARY AND CONCLUSIONSThis evaluation set out to explore the impact of the literacy work carried out through PANA V. It focussed on clarifying effects such as empowerment and poverty reduction in relation to the civil society. Two specific objectives were to evaluate the methodological approach and the didactic materials and to evaluate the sustainability of the project.Although the focus of the evaluation has been PANA V, the project has been evaluated in its context, as one in a series of five projects located in Rwanda ten years after the war and genocide. The conclusion will consider future plans in this field.The evaluator has striven to create a holistic picture of the effects of the project, although the given time for the evaluation was short. Only three weeks were spent in the field study and only ten days in the actual field. Although there were some organisational and logistic problems, as is common when carrying out a study like this in a poor country, many literacy sites were visited and quite many participators were interviewed. The overall impression from the study is overwhelmingly positive. So many people commit themselves in this task of teaching Rwandans reading, writing and numeracy. Despite harsh conditions learners strive to learn and group leaders devote themselves to the task. Many leaders on different levels try their very best to manage their difficult and demanding task. The main objective was to explore the impact of the project on poverty reduction, particularly on empowerment and strategies for everyday life. Women were to be regarded particularly. From the results it is clear that the project has a strong, positive impact both on poverty reduction and empowerment of marginalised groups. Among those who have benefited from the alphabetisation are mainly women. Unfortunately, when it comes to leaders in PANA, who may also be said to have benefited from the project, only a small minority is women. This is something that is recommended that it be reconsidered inside the organisation. As a majority of the targeted learners are women, and as the economic and social situation of women in Rwanda is generally weak, this is a question that I recommend the Pentesostal church and ADEPR to look particularly into. With many women being single breadwinners of their households, it is important that also women get access to positions that may bring benefits of different kind.It is also clear that the project has positive effects for the civil society. In the present situation in Rwanda, during the process of reconciliation and rapid progress, basic education for the poor majority is a democratic issue. In a country with a plethora of internet-cafés in the capital and a small minority that use cars and mobile-telephones to communicate nation-wide, it is of outmost importance that the majority acquires basic education, of which literacy is a central part. To strengthen the civil society in Rwanda literacy is important. One central issue is then that Rwanda develops toward becoming a country where literacy is used for the benefit of the citizens and it is a democratic issue that all citizens get an opportunity to participate. Crucial for this is that strong efforts are put into primary schools nation-wide. Literacy projects for adults, like PANA, may only complement these efforts, but they constitute important and necessary complements. Other relevant ways to promote literacy are campaigns in Radio and TV and through cultural events such as festivals, music and theatre. News papers, magazines and books are natural parts of such campaigns as well as adult education. As stated under the results not much can be said about the didactics in this evaluation. On the whole the methodology and the materials fill their function well and receive a high reputation. As people learn to read and write under very simple conditions, obviously the approach is appropriate. A few suggestions may be given from the study:•Focus groups leaders’ attention on clearness, that they show very clearly what is to be read. Good structuring is probably of great importance for many learners.•Make clear what is tested in the tests and consider the possibility to use a holistic test that would be more congruent with the methodology. The possibility to use only one grade, pass, would enable a more practical test, such as reading a short, relevant text, writing something relevant and solving practical mathematic problems. Avoid tests that demand school knowledge.•Avoid using methaphors such as “fight against illiteracy” and connections between illiteracy/literacy and darkness/light. It is not true that illiteracy causes bad things and that literacy only brings good. •Be prepared that it may be more difficult in the future to achieve the goals as it may be the case that the early learners where the ones who achieved easily. The goal of “literacy in six month” in PANA will probably hold only for some learners but also those who do not manage in six months need literacy skills.A third objective was to secure sustainability. As for sustainability of the project in itself, and of the literacy process, the main conclusion is that there is a good potential. The commitment and devotedness among many involved in PANA proves good. One weakness is individual leaders in ADEPR who do not see this as an important task for the Pentecostal church in Rwanda. Other weaknesses are the unwillingness to mention explicitly the wish, for example among group leaders, to get some kind of incentive and the fear of loosing believers by cooperation with other organisations. A higher degree of transparency in this issue would probably solve some irritations and tensions.As for the sustainability of the literacy skills much may be done to improve. The acquired skills seem to be comparably relevant. The level achieved, and the level tested, may be defined as basic literacy skills, consisting of basic reading, writing and numeracy skills. However, these skills are very restricted and there is a high risk that the skills will decline, which means that there is a high risk that people will forget how to read and write because of lack of exercising. From these conclusions a few suggestions for future development will be given.

Benchmark Evaluation of HOG Descriptors as Features for Classification of Traffic Signs

The purpose of this paper is to analyze the performance of the Histograms of Oriented Gradients (HOG) as descriptors for traffic signs recognition. The test dataset consists of speed limit traffic signs because of their high inter-class similarities.   HOG features of speed limit signs, which were extracted from different traffic scenes, were computed and a Gentle AdaBoost classifier was invoked to evaluate the different features. The performance of HOG was tested with a dataset consisting of 1727 Swedish speed signs images. Different numbers of HOG features per descriptor, ranging from 36 features up 396 features, were computed for each traffic sign in the benchmark testing. The results show that HOG features perform high classification rate as the Gentle AdaBoost classification rate was 99.42%, and they are suitable to real time traffic sign recognition. However, it is found that changing the number of orientation bins has insignificant effect on the classification rate. In addition to this, HOG descriptors are not robust with respect to sign orientation.