Finite element aided design evolution of composite leaf spring

This paper shows the process of the virtual production development of the mechanical connection between the top leaf of a dual composite leaf spring system to a shackle using finite element methods. The commercial FEA package MSC/MARC has been used for the analysis. In the original design the joint was based on a closed eye-end. Full scale testing results showed that this configuration achieved the vertical proof load of 150 kN and 1 million cycles of fatigue load. However, a problem with delamination occurred at the interface between the fibres going around the eye and the main leaf body. To overcome this problem, a second design was tried using transverse bandages of woven glass fibre reinforced tape to wrap the section that is prone to delaminate. In this case, the maximum interlaminar shear stress was reduced by a certain amount but it was still higher than the material’s shear strength. Based on the fact that, even with delamination, the top leaf spring still sustained the maximum static and fatigue loads required, the third design was proposed with an open eye-end, eliminating altogether the interface where the maximum shear stress occurs. The maximum shear stress predicted by FEA is reduced significantly and a safety factor of around 2 has been obtained. Thus, a successful and safe design has been achieved.

“So the big rocks we put in the jar”: using situated reasoning to coordinate design activity

Ways in which situated reasoning featured in the course of action in the setting of a pair-programming software design exercise is examined, and how interactionally design was accomplished as a coordinated activity in situ.

Directed search with real options

While search is normally modelled by economists purely in terms of decisions over making observations, this paper models it as a process in which information is gained through feedback from innovatory product launches. The information gained can then be used to decide whether to exercise real options. In the model the initial decisions involve a product design and the scale of production capacity. There are then real options to change these factors based on what is learned. The case of launching product variants in parallel is also considered. Under ‘true’ uncertainty, the model can be seen in terms of heuristic decision-making based on subjective beliefs with limited foresight. Search costs, the values of the real options, beliefs, and the cost of capital are all shown to be significant in determining the search path.

Estimating climatically relevant singular vectors for decadal predictions of the Atlantic Ocean

A key aspect in designing an ecient decadal prediction system is ensuring that the uncertainty in the ocean initial conditions is sampled optimally. Here, we consider one strategy to address this issue by investigating the growth of optimal perturbations in the HadCM3 global climate model (GCM). More specically, climatically relevant singular vectors (CSVs) - the small perturbations which grow most rapidly for a specic initial condition - are estimated for decadal timescales in the Atlantic Ocean. It is found that reliable CSVs can be estimated by running a large ensemble of integrations of the GCM. Amplication of the optimal perturbations occurs for more than 10 years, and possibly up to 40 years. The identi ed regions for growing perturbations are found to be in the far North Atlantic, and these perturbations cause amplication through an anomalous meridional overturning circulation response. Additionally, this type of analysis potentially informs the design of future ocean observing systems by identifying the sensitive regions where small uncertainties in the ocean state can grow maximally. Although these CSVs are expensive to compute, we identify ways in which the process could be made more ecient in the future.

Buyer–seller interaction in experimental spatial markets

We report results from experimental spatial markets with endogenous buyer location on a discrete version of Hotelling's linear city. Buyer locations favor more often the hypothesis of transportation cost minimization than that of strategic location aimed at increasing price competition between sellers. However, the latter of the two hypotheses receives systematic support too. Differentiation by seller-subjects is substantially less than the theory would predict for the specific framework used. Our results suggest that location strategies adopted by subjects can be seen as a rational process favoring conservative product design and spatial agglomeration of economic activities.

Rationality and momentum in real estate investment forecasts

This study examines the rationality and momentum in forecasts for rental, capital value and total returns for the real estate investment market in the United Kingdom. In order to investigate if forecasters are affected by the general economic conditions present at the time of forecast we incorporate into the analysis Gross Domestic Product(GDP) and the Default Spread (DS). The empirical findings show high levels of momentum in the forecasts, with highly persistent forecast errors. The results also indicate that forecasters are affected by adverse conditions. This is consistent with the finding that they tend to exhibit greater forecast error when the property market is underperforming and vice-versa.

High pressure intensification of cassava resistant starch (RS3) yields

Cassava starch, typically, has resistant starch type 3 (RS3) content of 2.4%. This paper shows that the RS3 yields can be substantially enhanced by debranching cassava starch using pullulanase followed by high pressure or cyclic high-pressure annealing. RS3 yield of 41.3% was obtained when annealing was carried out at 400 MPa/60°C for 15 min, whereas it took nearly 8 h to obtain the same yield under conventional atmospheric annealing at 60°C. The yield of RS3 could be further significantly increased by annealing under 400MPa/60°C pressure for 15 min followed by resting at atmospheric pressure for 3 h 45 min, and repeating this cycle for up to six times. Microstructural surface analysis of the product under a scanning electron microscope showed an increasingly rigid density of the crystalline structure formed, confirming higher RS3 content.

Statistical design and analysis of pharmacogenetic trials

Pharmacogenetic trials investigate the effect of genotype on treatment response. When there are two or more treatment groups and two or more genetic groups, investigation of gene-treatment interactions is of key interest. However, calculation of the power to detect such interactions is complicated because this depends not only on the treatment effect size within each genetic group, but also on the number of genetic groups, the size of each genetic group, and the type of genetic effect that is both present and tested for. The scale chosen to measure the magnitude of an interaction can also be problematic, especially for the binary case. Elston et al. proposed a test for detecting the presence of gene-treatment interactions for binary responses, and gave appropriate power calculations. This paper shows how the same approach can also be used for normally distributed responses. We also propose a method for analysing and performing sample size calculations based on a generalized linear model (GLM) approach. The power of the Elston et al. and GLM approaches are compared for the binary and normal case using several illustrative examples. While more sensitive to errors in model specification than the Elston et al. approach, the GLM approach is much more flexible and in many cases more powerful. Copyright © 2005 John Wiley & Sons, Ltd.

Design considerations in the sequential analysis of matched case–control data

A role for sequential test procedures is emerging in genetic and epidemiological studies using banked biological resources. This stems from the methodology's potential for improved use of information relative to comparable fixed sample designs. Studies in which cost, time and ethics feature prominently are particularly suited to a sequential approach. In this paper sequential procedures for matched case–control studies with binary data will be investigated and assessed. Design issues such as sample size evaluation and error rates are identified and addressed. The methodology is illustrated and evaluated using both real and simulated data sets.

Analysis of feeding strategies for small-scale dairy systems in central Mexico using linear programming

A limitation of small-scale dairy systems in central Mexico is that traditional feeding strategies are less effective when nutrient availability varies through the year. In the present work, a linear programming (LP) model that maximizes income over feed cost was developed, and used to evaluate two strategies: the traditional one used by the small-scale dairy producers in Michoacan State, based on fresh lucerne, maize grain and maize straw; and an alternative strategy proposed by the LIP model, based on ryegrass hay, maize silage and maize grain. Biological and economic efficiency for both strategies were evaluated. Results obtained with the traditional strategy agree with previously published work. The alternative strategy did not improve upon the performance of the traditional strategy because of low metabolizable protein content of the maize silage considered by the model. However, the Study recommends improvement of forage quality to increase the efficiency of small-scale dairy systems, rather than looking for concentrate supplementation.

The sequential analysis of repeated binary responses: a score test for the case of three time points

In this paper a robust method is developed for the analysis of data consisting of repeated binary observations taken at up to three fixed time points on each subject. The primary objective is to compare outcomes at the last time point, using earlier observations to predict this for subjects with incomplete records. A score test is derived. The method is developed for application to sequential clinical trials, as at interim analyses there will be many incomplete records occurring in non-informative patterns. Motivation for the methodology comes from experience with clinical trials in stroke and head injury, and data from one such trial is used to illustrate the approach. Extensions to more than three time points and to allow for stratification are discussed. Copyright © 2005 John Wiley & Sons, Ltd.

A simple two-stage design for quantitative responses with application to a study in diabetic neuropathic pain

Two-stage designs offer substantial advantages for early phase II studies. The interim analysis following the first stage allows the study to he stopped for futility, or more positively, it might lead to early progression to the trials needed for late phase H and phase III. If the study is to continue to its second stage, then there is an opportunity for a revision of the total sample size. Two-stage designs have been implemented widely in oncology studies in which there is a single treatment arm and patient responses are binary. In this paper the case of two-arm comparative studies in which responses are quantitative is considered. This setting is common in therapeutic areas other than oncology. It will be assumed that observations are normally distributed, but that there is some doubt concerning their standard deviation, motivating the need for sample size review. The work reported has been motivated by a study in diabetic neuropathic pain, and the development of the design for that trial is described in detail. Copyright (C) 2008 John Wiley & Sons, Ltd.