A GUI for online presentation of steel and steelmaking ladle temperature data and simulation.

Continuous casting is a casting process that produces steel slabs in a continuous manner with steel being poured at the top of the caster and a steel strand emerging from the mould below. Molten steel is transferred from the AOD converter to the caster using a ladle. The ladle is designed to be strong and insulated. Complete insulation is never achieved. Some of the heat is lost to the refractories by convection and conduction. Heat losses by radiation also occur. It is important to know the temperature of the melt during the process. For this reason, an online model was previously developed to simulate the steel and ladle wall temperatures during the ladle cycle. The model was developed as an ODE based model using grey box modeling technique. The model’s performance was acceptable and needed to be presented in a user friendly way. The aim of this thesis work was basically to design a GUI that presents steel and ladle wall temperatures calculated by the model and also allow the user to make adjustments to the model. This thesis work also discusses the sensitivity analysis of different parameters involved and their effects on different temperature estimations.

Photovoltaic Process Development and innovative Techniques

Photovoltaic processing is one of the processes that have significance in semiconductor process line. It is complicated due to the no. of elements involved that directly or indirectly affect the processing and final yield. So mathematically or empirically we can’t say assertively about the results specially related with diffusion, antireflective coating and impurity poisoning. Here I have experimented and collected data on the mono-crystal silicon wafers with varying properties and outputs. Then by using neural network with available experimental data output required can be estimated which is further tested by the test data for authenticity. One can say that it’s a kind of process simulation with varying input of raw wafers to get desired yield of photovoltaic mono-crystal cells.

Survery and simulation of energy use in the European building stock

the work towards increased energy efficiency. In order to plan and perform effective energy renovation of the buildings, it is necessary to have adequate information on the current status of the buildings in terms of architectural features and energy needs. Unfortunately, the official statistics do not include all of the needed information for the whole building stock.   This paper aims to fill the gaps in the statistics by gathering data from studies, projects and national energy agencies, and by calibrating TRNSYS models against the existing data to complete missing energy demand data, for countries with similar climate, through simulation. The survey was limited to residential and office buildings in the EU member states (before July 2013). This work was carried out as part of the EU FP7 project iNSPiRe.   The building stock survey revealed over 70% of the residential and office floor area is concentrated in the six most populated countries. The total energy consumption in the residential sector is 14 times that of the office sector. In the residential sector, single family houses represent 60% of the heated floor area, albeit with different share in the different countries, indicating that retrofit solutions cannot be focused only on multi-family houses.   The simulation results indicate that residential buildings in central and southern European countries are not always heated to 20 °C, but are kept at a lower temperature during at least part of the day. Improving the energy performance of these houses through renovation could allow the occupants to increase the room temperature and improve their thermal comfort, even though the potential for energy savings would then be reduced.

Manoeuvring between anxiety and control : Patients experience of learning to live with diabetes: a lifeworld phenomenological study

Research shows that people with diabetes want their lives to proceed as normally as possible, but some patients experience difficulty in reaching their desired goals with treatment. The learning process is a complex phenomenon interwoven into every facet of life. Patients and healthcare providers often have different perspectives in care which gives different expectations on what the patients need to learn and cope with. The aim of this study, therefore, is to describe the experience of learning to live with diabetes. Interviews were conducted with 12 patients afflicted with type 1 or type 2 diabetes. The interviews were then analysed with reference to the reflective lifeworld research approach. The analysis shows that when the afflicted realize that their bodies undergo changes and that blood sugar levels are not always balanced as earlier in life, they can adjust to their new conditions early. The afflicted must take responsibility for balancing their blood sugar levels and incorporating the illness into their lives. Achieving such goals necessitates knowledge. The search for knowledge and sensitivity to changes are constant requirements for people with diabetes. Learning is driven by the tension caused by the need for and dependence on safe blood sugar control, the fear of losing such control, and the fear of future complications. The most important responsibilities for these patients are aspiring to understand their bodies as lived bodies, ensuring safety and security, and acquiring the knowledge essential to making conscious choices.