A preliminary investigation of the release of oil from contaminated clays and other fine-grained sediments during consolidation

Fine-grained sediments on land, or in a freshwater or marine environment, may become contaminated with a wide range of pollutants including hydrocarbons. This paper is concerned with preliminary studies of the mobilization and transportation of hydrocarbons, during the process of consolidation, to adjacent sediments or water bodies. A modified Rowe Cell was used to measure the consolidation properties of prepared kaolinite and bentonite clay-water slurries, with and without the addition of oil, along with hydrocarbon-bearing drill-cuttings samples taken from the sea-bed adjacent to two North Sea oil-well platforms. The consolidation properties of the kaolinite and bentonite clay slurries were little altered by the addition of oil, which was present at concentrations of between 8073 and 59 572 mg kg(-1). During each consolidation stage, samples of the expelled pore-fluids were collected and analysed for oil content. These values were very low in comparison with the original oil concentration in the samples and changed little between each consolidation stage. Analysis of the slurry samples both before and after consolidation confirms that, proportionally, little oil is removed as a result of consolidation. The implication of these results is that, for the range of samples tested, the very high hydraulic gradients and particle rearrangements that occur during the process of consolidation are capable of releasing only proportionally small amounts of oil bound to the fine-grained clay and silt particles.

A preliminary investigation of the release of oil from contaminated clays and other fine-grained sediments during consolidation

Fine-grained sediments on land, or in a freshwater or marine environment, may become contaminated with a wide range of pollutants including hydrocarbons. This paper is concerned with preliminary studies of the mobilization and transportation of hydrocarbons, during the process of consolidation, to adjacent sediments or water bodies. A modified Rowe Cell was used to measure the consolidation properties of prepared kaolinite and bentonite clay-water slurries, with and without the addition of oil, along with hydrocarbon-bearing drill-cuttings samples taken from the sea-bed adjacent to two North Sea oil-well platforms. The consolidation properties of the kaolinite and bentonite clay slurries were little altered by the addition of oil, which was present at concentrations of between 8073 and 59 572 mg kg(-1). During each consolidation stage, samples of the expelled pore-fluids were collected and analysed for oil content. These values were very low in comparison with the original oil concentration in the samples and changed little between each consolidation stage. Analysis of the slurry samples both before and after consolidation confirms that, proportionally, little oil is removed as a result of consolidation. The implication of these results is that, for the range of samples tested, the very high hydraulic gradients and particle rearrangements that occur during the process of consolidation are capable of releasing only proportionally small amounts of oil bound to the fine-grained clay and silt particles.

Fine-grained multi-phase array designs

Hybrid multiprocessor architectures which combine re-configurable computing and multiprocessors on a chip are being proposed to transcend the performance of standard multi-core parallel systems. Both fine-grained and coarse-grained parallel algorithm implementations are feasible in such hybrid frameworks. A compositional strategy for designing fine-grained multi-phase regular processor arrays to target hybrid architectures is presented in this paper. The method is based on deriving component designs using classical regular array techniques and composing the components into a unified global design. Effective designs with phase-changes and data routing at run-time are characteristics of these designs. In order to describe the data transfer between phases, the concept of communication domain is introduced so that the producer–consumer relationship arising from multi-phase computation can be treated in a unified way as a data routing phase. This technique is applied to derive new designs of multi-phase regular arrays with different dataflow between phases of computation.

Annual textural banding in Holocene estuarine silts, Severn Estuary Levels (SW Britain): patterns, cause and implications

A high-resolution textural study has been made of laminated and banded estuarine silts exposed intertidally at representative localities and horizons in the Holocene deposits of the Severn Estuary Levels. The laminae, on a submillimetre to millimetre scale, are sharp-based, graded couplets formed of a lower silty part overlain by a finer-textured clayey element. The centimetre- to decimetre-scale banding is formed of laminae in alternating, gradually intergrading sets of relatively coarse and relative fine-grained examples. At outcrop in the field, the banding is recognizable because the coarse sets prove to be recessive to varying degrees under the influence of weathering and current action. Independent evidence at two localities points toward an annual origin for the banding; at a third it arose during part of what appears to have been a relatively short period. Quantified physical arguments suggest that the textural banding is a response of suspended fine sediment to marked seasonal changes in sea temperature and windiness. The banded silts occur in four distinct stratigraphical contexts and record high deposition rates (order 0.01-0.1 m/yr). Because physical factors determine their textures, the silts potentially afford insights in all contexts into aspects of changing Holocene climatic conditions. In one context, the thickness of the bands points to high (order 0.01-0.1 m/yr) but comparatively short-lived (order 10s-100s yrs) rates of relative water-level rise. In the others, however, the banding has no implications for sea-level behaviour, and simply records gross environmental disequilibrium, for example, the recovery of mudflats/marshes after an erosional episode. Similarly, because on account of their rapid accumulation the banded silts preserve animal and human tracks and trackways especially well, they provide an archive of animal and human behaviour in the area during the Holocene.

Seasonality of modern pollen and sediment deposition in an estuarine context: the Severn Estuary Levels, southwest England

Recent sedimentological and palynological research on subfossil Holocene banded sediments from the Severn Estuary Levels suggested seasonality of deposition, registered by variations in mineral grain-size and pollen assemblages between different parts of the bands. Here we provide data that strengthen this interpretation from sampling of modern sediments and pollen deposition on an active mudflat and saltmarsh on the margin of the Severn Estuary, and comparison with a vegetation survey and contemporary records of climate, river and tidal regimes. The results of grain-size analysis indicate deposition of comparatively coarse-grained silts during the relatively cool and windy conditions of winter and comparatively fine-grained sediments during relatively warm and calm summer months. Pollen analysis demonstrates the significance of long-term storage of pollen grains and fern spores in the estuarine waterbody, superimposed on which seasonal variations in pollen inputs from local and regional vegetation remain detectable. Copyright (C) 2007 John Wiley & Sons, Ltd.

Seasonality of delta C-13 and C/N ratios in modern and mid-holocene sediments in the Severn Estuary levels, SW Britain

Bulk organic VC and C/N ratios from mid-Holocene salt-marsh deposits with sedimentary banding reveal subtle but significant differences between coarse- and fine-grained deposits. These are consistent with findings from seasonally sampled modern silts, and with the interpretation, on physical and palynological grounds, of the fine-grained and coarse-grained components as warm-season and cold-season deposits, respectively. The control is considered to be seasonal variations in the character of the organic matter supplied.

Seasonal deposition of Holocene banded sediments in the Severn Estuary Levels (southwest Britain): palynological and sedimentological evidence

Banded sediments outcrop widely in the intertidal zone of the Severn Estuary and have been suggested, on the basis of textural analysis, to have formed in response to seasonal variations in sea temperature and windiness (Holocene, 14 (2004) 536). Here palynological and sedimentological analyses of banded sediments of mid-Holocene date from Gold Cliff, on the Welsh side of the Severn Estuary, are combined to test and further develop the hypothesis of seasonal deposition. Pollen percentage and concentration data are presented from a short sequence of bands to establish whether textural variations in the bands coincide with variations in pollen content reflecting seasonal flowering patterns. It is shown that fine-grained band parts contain higher total pollen concentrations, and a higher proportion of pollen from late spring- to summer-flowering plants, than coarse-grained band parts. Pollen in the coarser deposits appears primarily to reflect deposition from the buffering `reservoir' of suspended pollen in the estuarine water-body and from rivers, when there is little pollen in the air in winter, while the finer sediments contain pollen deposited from the atmosphere during the flowering season, superimposed on these `background' sources. The potential of such deposits for refining chronologies and identifying seasonality of coastal processes is noted, and the results of charcoal particle analysis of the bands presented as an example of how they have the potential to shed light on seasonal and annual patterns of human activity. (C) 2004 Elsevier Ltd. All rights reserved.

The Dubawnt Lake palaeo-ice stream: evidence for dynamic ics sheet behaviour on the Canadian Shield and insights regarding the controls on ice-stream location and vigour

We report evidence for a major ice stream that operated over the northwestern Canadian Shield in the Keewatin Sector of the Laurentide Ice Sheet during the last deglaciation 9000-8200 (uncalibrated) yr BP. It is reconstructed at 450 km in length, 140 km in width, and had an estimated catchment area of 190000 km. Mapping from satellite imagery reveals a suite of bedforms ('flow-set') characterized by a highly convergent onset zone, abrupt lateral margins, and where flow was presumed to have been fastest, a remarkably coherent pattern of mega-scale glacial lineations with lengths approaching 13 km and elongation ratios in excess of 40:1. Spatial variations in bedform elongation within the flow-set match the expected velocity field of a terrestrial ice stream. The flow pattern does not appear to be steered by topography and its location on the hard bedrock of the Canadian Shield is surprising. A soft sedimentary basin may have influenced ice-stream activity by lubricating the bed over the downstream crystalline bedrock, but it is unlikely that it operated over a pervasively deforming till layer. The location of the ice stream challenges the view that they only arise in deep bedrock troughs or over thick deposits of 'soft' fine-grained sediments. We speculate that fast ice flow may have been triggered when a steep ice sheet surface gradient with high driving stresses contacted a proglacial lake. An increase in velocity through calving could have propagated fast ice flow upstream (in the vicinity of the Keewatin Ice Divide) through a series of thermomechanical feedback mechanisms. It exerted a considerable impact on the Laurentide Ice Sheet, forcing the demise of one of the last major ice centres.

Hierarchical composite regular parallel architecture

The design space of emerging heterogenous multi-core architectures with re-configurability element makes it feasible to design mixed fine-grained and coarse-grained parallel architectures. This paper presents a hierarchical composite array design which extends the curret design space of regular array design by combining a sequence of transformations. This technique is applied to derive a new design of a pipelined parallel regular array with different dataflow between phases of computation.

Validation of the FALL3D ash dispersion model using observations of the 2010 Eyjafjallajökull volcanic ash clouds

During April-May 2010 volcanic ash clouds from the Icelandic Eyjafjallajökull volcano reached Europe causing an unprecedented disruption of the EUR/NAT region airspace. Civil aviation authorities banned all flight operations because of the threat posed by volcanic ash to modern turbine aircraft. New quantitative airborne ash mass concentration thresholds, still under discussion, were adopted for discerning regions contaminated by ash. This has implications for ash dispersal models routinely used to forecast the evolution of ash clouds. In this new context, quantitative model validation and assessment of the accuracies of current state-of-the-art models is of paramount importance. The passage of volcanic ash clouds over central Europe, a territory hosting a dense network of meteorological and air quality observatories, generated a quantity of observations unusual for volcanic clouds. From the ground, the cloud was observed by aerosol lidars, lidar ceilometers, sun photometers, other remote-sensing instru- ments and in-situ collectors. From the air, sondes and multiple aircraft measurements also took extremely valuable in-situ and remote-sensing measurements. These measurements constitute an excellent database for model validation. Here we validate the FALL3D ash dispersal model by comparing model results with ground and airplane-based measurements obtained during the initial 14e23 April 2010 Eyjafjallajökull explosive phase. We run the model at high spatial resolution using as input hourly- averaged observed heights of the eruption column and the total grain size distribution reconstructed from field observations. Model results are then compared against remote ground-based and in-situ aircraft-based measurements, including lidar ceilometers from the German Meteorological Service, aerosol lidars and sun photometers from EARLINET and AERONET networks, and flight missions of the German DLR Falcon aircraft. We find good quantitative agreement, with an error similar to the spread in the observations (however depending on the method used to estimate mass eruption rate) for both airborne and ground mass concentration. Such verification results help us understand and constrain the accuracy and reliability of ash transport models and it is of enormous relevance for designing future operational mitigation strategies at Volcanic Ash Advisory Centers.

Cortical activation during executed, imagined, observed, and passive wrist movements in healthy volunteers and stroke patients

Motor imagery, passive movement, and movement observation have been suggested to activate the sensorimotor system without overt movement. The present study investigated these three covert movement modes together with overt movement in a within-subject design to allow for a fine-grained comparison of their abilities in activating the sensorimotor system, i.e. premotor, primary motor, and somatosensory cortices. For this, 21 healthy volunteers underwent functional magnetic resonance imaging (fMRI). In addition we explored the abilities of the different covert movement modes in activating the sensorimotor system in a pilot study of 5 stroke patients suffering from chronic severe hemiparesis. Results demonstrated that while all covert movement modes activated sensorimotor areas, there were profound differences between modes and between healthy volunteers and patients. In healthy volunteers, the pattern of neural activation in overt execution was best resembled by passive movement, followed by motor imagery, and lastly by movement observation. In patients, attempted overt execution was best resembled by motor imagery, followed by passive movement, and lastly by movement observation. Our results indicate that for severely hemiparetic stroke patients motor imagery may be the preferred way to activate the sensorimotor system without overt behavior. In addition, the clear differences between the covert movement modes point to the need for within-subject comparisons.

Gradient competence at the syntax-discourse interface

In this article, we present additional support of Duffield's (2003, 2005) distinction between Underlying Competence and Surface Competence. Duffield argues that a more fine-grained distinction between levels of competence and performance is warranted and necessary. While underlying competence is categorical, surface competence is more probabilistic and gradient, being sensitive to lexical and constructional contingencies, including the contextual appropriateness of a given construction. We examine a subset of results from a study comparing native and learner competence of properties at the syntax-discourse interface. Specifically, we look at the acceptability of Clitic Right Dislocation in native and L2 Spanish, in discourse-appropriate context. We argue that Duffield's distinction is a possible explanation of our results.

Potential reduction of concrete deterioration through controlled DEF in hydrated concrete

Delayed ettringite formation (DEF) is a chemical reaction with proven damaging effects on hydrated concrete. Ettringite crystals can cause cracks and their widening due to pressure on cracked walls caused by the positive volume difference in the reaction. Concrete may show improvements in strength at early ages but further growth of cracks causes widening and spreading through the concrete structure. In this study, finely dispersed crystallization nuclei achieved by adding air-entraining agent (AEA) and short vibration of specimens is presented as the main prerequisite for reducing DEF-induced deterioration of hydrated concrete. The study presents the method and mechanism for obtaining the required nucleation. Controlling long-term DEF by providing AEA-induced crystallisation nuclei, prevented excessive and rapid initial strength improvements, and resulted in a slight increase of compressive strength of fine grained concrete with only marginally lower density.

Performance-based contracting in the construction sector

Construction procurement is complex and there is a very wide range of options available to procurers. Inappropriate choices about how to procure may limit practical opportunities for innovation. In particular, traditional approaches to construction procurement set up many obstacles for technology suppliers to provide innovative solutions. This is because they are often employed as sub-contractors simply to provide and install equipment to specifications developed before the point at which they become involved in a project. A research team at the University of Reading has developed a procurement framework that comprehensively defines the various options open to procurers in a more fine-grained way than has been known in the past. This enables informed decisions that can establish tailor-made procurement approaches that take into account the needs of specific clients. It enables risk and reward structures to be aligned so that contracts and payment mechanisms are aligned precisely with what a client seeks to achieve. This is not a “one-size-fits-all” approach. Rather, it is an approach that enables informed decisions about how to organize individual procurements that are appropriate to particular circumstances, acknowledging that they differ for each client and for each procurement exercise. Within this context, performance-based contracting (PBC) is explored in terms of the different ways in which technology suppliers within constructed facilities might be encouraged and rewarded for the kinds of innovation sought by the ultimate clients. Examples from various industry sectors are presented, from public sector and from private sector, with a commentary about what they sought to achieve and the extent to which they were successful. The lessons from these examples are presented in terms of feasibility in relation to financial issues, governance, economics, strategic issues, contractual issues and cash flow issues for clients and for contractors. Further background documents and more detailed readings are provided in an appendix for those who wish to find out more.

Holocene alluvial environments at Barking, Lower Thames Valley (London, UK)

Deposit modelling based on archived borehole logs supplemented by a small number of dedicated boreholes is used to reconstruct the main boundary surfaces and the thickness of the main sediment units within the succession of Holocene alluvial deposits underlying the floodplain in the Barking Reach of the Lower Thames Valley. The basis of the modelling exercise is discussed and the models are used to assess the significance of floodplain relief in determining patterns of sedimentation. This evidence is combined with the results of biostratigraphical and geochronological investigations to reconstruct the environmental conditions associated with each successive stage of floodplain aggradation. The two main factors affecting the history and spatial pattern of Holocene sedimentation are shown to be the regional behaviour of relative sea level and the pattern of relief on the surface of the sub-alluvial, Late Devensian Shepperton Gravel. As is generally the case in the Lower Thames Valley, three main stratigraphic units are recognised, the Lower Alluvium, a peat bed broadly equivalent to the Tilbury III peat of Devoy (1979) and an Upper Alluvium. There is no evidence to suggest that the floodplain was substantially re-shaped by erosion during the Holocene. Instead, the relief inherited from the Shepperton Gravel surface was gradually buried either by the accumulation of peat or by deposition of fine-grained sediment from suspension in standing or slow-moving water. The palaeoenvironmental record from Barking confirms important details of the Holocene record observed elsewhere in the Lower Thames Valley, including the presence of Taxus in the valley-floor fen carr woodland between about 5000 and 4000 cal BP, and the subsequent growth of Ulmus on the peat surface.