Peroxydisulfate in MCM-48 silicas: powerful and clean materials for the removal of toxic gases

Sodium persulfate introduced into ordered MCM-48 silicas is described. The resulting materials are compared with existing activated carbon-based systems and MCM-48 containing transition metals such as Cu(II) and Cr(VI) for the decomposition of hydrogen cyanide and cyanogen. MCM-48 materials containing sodium persulfate alone improve on the protection offered by benchmark activated carbon systems and MCM-48 materials containing Cu(II) and Cr(VI), without the health risks associated with these metal ions.

Influence of encapsulation and coating materials on the survival of Lactobacillus plantarum and Bifidobacterium longum in fruit juices

The aim of this work was to compare alginate and pectin beads for improving the survival of Lactobacillus plantarum and Bifidobacterium longum during storage in pomegranate and cranberry juice, and to evaluate the influence of various coating materials, including chitosan, gelatin and glucomannan on cell survival and on the size and hardness of the beads. In pomegranate juice, free cells of L. plantarum died within 4 weeks of storage and those of B. longum within 1 week; in cranberry juice both types of cells died within one week. Encapsulation within either alginate or pectin beads improved cell survival considerably, but coating of the beads with chitosan or gelatin improved it even further; coating with glucomannan did not have any positive effect. The double gelatin coated pectin beads gave the highest protection among all types of beads, as a final concentration of approximately 108 CFU/mL and 106 CFU/mL for both L. plantarum and B. longum was obtained after 6 weeks of storage in pomegranate and cranberry juice, respectively. The good protection could be attributed to the very strong interaction between the two polymers, as measured by turbidity experiments, leading to the formation of a polyelectrolyte complex. It was also shown that the coating was able to inhibit the penetration of gallic acid within the beads, which was used in this study as a model phenolic compound with antimicrobial activity; this is a likely mechanism through which the beads were able to protect the cells from the antimicrobial activity of phenolic compounds present in both types of juices. Despite their good protective effect, the pectin beads were considerably softer than the alginate beads, an issue that should be addressed in order to increase their mechanical stability.

Investigation of tin-based alternatives for cadmium in optoelectronic thin-films materials

Increasing legislation has steadily been introduced throughout the world to restrict the use of heavy metals, particularly cadmium (Cd) and lead (Pb) in high temperature pigments, ceramics, and optoelectronic material applications. Removal of cadmium from thin-film optical and semiconductor device applications has been hampered by the absence of viable alternatives that exhibit similar properties with stability and durability. We describe a range of tin-based compounds that have been deposited and characterized in terms of their optical and mechanical properties and compare them with existing cadmium-based films that currently find widespread use in the optoelectronic and semiconductor industries. (c) 2008 Optical Society of America.

Preliminary results from the infrared multilayer filters and materials exposed to the space environment on the NASA LDEF mission

With continually increasing demands for improvements to atmospheric and planetary remote-sensing instrumentation, for both high optical system performance and extended operational lifetimes, an investigation to access the effects of prolonged exposure of the space environment to a series of infrared interference filters and optical materials was promoted on the NASA LDEF mission. The NASA Long Duration Exposure Facility (LDEF) was launchd by the Space Shuttle to transport various science and technology experiments both to and from space, providing investigators with the opportunity to study the effects of the space environment on materials and systems used in space-flight applications. Preliminary results to be discussed consist of transmission measurements obtained and processed from an infrared spectrophotometer both before (1983) and after (1990) exposure compared with unexposed control specimens, together with results of detailed microscopic and general visual examinations performed on the experiment. The principle lead telluride (PbTe) and Zinc Sulphide (ZnS) based multilayer filters selected for this preliminary investigation consist of : an 8-12µm low pass edge filter, a 10.6µm 2.5% half bandwidth (HBW) double half-wave narrow bandpass filter, and a 10% HBW triple half-wave wide bandpass filter at 15µm. Optical substrates of MgF2 and KRS-5 (T1BrI) will also be discussed.

Cooled Infrared Dichroic Beamsplitters and Filters for the MIRI Spectrometer and Imager (5-29µm)

The spectral design and fabrication of cooled (7K) mid-infrared dichroic beamsplitters and bandpass filter coatings for the MIRI spectrometer and imager are described. Design methods to achieve the spectral performance and coating materials are discussed.

Growth, yield and development of strawberry cv. 'Elsanta' under novel photoselective film clad greenhouses

Film greenhouse claddings are typically used to protect horticultural crops from low temperature and high rainfall conditions. However, a range of novel plastic films have been developed which filter specific radiation wavelengths with the aim of providing the grower with greater control of crop growth and development. A replicated experiment was conducted in 8 small experimental greenhouses, covered with different photoselective films characterised by a range of red/far-red ratios and PAR transmissions to study their effects on the growth, yield and quality of the strawberry cv. 'Elsanta'. Marketable yield per plant was 51% greater under the film with the highest light transmission (control) compared with the lower light transmission films. Similarly, unmarketable fruit number and average non-marketable individual fruit weight per plant was lowest under films with higher light transmissions and higher under lower light transmission films. Cropping duration was longer under films with high R/FR. Also plants under high R/FR were more compact (due to shorter petiole lengths) compared to plants grown under low R/FR. The results are discussed in relation to the increased use of photoselective films in protected horticulture and the need for higher quality fruit and vegetables.

Ordering in thin films of block copolymers: fundamentals to potential applications

The ordering of block copolymers in thin films is reviewed, starting, from the fundamental principles and extending to recent promising developments as templates for nanolithography which may find important applications in the semiconductor industry. Ordering in supported thin films of symmetric and asymmetric AB diblock and ABA triblock copolymers is discussed, along with that of more complex materials such as ABC triblocks and liquid crystalline block copolymers Techniques to prepare thin films, and to characterise ordering within them, are summarized. Several methods to align Hock copolymer nanostructures, important in several applications are outlined A number of potential applications in nanolithography, production of porous materials, templating. and patterning of organic and inorganic materials are then presented. The influence of crystallization on the morphology of a block copolymer film is briefly discussed, as are structures in grafted block copolymer films. (C) 2009 Elsevier Ltd All rights reserved.

The trapping and decomposition of toxic gases such as hydrogen cyanide using modified mesoporous silicates

Selected silicas were modified with the covalently bound ligand 2,6-bis(benzoxazoyl)pyridine (BBOP), equilibrated with copper(II) nitrate, then challenged with toxic vapour containing HCN (8000 mg m(-3) at 80% relative humidity). The modified SBA-15 material (Cu-BBOP-SBA-15) had an improved breakthrough time for HCN (36 min at a flow rate of 30 cm(3) min(-1)) when compared to the other siliceous materials prepared in this study, equating to a hydrogen cyanide capacity of 58 mg g(-1), which is close to a reference activated carbon adsorbent (24 min at 50 cm(3) min(-1)) that can trap 64 mg g(-1). The enhanced performance observed with Cu-BBOP-SBA-15 has been related to the greater accessibility of the functional groups, arising from the ordered nature of the interconnected porous network and large mesopores of 5.5 nm within the material modified with the Cu(II)-BBOP complex. Modified MCM-41 and MCM-48 materials (Cu-BBOP-MCM-41 and Cu-BBOP-MCM-48) were found to have lower hydrogen cyanide capacities (38 and 32 mg g(-1) respectively) than the Cu-BBOP-SBA-15 material owing to the restricted size of the pores (2.2 and <2 nm respectively). The materials with poor nano-structured ordering were found to have low hydrogen cyanide capacities, between 11 and 19 mg g(-1), most likely owing to limited accessibility of the functional groups. (C) 2004 Elsevier Inc. All rights reserved.

A method of synthesis of silicious inorganic ordered materials (MCM-41-SBA-1) employing polyacrylic acid-C(n)TAB-TEOS nanoassemblies

In this work we describe the synthesis of a variety of MCM-41 type hexagonal and SBA-1 type cubic mesostructures and mesoporous silicious materials employing a novel synthesis concept based on polyacrylic acid (Pac)-C(n)TAB complexes as backbones of the developing structures. The ordered porosity of the solids was established by XRD and TEM techniques. The synthesis concept makes use of Pac-C(n)TAB nanoassemblies as a preformed scaffold, formed by the gradual increase of pH. On this starting matrix the inorganic precursor species SiO2 precipitate via hydrolysis of TEOS under the influence of increasing pH. The molecular weight (MW) of Pac, as well as the length of carbon chain in C,TAB, determine the physical and structural characteristics of the obtained materials. Longer chain surfactants (C(16)TAB) lead to the formation of hexagonal phase, while shorter chain surfactants (C(14)TAB, C(12)TAB) favor the SBA-1 phase. Lower MW of Pac (approximate to2000) leads to better-organized structures compared to higher MW ( 450,000), which leads to worm-like mesostructures. Cell parameters and pore size increase with increasing polyelectrolyte and/or surfactant chain, while at the same time SEM photography reveals that the particle size decreases. Conductivity experiments provide some insight into the proposed self-assembling pathway. (C) 2003 Elsevier Inc. All rights reserved.

Investigation of cadmium alternatives in thin-film coatings - art. no. 62860C

The health risks associated with the inhalation or ingestion of cadmium are well documented([1,2]). During the past 18 years, EU legislation has steadily been introduced to restrict its use, leaving a requirement for the development of replacement materials. This paper looks at possible alternatives to various cadmium II-VI dielectric compounds used in the deposition of optical thin-films for various opto-electronic devices. Application areas of particular interest are for infrared multilayer interference filter fabrication and solar cell industries, where cadmium-based coatings currently find widespread use. The results of single and multilayer designs comprising CdTe, CdS, CdSe and PbTe deposited onto group IV and II-VI materials as interference filters for the mid-IR region are presented. Thin films of SnN, SnO2, SnS and SnSe are fabricated by plasma assisted CVD, reactive RF sputtering and thermal evaporation. Examination of these films using FTIR spectroscopy, SEM, EDX analysis and optical characterisation methods provide details of material dispersion, absorption, composition, refractive index, energy band gap and layer thicknesses. The optimisation of deposition parameters in order to synthesise coatings with similar optical and semiconductor properties as those containing cadmium has been investigated. Results of environmental, durability and stability trials are also presented.

Investigation of Sn-based alternatives to cadmium in thin film coatings

New Sn-based materials have been deposited and characterised in terms of their optical and mechanical properties and compared with existing cadmium-based thin films that currently find wide spread use in the optoelectronic and semiconductor industries.

An ultra-wide passband (5-30µm) filter for FTIR studies of Photosystem II

This paper reports on the design and manufacture of an ultra-wide (5-30µm) infrared edge filter for use in FTIR studies of the low frequency vibrational modes of metallo-proteins. We present details of the spectral design and manufacture of such a filter which meets the demanding bandwidth and transparency requirements of the application, and spectra that present the new data possible with such a filter. A design model of the filter and the materials used in its construction has been developed capable of accurately predicting spectral performance at both 300K and at the reduced operating temperature at 200K. This design model is based on the optical and semiconductor properties of a multilayer filter containing PbTe (IV-VI) layer material in combination with the dielectric dispersion of ZnSe (II-VI) deposited on a CdTe (II-VI) substrate together with the use of BaF2 (II-VII) as an antireflection layer. Comparisons between the computed spectral performance of the model and spectral measurements from manufactured coatings over a wavelength range of 4-30µm and temperature range 300-200K are presented. Finally we present the results of the FTIR measurements of Photosystem II showing the improvement in signal to noise ratio of the measurement due to using the filter, together with a light induced FTIR difference spectrum of Photosystem II.

Optical and semi-conductor properties of Lead Telluride coatings

The optical and semiconductor properties of lead telluride coatings are dependant on various factors contributing to its performance. In this paper, we will present the temperature dependant effects of single layer lead telluride coatings on the dispersion and absorption characteristics, absorption edge, and carrier concentration from 15 K to 436 K using both experimental and theoretical analysis.

Ethnographic methodologies for construction research: knowing, practice and interventions

Ethnographic methodologies developed in social anthropology and sociology hold considerable promise for addressing practical, problem-based research concerned with the construction site. The extended researcher-engagement characteristic of ethnography reveals rich insights, yet is infrequently used to understand how workplace realities are lived out on construction sites. Moreover, studies that do employ these methods are rarely reported within construction research journals. This paper argues that recent innovations in ethnographic methodologies offer new routes to: posing questions; understanding workplace socialities (i.e. the qualities of the social relationships that develop on construction sites); learning about forms, uses and communication of knowledge on construction sites; and turning these into meaningful recommendations. This argument is supported by examples from an interdisciplinary ethnography concerning migrant workers and communications on UK construction sites. The presented research seeks to understand how construction workers communicate with managers and each other and how they stay safe on site, with the objective of informing site health-and-safety strategies and the production and evaluation of training and other materials.