Vibrational intensities VIII: CH3- and CD3- chloride, bromide and iodide

Absolute intensity measurements have been made on the fundamental vibrations of methyl chloride, bromide, and iodide, and their fully deuterated derivatives, by integrating the optical density over the absorption bands. The bands were fully pressure broadened by using up to 80 atmos of foreign gas. Band separations were made graphically. The results are analyzed in terms of the dipole moment derivatives with respect to symmetry coordinates in the molecule, (∂p/∂Si). The data on the different isotopic species are shown to yield consistent results, and this requirement of consistency has also been used as an aid in the analysis. In the E‐class vibrations the signs of the dipole moment derivatives have been determined unambiguously by assuming the permanent dipole to be directed CH3+☒X—.

Coordination behavior of pyridylmethylthioether system with cupric chloride and cupric bromide: CS bond cleavage and crystal structures

The coordination behavior of pyridylmethylthioether type of organic moieties having N2S2 donor set [L-1=1,2-bis(2-pyridylmethylthio)ethane, L-2 = 1,3-bis(2-pyridylmethyl-thio)propane and L-3 = 1,4-bis(2-pyridylmethylthio)butane] with copper(II) chloride and copper(II) bromide have been studied in different chemical environments. Copper(II) chloride assisted C-S bond cleavage of the organic moieties leading to the formation of copper(II) picolinate derivatives, whereas, under similar experimental conditions, no C-S bond cleavage was observed in the reaction with copper(II) bromide. The resulted copper(II) complexes isolated from the different mediums have been characterized by spectroscopic and X-ray crystallographic tools.

Reactive Halogens in the Marine Boundary Layer (RHaMBLe): the tropical North Atlantic experiments

The NERC UK SOLAS-funded Reactive Halogens in the Marine Boundary Layer (RHaMBLe) programme comprised three field experiments. This manuscript presents an overview of the measurements made within the two simultaneous remote experiments conducted in the tropical North Atlantic in May and June 2007. Measurements were made from two mobile and one ground-based platforms. The heavily instrumented cruise D319 on the RRS Discovery from Lisbon, Portugal to São Vicente, Cape Verde and back to Falmouth, UK was used to characterise the spatial distribution of boundary layer components likely to play a role in reactive halogen chemistry. Measurements onboard the ARSF Dornier aircraft were used to allow the observations to be interpreted in the context of their vertical distribution and to confirm the interpretation of atmospheric structure in the vicinity of the Cape Verde islands. Long-term ground-based measurements at the Cape Verde Atmospheric Observatory (CVAO) on São Vicente were supplemented by long-term measurements of reactive halogen species and characterisation of additional trace gas and aerosol species during the intensive experimental period. This paper presents a summary of the measurements made within the RHaMBLe remote experiments and discusses them in their meteorological and chemical context as determined from these three platforms and from additional meteorological analyses. Air always arrived at the CVAO from the North East with a range of air mass origins (European, Atlantic and North American continental). Trace gases were present at stable and fairly low concentrations with the exception of a slight increase in some anthropogenic components in air of North American origin, though NOx mixing ratios during this period remained below 20 pptv. Consistency with these air mass classifications is observed in the time series of soluble gas and aerosol composition measurements, with additional identification of periods of slightly elevated dust concentrations consistent with the trajectories passing over the African continent. The CVAO is shown to be broadly representative of the wider North Atlantic marine boundary layer; measurements of NO, O3 and black carbon from the ship are consistent with a clean Northern Hemisphere marine background. Aerosol composition measurements do not indicate elevated organic material associated with clean marine air. Closer to the African coast, black carbon and NO levels start to increase, indicating greater anthropogenic influence. Lower ozone in this region is possibly associated with the increased levels of measured halocarbons, associated with the nutrient rich waters of the Mauritanian upwelling. Bromide and chloride deficits in coarse mode aerosol at both the CVAO and on D319 and the continuous abundance of inorganic gaseous halogen species at CVAO indicate significant reactive cycling of halogens. Aircraft measurements of O3 and CO show that surface measurements are representative of the entire boundary layer in the vicinity both in diurnal variability and absolute levels. Above the inversion layer similar diurnal behaviour in O3 and CO is observed at lower mixing ratios in the air that had originated from south of Cape Verde, possibly from within the ITCZ. ECMWF calculations on two days indicate very different boundary layer depths and aircraft flights over the ship replicate this, giving confidence in the calculated boundary layer depth.

The effect of aqueous diffusion on the fractionation of chlorine and bromine stable isotopes

Diffusive isotopic fractionation factors are important in order to understand natural processes and have practical application in radioactive waste storage and carbon dioxide sequestration. We determined the isotope fractionation factors and the effective diffusion coefficients of chloride and bromide ions during aqueous diffusion in polyacrylamide gel. Diffusion was determined as functions of temperature, time and concentration. The effect of temperature is relatively large on the diffusion coefficient (D) but only small on isotope fractionation. For chlorine, the ratio, D-35cl/D-37cl varied from 1.00128 +/- 0.00017 (1 sigma) at 2 degrees C to 1.00192 +/- 0.00015 at 80 degrees C. For bromine, D-79Br/D-81Br varied from 1.00098 +/- 0.00009 at 2 degrees C to 1.0064 +/- 0.00013 at 21 degrees C and 1.00078 +/- 0.00018 (1 sigma) at 80 degrees C. There were no significant effects on the isotope fractionation due to concentration. The lack of sensitivity of the diffusive isotope fractionation to anything at the most common temperatures (0 to 30 C) makes it particularly valuable for application to understanding processes in geological environments and an important natural tracer in order to understand fluid transport processes. (C) 2009 Elsevier Ltd. All rights reserved.

A comparison of the role of two blue-green algae in THM and HAA formation

The contribution of two blue-green algae species, Anabaeria flos-aquae and Microcystis aeruginosa, to the formation of trihalomethanes (THMs) and haloacetic acids (HAAs) was investigated. The experiments examined the formation potential of these disinfection by-products (DBPs) from both algae cells and extracellular organic matter (EOM) during four algal growth phases. Algal cells and EOM of Anabaena and Microcystis exhibited a high potential for DBP formation. Yields of total THMs (TTHM) and total HAAs (THAA) were closely related to the growth phase. Reactivity of EOM from Anabaena was slightly higher than corresponding cells, while the opposite result was found for Microcystis. Specific DBP yields (yield/unit C) of Anabaena were in the range of 2-11 mu mol/mmol C for TTHM and 217 mu mol/mmol C for THAA, while those of Microcystis were slightly higher. With regard to the distributions of individual THM and HAA compounds, differences were observed between the algae species and also between cells and EOM. The presence of bromide shifted the dominant compounds from HAAs to THMs. (C) 2009 Elsevier Ltd. All rights reserved.

Antifungal activity of bacterium symbiotically associated with Steinernema abbasi towards Fusarium oxysporum

Fusarium oxysporum f.sp. lycopersici (Fol) is the causal agent of the Fusarium wilt disease of tomato. Soil fumigant (mainly methyl bromide) applications are in use for its control. With the increasing environmental awareness, biological control methods are under investigation for their effectiveness, including the use of antagonists. Pseudomonas oryzihabitans (=Flavimonas oryzihabitans), a symbiont of the entomopathogenic nematode Steinernema abbasi was investigated as an antagonism of a Fol isolate in two laboratory and two glasshouse experiments. Bacteria and cell-free filtrate antifungal activity were tested both in dual cultures and in broth culture. In pot experiments, suspensions of bacteria in five concentrations (106, 105, 104, 103 and 102 cells/ml) were tested for their ability to control the pathogen at 25±3°C. In all tests the bacterium significantly inhibited the growth of Fol mycelium in vitro. Similar results were obtained when the bacterium was also tested against Fusarium oxysporum f.sp. radicis lycopersici and against Rhizoctonia solani. Moreover, when it was introduced into the soil, it was able to suppress the Fusarium wilt of tomato.

Development of a PCR-based assay for rapid and reliable identification of pathogenic Fusaria

Identification of Fusarium species has always been difficult due to confusing phenotypic classification systems. We have developed a fluorescent-based polymerase chain reaction assay that allows for rapid and reliable identification of five toxigenic and pathogenic Fusarium species. The species includes Fusarium avenaceum, F. culmorum, F. equiseti, F. oxysporum and F. sambucinum. The method is based on the PCR amplification of species-specific DNA fragments using fluorescent oligonucleotide primers, which were designed based on sequence divergence within the internal transcribed spacer region of nuclear ribosomal DNA. Besides providing an accurate, reliable, and quick diagnosis of these Fusaria, another advantage with this method is that it reduces the potential for exposure to carcinogenic chemicals as it substitutes the use of fluorescent dyes in place of ethidium, bromide. Apart from its multidisciplinary importance and usefulness, it also obviates the need for gel electrophoresis. (C) 2002 Published by Elsevier Science B.V. on behalf of the Federation of European Microbiological Societies.

Evaluation of the binding ability of a novel dioxatetraazamacrocyclic receptor that contains two phenanthroline units: selective uptake of carboxylate anions

The novel dioxatetraaza macrocycle [26]phen(2)N(4)O(2), which incorporates two phenanthroline units, has been synthesized, and its acid-base behavior has been evaluated by potentiometric and H-1 NMR methods. Six protonation constants were determined, and the protonation sequence was established by NMR. The location of the fifth proton on the phen nitrogen was confirmed by X-ray determinations of the crystal structures of the receptor as bromide and chloride salts. The two compounds have the general molecular formula {(H-5[26]phen(2)N(4)O(2))X-n(H2O)(5-n)}X(n-1)(.)mH(2)O, where X = Cl, n = 3, and m = 6 or X = Br, n = 4, and m = 5.5. In the solid state, the (H-5[26]phen(2)N(4)O(2))(5+) cation adopts a "horseshoe" topology with sufficient room to encapsulate three or four halogen anions through the several N-(HX)-X-... hydrogen-bonding interactions. Two supermolecules {(H-5[26]phen(2)N(4)O(2))X-n(H2O)(5-n)}((5-n)+) form an interpenetrating dimeric species, which was also found by ESI mass spectrum. Binding studies of the protonated macrocycle with aliphatic (ox(2-), mal(2-), suc(2-), cit(3-), cta(3-)) and aromatic (bzc(-), naphc(-), anthc(-), pyrc(-), ph(2-), iph(2-), tph(2-), btc(3-)) anions were determined in water by potentiometric methods. These studies were complemented by H-1 NMR titrations in D2O of the receptor with selected anions. The H-i[26]phen(2)N(4)O(2)(i+) receptor can selectively uptake highly charged or extended aromatic carboxylate anions, such as btc(3-) and pyrc(-), in the pH ranges of 4.0-8.5 and < 4.0, respectively, from aqueous solution that contain the remaining anions as pollutants or contaminants. To obtain further insight into these structural and experimental findings, molecular dynamics (MD) simulations were carried out in water solution.

Thermoselective phase property of silica tethered with fluorinated chains for controlled 'release' and 'capture' of catalytic fluorous tin species

The temperature dependent mixing of organic and fluorous phases is one of the key principals of fluorous biphasic systems (FBS). Given the high cost of the perfluorous solvents and their impacts to the environment, it is apparent that elimination of these solvents in bulk quantity in the FBS is advantageous. We report for the first time, the surface coverage of silica with a fluorous solvent like material that traps (at ambient temperatures) and releases (at elevated temperatures) a fluorous tin bromide in organic solvent. Here, we demonstrate the catalytic utilisation of this species for the hydrocyclisation of 6-bromo-1-hexene with NaBH4. (C) 2002 Elsevier Science B.V. All rights reserved.

Synthesis of multicarboxylic acid appended imidazolium ionic liquids and their application in palladium-catalyzed selective oxidation of styrene

A series of multicarboxylic acid appended imidazolium ionic liquids ( McaILs) with chloride [ Cl](-) or bromide [ Br](-) as anions have been synthesized and characterized. Deprotonation of these ionic acids gives the corresponding zwitterions. Re-protonation of the zwitterions with strong Bronsted acids gives a series of new ionic acid-adducts, many of which remained as room-temperature ionic liquids. A new catalytic system, McaIL/PdCl2 for the selective catalytic oxidation of styrene to acetophenone with hydrogen peroxide as an oxidant has been attempted. In the presence of McaILs, it is found that the quantity of palladium chloride PdCl2 used can be greatly reduced while the activity ( TOF) and selectivity towards acetophenone are enhanced sharply. It is also shown that the catalytic properties of this system could be finely tuned through the molecular design of the McaILs. The best TOF value obtained so far is 146 h(-1) with 100% conversion of styrene at 93% selectivity to acetophenone. In addition, the catalytic activity has been maintained for at least ten catalytic cycles.

A new route to furanoeremophilane sesquiterpenoids. Synthesis of Senecio metabolites (+/-)-6-hydroxyeuryopsin, (+/-)-1,10-epoxy-6-hydroxyeuryopsin, (+/-)-toluccanolide A and (+/-)-toluccanolide C

A new strategy for the synthesis of sesquiterpenoids of the furanoeremophilane family was developed in which the tricyclic nucleus was assembled in an A + C -> A - C -> A - B - C sequence. The A - C connection was made via coupling of a cyclohexenylmethyl bromide with a stannylfuran under "ligandless" Stille conditions, and the key cyclization which closed ring B was accomplished with complete stereocontrol by intramolecular formylation of a 2-silylfuran in the presence of trimethylsilyl triflate. This route was used to complete the first total syntheses of the furanoeremophilane 6-hydroxyeuryopsin and the eremophilenolides toluccanolide A and toluccanolide C, as well as a formal synthesis of 1,10-epoxy-6-hydroxyeuryopsin.

Micellar catalysis for partial oxidation of toluene to benzoic acid in supercritical CO2: effects of fluorinated surfactants

One of the key hindrances on development of solid catalysts containing cobalt species for partial oxidation of organic molecules at mild conditions in conventional liquid phase is the severe metal leaching. The leached soluble Co species with a higher degree of freedom always out-performs those of solid supported Co species in oxidation catalysis. However, the homogeneous Co species concomitantly introduces separation problems. We have recently reponed for the first time, a new oxidation catalyst system for the oxidation of organic molecules in supercritical CO2 using the principle of micellar catalysis. [CF3(CF2)(8)COO](2)Co.xH(2)O (the fluorinated anionic moiety forms aqueous reverse micelles carrying water-soluble Co2+ cations in scCO(2)) was previously shown to be extremely active for the oxidation of toluene in the presence of sodium bromide in water-CO2 mixture, giving 98% conversion and 99% selectivity to benzoic acid at 120 degreesC. In this study, we show that the effects of varying the type of surfactant counterions and the length of the surfactant chains on catalysis. It is found that the use of [CF3(CF2)(8)COO](2)Mg.yH(2)O/Co(II) acetate is as effective as the [CF3(CF2)(8)COO](2)Co.xH(2)O and the fluorinated chain length used has a subtle effect on the catalytic rate measured. It is also demonstrated that this new type of micellar catalyst in scCO(2) can be easily separated via CO2 depressurisation and be reused without noticeable deactivation. (C) 2003 Elsevier B.V. All rights reserved.

Recovery of gallic acid with colloidal gas aphrons (CGA)

In the present paper the potential application of colloidal gas aphrons (CGA) to the recovery of antioxidants from wine-making waste extracts is investigated. CGA were generated by stirring a buffered solution (400 ml) of a cationic surfactant(cetyltrimethylammonium bromide, CTAB) at 8000 rpm for 10 minutes. Trials were carried out on standard solutions (2 ml) of gallic acid (GA) 200 mg/l with varying volumes of colloidal gas aphrons (20-60 ml) generated with varying concentrations of CTAB (2 and 4 mM). Influence of pH, solvent (buffered aqueous solution and ethanol), CTAB to GA molar ratio on recovery were studied. Best recovery (63%) was achieved from an aqueous solution of GA and at a CTAB to GA molar ratio of 16. Separation is mainly driven by electrostatic interactions but pH conditions are to be optimised to preserve the GA antioxidant power.

An insight into the mechanism of protein separation by colloidal gas aphrons (CGA) generated from ionic surfactants

Colloidal gas aphrons (CGA), which are surfactant stabilised microbubbles, have been previously applied for the recovery of proteins from model mixtures and a few studies have demonstrated the potential of these dispersions for the selective recovery of proteins from complex mixtures. However there is a lack of understanding of the mechanism of separation and forces governing the selectivity of the separation. In this paper a mechanistic study is carried out to determine the main factors and forces influencing the selectivity of separation of whey proteins with CGA generated from ionic surfactants. Two different separation strategies were followed: (i) separation of lactoferrin and lactoperoxidase by anionic CGA generated from a solution of sodium bis-(2-ethyl hexyl) sulfosuccinate (AOT); (ii) separation of beta-lactoglobulin by cationic CGA generated from a solution of cetyltrimethylammonium bromide (CTAB). Separation results indicate that electrostatic interactions are the main forces determining the selectivity however these could not completely explain the selectivities obtained following both strategies. Protein-surfactant interactions were studied by measuring the zeta potential changes on individual proteins upon addition of surfactant and at varying pH. Interestingly strongest electrostatic interactions were measured at those pH and surfactant to protein mass ratios which were optimum for protein separation. Effect of surfactant on protein conformation was determined by measuring the change in fluorescence intensity upon addition of surfactant at varying pH. Differences in the fluorescence patterns were detected among proteins which were correlated to differences in their conformational features which could in turn explain their different separation behaviour. The effect of conformation on selectivity was further proven by experiments in which conformational changes were induced by pre-treatment of whey (heating) and by storage at 4 degrees C. Overall it can be concluded that separation of proteins by ionic CGA is driven mainly by electrostatic interactions however conformational features will finally determine the selectivity of the separation with competitive adsorption having also an effect. (c) 2006 Elsevier B.V. All rights reserved.

Selective separation of beta-lactoglobulin from sweet whey using CGAs generated from the cationic surfactant CTAB

The selective separation of whey proteins was studied using colloidal gas aphrons generated from the cationic surfactant cetyl trimethyl ammonium bromide (CTAB). From the titration curves obtained by zeta potential measurements of individual whey proteins, it was expected to selectively adsorb the major whey proteins, i.e., bovine serum albumin, alpha-lactalbumin, and beta-lactoglobulin to the aphrons and elute the remaining proteins (lactoferrin and lactoperoxidase) in the liquid phase. A number of process parameters including pH, ionic strength, and mass ratio of surfactant to protein (M-CTAB/M-TP) were varied in order to evaluate their effect on protein separation. Under optimum conditions (2 mmol/l CTAB, M-CTAB/M-TP = 0.26-0.35, pH 8, and ionic strength = 0.018 mol/l), 80-90% beta-lactoglobulin was removed from the liquid phase as a precipitate, while about 75% lactoferrin and lactoperoxidase, 80% bovine serum albumin, 95% immunoglobulin, and 65% alpha-lactalbumin were recovered in the liquid fraction. Mechanistic studies using zeta potential measurements and fluorescence spectroscopy proved that electrostatic interactions modulate only partially the selectivity of protein separation, as proteins with similar surface charges do not separate to the same extent between the two phases. The selectivity of recovery of beta-lactoglobulin probably occurs in two steps: the first being the selective interaction of the protein with opposite-charged surfactant molecules by means of electrostatic interactions, which leads to denaturation of the protein and subsequent formation and precipitation of the CTAB-beta-lactoglobulin complex. This is followed by the separation of CTAB-beta-lactoglobulin aggregates from the bulk liquid by flotation in the aphron phase. In this way, CGAs act as carriers which facilitate the removal of protein precipitate. (c) 2005 Wiley Periodicals, Inc.