Flavor characterization of sugar-added pennywort (Centella asiatica L.) juices treated with ultra-high pressure and thermal processes

The flavor characteristics of pennywort juices with added sugar treated by ultra-high pressure, pasteurization, and sterilization were investigated using solid phase microextraction combined with gas chromatography-mass spectrometry. It was found that sesquiterpene hydrocarbons comprised the major class of volatile components present and the juices had a characteristic aroma due to the presence of volatiles including beta-caryophyllene and humulene and alpha-copaene. In comparison with heated juices, HPP-treated samples could retain more volatile compounds such as linalool and geraniol similar to those present in fresh juice, whereas some volatiles such as alpha-terpinene and ketone class were apparently formed by thermal treatment. All processing operations produced juice that was not significantly different in the concentration of total volatiles. Practical Application: Pennywort juice is considered a nutraceutical drink for health benefits. Therefore, to preserve all aroma and active components in this juice, a nonthermal process such as ultra-high pressure should be a more appropriate technique for retention of its nutritive values than pasteurization and sterilization.

Effects of hydrocolloid addition and high pressure processing on the rheological properties and microstructure of a commercial ostrich meat product "Yor" (Thai sausage)

"Yor" is a traditional sausage like product widely consumed in Thailand. Its textures are usually set by steaming, in this experiment ultra-high pressure was used to modify the product. Three types of hydrocolloid; carboxymethylcellulose (CMC), locust bean gum (LBG) and xanthan gum, were added to minced ostrich meat batter at concentration of 0-1% and subjected to high pressure 600 Mpa, 50 degrees C, 40 min. The treated samples were analysed for storage (G) and loss (G '') moduli by dynamic oscillatory testing as well as creep compliance for control stress measurement. Their microstructures using confocal microscopy were also examined. Hydrocolloid addition caused a significant (P < 0.05) decrease in both the G' and G '' moduli. However the loss tangent of all samples remained unchanged. Addition of hydrocolloids led to decreases in the gel network formation but appears to function as surfactant materials during the initial mixing stage as shown by the microstructure. Confocal microscopy suggested that the size of the fat droplets decreased with gum addition. The fat droplets were smallest on the addition of xanthan gum and increased in the order CMC, LBG and no added gum, respectively. Creep parameters of ostrich yors with four levels of xanthan gum addition (0.50%, 0.75%, 1.00% and 1.25%) showed an increase in the instantaneous compliance (J(0)), the retarded compliance (J(1)) and retardation time (lambda(1)) but a decrease in the viscosity (eta(0)) with increasing levels of addition. The results also suggested that the larger deformations used during creep testing might be more helpful in assessing the mechanical properties of the product than the small deformations used in oscillatory rheology. (c) 2007 Elsevier Ltd. All rights reserved.

Effect of combined heat and high-pressure treatments on the texture of chicken breast muscle (Pectoralis fundus)

Commercially supplied chicken breast muscle was subjected to simultaneous heat and pressure treatments. Treatment conditions ranged from ambient temperature to 70 °C and from 0.1 to 800 MPa, respectively, in various combinations. Texture profile analysis (TPA) of the treated samples was performed to determine changes in muscle hardness. At treatment temperatures up to and including 50 °C, heat and pressure acted synergistically to increase muscle hardness. However, at 60 and 70 °C, hardness decreased following treatments in excess of 200 MPa. TPA was performed on extracted myofibrillar protein gels that after treatment under similar conditions revealed similar effects of heat and pressure. Differential scanning calorimetry analysis of whole muscle samples revealed that at ambient pressure the unfolding of myosin was completed at 60 °C, unlike actin, which completely denatured only above 70 °C. With simultaneous pressure treatment at >200 MPa, myosin and actin unfolded at 20 °C. Unfolding of myosin and actin could be induced in extracted myofibrillar protein with simultaneous treatment at 200 MPa and 40 °C. Electrophoretic analysis indicated high pressure/temperature regimens induced disulfide bonding between myosin chains.

High-pressure structural studies of the pharmaceutical, chlorothiazide

The pharmaceutical material chlorothiazide (6-chloro-4H-1,2,4-benzothiadiazine-7-sulfonamide 1,1-dioxide) has been studied under high-pressure conditions using single-crystal and powder X-ray diffraction. An isosymmetric phase transition to a second polymorph occurs at 4.4 GPa. An analysis of the structural changes that occur during this phase transition has been performed.

endo-Selective (3+2) cycloaddition polymerizations of nitrone monomers with olefins utilising high pressure conditions

A high pressure mediated (3+2) cycloaddition polymerization strategy has been employed to afford linear poly(isoxazolidine) architectures. Under these high pressure conditions this cycloaddition process was found to afford primarily endoheterocycles which when translated to the polymerization should ultimately affect the tacticity and resultant properties of the polymer. The stereoselectivity occurred as a result of a lower volume of activation for the endo-transition state and the application of a 'type-I' regime (HOMODipole-LUMODipolarophile) cycloaddition process that features secondary orbital interactions within the extended molecular orbitals. A variety of linker segments were employed in an attempt to affect the physical properties of the polymeric cycloadducts such as T-g and solubility in order to tailor these materials for use in coating applications. (C) 2007 Elsevier Ltd. All rights reserved.

Towards the total synthesis of colletofragarones: constructing the macrocyclic lactone by high pressure-mediated intramolecular Diels-Alder reaction

We report herein an intramolecular Diels-Alder approach towards the construction of the macrocyclic lactone ring and the perhydrobenzofuran system of the colletofragarones, novel metabolites produced by fungi of the genus Colletotrichum that are responsible for inhibition of germination of the conidia in these species. Crown Copyright (C) 2009 Published by Elsevier Ltd. All rights reserved.

Predictions of some product parameters based on the processing conditions of ultra-high-temperature milk plants

The temperature-time profiles of 22 Australian industrial ultra-high-temperature (UHT) plants and 3 pilot plants, using both indirect and direct heating, were surveyed. From these data, the operating parameters of each plant, the chemical index C*, the bacteriological index B* and the predicted changes in the levels of beta-lactoglobulin, alpha-lactalbumin, lactulose, furosine and browning were determined using a simulation program based on published formulae and reaction kinetics data. There was a wide spread of heating conditions used, some of which resulted in a large margin of bacteriological safety and high chemical indices. However, no conditions were severe enough to cause browning during processing. The data showed a clear distinction between the indirect and direct heating plants. They also indicated that degree of denaturation of alpha-lactalbumin varied over a wide range and may be a useful discriminatory index of heat treatment. Application of the program to pilot plants illustrated its value in determining processing conditions in these plants to simulate the conditions in industrial UHT plants. (C) 2008 Elsevier Ltd. All rights reserved.

Effects of high pressure on functional properties of soy protein

Simultaneous measurement of the effects of low soy protein concentration, pH and high pressure treatment at room temperature on solubility, emulsifying properties and rheological properties (loss modulus, G '') of soy protein isolate (SPI) were evaluated. Central composite rotatable designs (2(3)) were employed over two pH ranges (2.66-4.34 and 5.16-6.84) with SPI concentration (0.32-3.68%) and pressure (198-702 MPa) as the other independent variables. The surface responses were obtained for protein solubility, emulsifying activity index (EAI) and G ''. The samples with the highest effect on protein solubility, EAI and G '' values were evaluated, as well, by electrophoresis and free sulphydryl determination. The pH was the main factor that affected protein solubility, with solubility at a maximum at pH < 3 or pH > 6. Increasing SPI concentration and decreasing/increasing the pH away from the isoelectric point both caused a reduction in EAI. Loss modulus (G '') was found to increase with SPI concentration in both pH ranges. (c) 2006 Elsevier Ltd. All rights reserved.

Viscoelastic properties of high pressure and heat induced tofu gels

Tofu gels were rheologically examined to determine their storage or elastic (G′) and loss or viscous (G″) moduli as a function of frequency within their linear viscoelastic limits. The tofu gels were made using either glucono-δ-lactone (GDL) or calcium sulphate (CaSO4·2H2O), followed by either heat treatment (heated soymilk at 97 °C prior to coagulation and subsequently held at 70 °C for 60 min, HT) or high pressure treatment (400 MPa at 20 °C for 10 min, HP). The overall moduli values of the GDL gels and CaSO4·2H2O gels of both physical treatments were similar, each gave frequency profiles expected for weak viscoelastic materials. However, although both temperature and high pressure treatments could be used to produce tofu gels, the final products were not the same. Pressure formed gels, despite having a higher overall “consistency” (increasing values of their moduli), had a proportionately higher contribution from the loss modulus (increased tan δ). Differences could also be observed using confocal scanning laser microscopy. While such treatment may give rise to differing systems/structures, with new or modified organoleptic properties, the more “open” structures obtained by pressure treatment may well cause processing difficulties if subsequent reworking or moulding is required.

Viscoelastic properties of high pressure and heat induced tofu gels

Tofu gels were rheologically examined to determine their storage or elastic (G') and loss or viscous (G '') moduli as a function of frequency within their linear viscoelastic limits. The tofu gels were made using either glucono-delta-lactone (GDL) or calcium sulphate (CaSO4 center dot 2H(2)O), followed by either heat treatment (heated soymilk at >= 97 degrees C prior to coagulation and subsequently held at 70 degrees C for 60 min, HT) or high pressure treatment (400 MPa at 20 degrees C for 10 min, HP). The overall moduli values of the GDL gels and CaSO4 center dot 2H(2)O gels of both physical treatments were similar, each gave frequency profiles expected for weak viscoelastic materials. However, although both temperature and high pressure treatments could be used to produce tofu gels, the final products were not the same. Pressure formed gels, despite having a higher overall "consistency" (increasing values of their moduli), had a proportionately higher contribution from the loss modulus (increased tan delta). Differences could also be observed using confocal scanning laser microscopy. While such treatment may give rise to differing systems/structures, with new or modified organoleptic properties, the more "open" structures obtained by pressure treatment may well cause processing difficulties if subsequent reworking or moulding is required. (c) 2007 Elsevier Ltd. All rights reserved.

Opportunities and challenges in high pressure processing of foods

Consumers increasingly demand convenience foods of the highest quality in terms of natural flavor and taste, and which are freedom additives and preservatives. This demand has triggered the need for the development of a number of nonthermal approaches to food processing, of which high-pressure technology has proven to be very valuable. A number of recent publications have demonstrated novel and diverse uses of this technology. Its novel features, which include destruction of microorganisms at room temperature or lower, have made the technology commerically attractive. Enzymes forming bacteria can be by the application of pressure-thermal combinations. This review aims to identify the opportunities and challenges associated with this technology. In addition to discussing the effects of high pressure on food components, this review covers the combined effects of high pressure processing with: gamma irradiation, alternating current, ultrasound, and carbon dioxide or anti-microbial treatment. Further, the applications of this technology in various sectors-fruits and vegetables, dairy and meat processing-have been dealt with extensively. The integration of high-pressure with other matured processing operations such as blanching, dehydration, osmotic dehydration, rehyrdration, frying, freezing/thawing and solid-liquid extraction has been shown to open up new processing options. The key challenges identified include: heat transfer problems and resulting non-uniformity in processing, obtaining reliable and reproducible data, for process validation, lack of detailed knowledge about the interaction between high pressure, and a number of food constituents, packaging and statutory issues.

Effects of combined high-pressure and heat treatment on the textural properties of soya gels

sSPI, 7S, and 11S globulin at 12% (w/v) protein concentration, at neutral pH, did not form gels when heat-treated (90 degreesC, 15 min) or when high pressure-treated (300-700 MPa), except for the I IS, which formed a gel when heat-treated. The combination of heat and pressure (that is heating the solutions in a water bath and then pressure-treating at room temperature or the reverse sequence), led to differences: when heat-treatment was before high-pressure treatment, only the I IS fraction formed a self-standing gel; however, when the solutions were pressurised before heat treatment, all the proteins formed self-standing gels. The textural and water-holding properties were measured on the gels formed with the three different soy proteins. (C) 2002 Elsevier Science Ltd. All rights reserved.