Observing crosswind over urban terrain using scintillometer and Doppler lidar

In this study, the crosswind (wind component perpendicular to a path, U⊥) is measured by a scintillometer and estimated with Doppler lidar above the urban environment of Helsinki, Finland, for 15 days. The scintillometer allows acquisition of a path-averaged value of U⊥ (U⊥), while the lidar allows acquisition of path-resolved U⊥ (U⊥ (x), where x is the position along the path). The goal of this study is to evaluate the performance of scintillometer U⊥ estimates for conditions under which U⊥ (x) is variable. Two methods are applied to estimate U⊥ from the scintillometer signal: the cumulative-spectrum method (relies on scintillation spectra) and the look-up-table method (relies on time-lagged correlation functions). The values of U⊥ of both methods compare well with the lidar estimates, with root-mean-square deviations of 0.71 and 0.73 m s−1. This indicates that, given the data treatment applied in this study, both measurement technologies are able to obtain estimates of U⊥ in the complex urban environment. The detailed investigation of four cases indicates that the cumulative-spectrum method is less susceptible to a variable U⊥ (x) than the look-up-table method. However, the look-up-table method can be adjusted to improve its capabilities for estimating U⊥ under conditions under for which U⊥ (x) is variable.

Donepezil for the symptomatic treatment of patients with mild to moderate Alzheimer's disease: a meta-analysis of individual patient data from randomised controlled trials

Background: The objective was to evaluate the efficacy and tolerability of donepezil (5 and 10 mg/day) compared with placebo in alleviating manifestations of mild to moderate Alzheimer's disease (AD). Method: A systematic review of individual patient data from Phase II and III double-blind, randomised, placebo-controlled studies of up to 24 weeks and completed by 20 December 1999. The main outcome measures were the ADAS-cog, the CIBIC-plus, and reports of adverse events. Results: A total of 2376 patients from ten trials were randomised to either donepezil 5 mg/day (n = 821), 10 mg/day (n = 662) or placebo (n = 893). Cognitive performance was better in patients receiving donepezil than in patients receiving placebo. At 12 weeks the differences in ADAS-cog scores were 5 mg/day-placebo: - 2.1 [95% confidence interval (CI), - 2.6 to - 1.6; p < 0.001], 10 mg/day-placebo: - 2.5 ( - 3.1 to - 2.0; p < 0.001). The corresponding results at 24 weeks were - 2.0 ( - 2.7 to - 1.3; p < 0.001) and - 3.1 ( - 3.9 to - 2.4; p < 0.001). The difference between the 5 and 10 mg/day doses was significant at 24 weeks (p = 0.005). The odds ratios (OR) of improvement on the CIBIC-plus at 12 weeks were: 5 mg/day-placebo 1.8 (1.5 to 2.1; p < 0.001), 10 mg/day-placebo 1.9 (1.5 to 2.4; p < 0.001). The corresponding values at 24 weeks were 1.9 (1.5 to 2.4; p = 0.001) and 2.1 (1.6 to 2.8; p < 0.001). Donepezil was well tolerated; adverse events were cholinergic in nature and generally of mild severity and brief in duration. Conclusion: Donepezil (5 and 10 mg/day) provides meaningful benefits in alleviating deficits in cognitive and clinician-rated global function in AD patients relative to placebo. Increased improvements in cognition were indicated for the higher dose. Copyright © 2004 John Wiley & Sons, Ltd.

Data-driven treatment selection for seamless phase II/III trials incorporating early-outcome data

Seamless phase II/III clinical trials are conducted in two stages with treatment selection at the first stage. In the first stage, patients are randomized to a control or one of k > 1 experimental treatments. At the end of this stage, interim data are analysed, and a decision is made concerning which experimental treatment should continue to the second stage. If the primary endpoint is observable only after some period of follow-up, at the interim analysis data may be available on some early outcome on a larger number of patients than those for whom the primary endpoint is available. These early endpoint data can thus be used for treatment selection. For two previously proposed approaches, the power has been shown to be greater for one or other method depending on the true treatment effects and correlations. We propose a new approach that builds on the previously proposed approaches and uses data available at the interim analysis to estimate these parameters and then, on the basis of these estimates, chooses the treatment selection method with the highest probability of correctly selecting the most effective treatment. This method is shown to perform well compared with the two previously described methods for a wide range of true parameter values. In most cases, the performance of the new method is either similar to or, in some cases, better than either of the two previously proposed methods.

Correlated observation errors in data assimilation

Data assimilation provides techniques for combining observations and prior model forecasts to create initial conditions for numerical weather prediction (NWP). The relative weighting assigned to each observation in the analysis is determined by its associated error. Remote sensing data usually has correlated errors, but the correlations are typically ignored in NWP. Here, we describe three approaches to the treatment of observation error correlations. For an idealized data set, the information content under each simplified assumption is compared with that under correct correlation specification. Treating the errors as uncorrelated results in a significant loss of information. However, retention of an approximated correlation gives clear benefits.

Water quality and ecology of the River Lee: mass balance and a review of temporal and spatial data

A regional overview of the water quality and ecology of the River Lee catchment is presented. Specifically, data describing the chemical, microbiological and macrobiological water quality and fisheries communities have been analysed, based on a division into river, sewage treatment works, fish-farm, lake and industrial samples. Nutrient enrichment and the highest concentrations of metals and micro-organics were found in the urbanised, lower reaches of the Lee and in the Lee Navigation. Average annual concentrations of metals were generally within environmental quality standards although, oil many occasions, concentrations of cadmium, copper, lead, mercury and zinc were in excess of the standards. Various organic substances (used as herbicides, fungicides, insecticides, chlorination by-products and industrial solvents) were widely detected in the Lee system. Concentrations of ten micro-organic substances were observed in excess of their environmental quality standards, though not in terms of annual averages. Sewage treatment works were the principal point source input of nutrients. metals and micro-organic determinands to the catchment. Diffuse nitrogen sources contributed approximately 60% and 27% of the in-stream load in the upper and lower Lee respectively, whereas approximately 60% and 20% of the in-stream phosphorus load was derived from diffuse sources in the upper and lower Lee. For metals, the most significant source was the urban runoff from North London. In reaches less affected by effluent discharges, diffuse runoff from urban and agricultural areas dominated trends. Flig-h microbiological content, observed in the River Lee particularly in urbanised reaches, was far in excess of the EC Bathing Water Directive standards. Water quality issues and degraded habitat in the lower reaches of the Lee have led to impoverished aquatic fauna but, within the mid-catchment reaches and upper agricultural tributaries, less nutrient enrichment and channel alteration has permitted more diverse aquatic fauna.

Sequential designs for phase III clinical trials incorporating treatment selection

Most statistical methodology for phase III clinical trials focuses on the comparison of a single experimental treatment with a control. An increasing desire to reduce the time before regulatory approval of a new drug is sought has led to development of two-stage or sequential designs for trials that combine the definitive analysis associated with phase III with the treatment selection element of a phase II study. In this paper we consider a trial in which the most promising of a number of experimental treatments is selected at the first interim analysis. This considerably reduces the computational load associated with the construction of stopping boundaries compared to the approach proposed by Follman, Proschan and Geller (Biometrics 1994; 50: 325-336). The computational requirement does not exceed that for the sequential comparison of a single experimental treatment with a control. Existing methods are extended in two ways. First, the use of the efficient score as a test statistic makes the analysis of binary, normal or failure-time data, as well as adjustment for covariates or stratification straightforward. Second, the question of trial power is also considered, enabling the determination of sample size required to give specified power. Copyright © 2003 John Wiley & Sons, Ltd.

Meta-analysis of individual patient data from randomised trials: a review of methods used in practice

Background: Meta-analyses based on individual patient data (IPD) are regarded as the gold standard for systematic reviews. However, the methods used for analysing and presenting results from IPD meta-analyses have received little discussion. Methods We review 44 IPD meta-analyses published during the years 1999–2001. We summarize whether they obtained all the data they sought, what types of approaches were used in the analysis, including assumptions of common or random effects, and how they examined the effects of covariates. Results: Twenty-four out of 44 analyses focused on time-to-event outcomes, and most analyses (28) estimated treatment effects within each trial and then combined the results assuming a common treatment effect across trials. Three analyses failed to stratify by trial, analysing the data is if they came from a single mega-trial. Only nine analyses used random effects methods. Covariate-treatment interactions were generally investigated by subgrouping patients. Seven of the meta-analyses included data from less than 80% of the randomized patients sought, but did not address the resulting potential biases. Conclusions: Although IPD meta-analyses have many advantages in assessing the effects of health care, there are several aspects that could be further developed to make fuller use of the potential of these time-consuming projects. In particular, IPD could be used to more fully investigate the influence of covariates on heterogeneity of treatment effects, both within and between trials. The impact of heterogeneity, or use of random effects, are seldom discussed. There is thus considerable scope for enhancing the methods of analysis and presentation of IPD meta-analysis.

A score test for binary data with patient non-compliance

A score test is developed for binary clinical trial data, which incorporates patient non-compliance while respecting randomization. It is assumed in this paper that compliance is all-or-nothing, in the sense that a patient either accepts all of the treatment assigned as specified in the protocol, or none of it. Direct analytic comparisons of the adjusted test statistic for both the score test and the likelihood ratio test are made with the corresponding test statistics that adhere to the intention-to-treat principle. It is shown that no gain in power is possible over the intention-to-treat analysis, by adjusting for patient non-compliance. Sample size formulae are derived and simulation studies are used to demonstrate that the sample size approximation holds. Copyright © 2003 John Wiley & Sons, Ltd.

Using historical lesion volume data in the design of a new phase II clinical trial in acute stroke

Background and Purpose-Clinical research into the treatment of acute stroke is complicated, is costly, and has often been unsuccessful. Developments in imaging technology based on computed tomography and magnetic resonance imaging scans offer opportunities for screening experimental therapies during phase II testing so as to deliver only the most promising interventions to phase III. We discuss the design and the appropriate sample size for phase II studies in stroke based on lesion volume. Methods-Determination of the relation between analyses of lesion volumes and of neurologic outcomes is illustrated using data from placebo trial patients from the Virtual International Stroke Trials Archive. The size of an effect on lesion volume that would lead to a clinically relevant treatment effect in terms of a measure, such as modified Rankin score (mRS), is found. The sample size to detect that magnitude of effect on lesion volume is then calculated. Simulation is used to evaluate different criteria for proceeding from phase II to phase III. Results-The odds ratios for mRS correspond roughly to the square root of odds ratios for lesion volume, implying that for equivalent power specifications, sample sizes based on lesion volumes should be about one fourth of those based on mRS. Relaxation of power requirements, appropriate for phase II, lead to further sample size reductions. For example, a phase III trial comparing a novel treatment with placebo with a total sample size of 1518 patients might be motivated from a phase II trial of 126 patients comparing the same 2 treatment arms. Discussion-Definitive phase III trials in stroke should aim to demonstrate significant effects of treatment on clinical outcomes. However, more direct outcomes such as lesion volume can be useful in phase II for determining whether such phase III trials should be undertaken in the first place. (Stroke. 2009;40:1347-1352.)

Active-control trials with binary data: a comparison of methods for testing superiority or non-inferiority using the odds ratio

This paper considers methods for testing for superiority or non-inferiority in active-control trials with binary data, when the relative treatment effect is expressed as an odds ratio. Three asymptotic tests for the log-odds ratio based on the unconditional binary likelihood are presented, namely the likelihood ratio, Wald and score tests. All three tests can be implemented straightforwardly in standard statistical software packages, as can the corresponding confidence intervals. Simulations indicate that the three alternatives are similar in terms of the Type I error, with values close to the nominal level. However, when the non-inferiority margin becomes large, the score test slightly exceeds the nominal level. In general, the highest power is obtained from the score test, although all three tests are similar and the observed differences in power are not of practical importance. Copyright (C) 2007 John Wiley & Sons, Ltd.

Bayesian sample size for exploratory clinical trials incorporating historical data

This paper presents a simple Bayesian approach to sample size determination in clinical trials. It is required that the trial should be large enough to ensure that the data collected will provide convincing evidence either that an experimental treatment is better than a control or that it fails to improve upon control by some clinically relevant difference. The method resembles standard frequentist formulations of the problem, and indeed in certain circumstances involving 'non-informative' prior information it leads to identical answers. In particular, unlike many Bayesian approaches to sample size determination, use is made of an alternative hypothesis that an experimental treatment is better than a control treatment by some specified magnitude. The approach is introduced in the context of testing whether a single stream of binary observations are consistent with a given success rate p(0). Next the case of comparing two independent streams of normally distributed responses is considered, first under the assumption that their common variance is known and then for unknown variance. Finally, the more general situation in which a large sample is to be collected and analysed according to the asymptotic properties of the score statistic is explored. Copyright (C) 2007 John Wiley & Sons, Ltd.

Targeting the cell cycle machinery for the treatment of cardiovascular disease

Cardiovascular disease represents a major clinical problem affecting a significant proportion of the world's population and remains the main cause of death in the UK. The majority of therapies currently available for the treatment of cardiovascular disease do not cure the problem but merely treat the symptoms. Furthermore, many cardioactive drugs have serious side effects and have narrow therapeutic windows that can limit their usefulness in the clinic. Thus, the development of more selective and highly effective therapeutic strategies that could cure specific cardiovascular diseases would be of enormous benefit both to the patient and to those countries where healthcare systems are responsible for an increasing number of patients. In this review, we discuss the evidence that suggests that targeting the cell cycle machinery in cardiovascular cells provides a novel strategy for the treatment of certain cardiovascular diseases. Those cell cycle molecules that are important for regulating terminal differentiation of cardiac myocytes and whether they can be targeted to reinitiate cell division and myocardial repair will be discussed as will the molecules that control vascular smooth muscle cell (VSMC) and endothelial cell proliferation in disorders such as atherosclerosis and restenosis. The main approaches currently used to target the cell cycle machinery in cardiovascular disease have employed gene therapy techniques. We will overview the different methods and routes of gene delivery to the cardiovascular system and describe possible future drug therapies for these disorders. Although the majority of the published data comes from animal studies, there are several instances where potential therapies have moved into the clinical setting with promising results.

Does genotype and equol-production status affect response to isoflavones? Data from a pan-European study on the effects of isoflavones on cardiovascular risk markers in post-menopausal women

The increase in CVD incidence following the menopause is associated with oestrogen loss. Dietary isoflavones are thought to be cardioprotective via their oestrogenic and oestrogen receptor-independent effects, but evidence to support this role is scarce. Individual variation in response to diet may be considerable and can obscure potential beneficial effects in a sample population; in particular, the response to isoflavone treatment may vary according to genotype and equol-production status. The effects of isoflavone supplementation (50hairspmg/d) on a range of established and novel biomarkers of CVD, including markers of lipid and glucose metabolism and inflammatory biomarkers, have been investigated in a placebo-controlled 2x8-week randomised cross-over study in 117 healthy post-menopausal women. Responsiveness to isoflavone supplementation according to (1) single nucleotide polymorphisms in a range of key CVD genes, including oestrogen receptor (ER) alpha and beta and (2) equol-production status has been examined. Isoflavones supplementation was found to have no effect on markers of lipids and glucose metabolism. Isoflavones improve C-reactive protein concentrations but do not affect other plasma inflammatory markers. There are no differences in response to isoflavones according to equol-production status. However, differences in HDL-cholesterol and vascular cell adhesion molecule 1 response to isoflavones v. placebo are evident with specific ER beta genotypes. In conclusion, isoflavones have beneficial effects on C-reactive protein, but not other cardiovascular risk markers. However, specific ER beta gene polymorphic subgroups may benefit from isoflavone supplementation.

Modeling data with structural and temporal correlation using lower level and higher level multilevel models

Novel imaging techniques are playing an increasingly important role in drug development, providing insight into the mechanism of action of new chemical entities. The data sets obtained by these methods can be large with complex inter-relationships, but the most appropriate statistical analysis for handling this data is often uncertain - precisely because of the exploratory nature of the way the data are collected. We present an example from a clinical trial using magnetic resonance imaging to assess changes in atherosclerotic plaques following treatment with a tool compound with established clinical benefit. We compared two specific approaches to handle the correlations due to physical location and repeated measurements: two-level and four-level multilevel models. The two methods identified similar structural variables, but higher level multilevel models had the advantage of explaining a greater proportion of variation, and the modeling assumptions appeared to be better satisfied.