Dynamic shear modulus of isotropic elastomers

We have investigated the dynamic mechanical behavior of two cross-linked polymer networks with very different topologies: one made of backbones randomly linked along their length; the other with fixed-length strands uniformly cross-linked at their ends. The samples were analyzed using oscillatory shear, at very small strains corresponding to the linear regime. This was carried out at a range of frequencies, and at temperatures ranging from the glass plateau, through the glass transition, and well into the rubbery region. Through the glass transition, the data obeyed the time-temperature superposition principle, and could be analyzed using WLF treatment. At higher temperatures, in the rubbery region, the storage modulus was found to deviate from this, taking a value that is independent of frequency. This value increased linearly with temperature, as expected for the entropic rubber elasticity, but with a substantial negative offset inconsistent with straightforward enthalpic effects. Conversely, the loss modulus continued to follow time-temperature superposition, decreasing with increasing temperature, and showing a power-law dependence on frequency.

Structure and rheology of aqueous micellar solutions and gels formed from an associative poly(oxybutylene)-poly(oxyethylene)-poly(oxybutylene) triblock copolymer

The structure and shear flow behaviour of aqueous micellar solutions and gels formed by an amphiphilic poly(oxybutylene)-poly(oxyethylene)-poly(oxybutylene) triblock copolymer with a lengthy hydrophilic poly(oxyethylene) block has been investigated by rheology, small angle neutron scattering (SANS) and small-angle X-ray scattering (SAXS). SANS revealed that bridging of chains between micelles introduces, in the micellar solution, an attractive long-range component which can be described through a potential of interaction corresponding to sticky soft spheres. The strength of the attractive interaction increases with increasing concentration. Rheology showed that the dependence of the storage modulus with temperature can be explained as a function of the micellar bridging, micellisation and phase morphology. SAXS studies showed that the orientation adopted by the system in the get phase under shear is similar to that previously observed by us for the gel phase of a poly(oxyethylene)-poly(oxybutylene) diblock copolymer with a long poly(oxyethylene) chain, suggesting that the micellar corona/core length ratio and not the architecture of the block copolymer influences the alignment of the gel phase under shear.

Effects of variation in the palm stearin: palm olein ratio on the crystallisation of a low-trans shortening

Changes in the theological properties during crystallisation and in the crystal size and morphology of blends containing rapeseed oil with varying percentages of palm stearin (POs) and palm olein (POf) have been studied. The crystals formed from all three blends were studied by confocal laser scanning microscopy, light microscopy and environmental scanning electron microscopy, which revealed the development of clusters of 3-5 individual elementary "spherulites" in the early stages of crystallisation. The saturated triacylglycerol content of the solid crystals separated at the onset of crystallisation was much greater than that in the total fat. Fat blends with a higher content of palm stearin had a more rapid nucleation rate when observed by light microscopy, and this caused an earlier change in the rheological properties of the fat during crystallisation. Using a low torque amplitude (0.005 Pa, which was within the linear viscoelastic region of all samples studied) and a frequency of 1 Hz, the viscoelastic properties of melted fat during cooling were studied. All samples, prior to crystallisation, showed weak viscoelastic liquid behaviour (G '', loss modulus >G', storage modulus). After crystallisation a more "solid like" behaviour was observed (G' similar to or greater than G ''). The blend having the highest concentration of POs was found to have the earliest onset of crystallisation (27% w/w POs; 12 mins, 22% w/w POs; 13.5 mins, 17% w/w POs, 15 mins, respectively). However, there were no significant differences in the time to the point when G' became greater than G' among the three blends. (c) 2006 Elsevier Ltd. All rights reserved.

Effects of composition on fat rheology and crystallisation

The crystallisation behaviour of three fat blends, comprising a commercial shortening, a blend of fats with a very low trans fatty acid content ("low-trans") and a blend including hardened rapeseed oil with a relatively high trans fatty acid content ("high-trans") was studied. Molten fats were lowered to a temperature of 31 degrees C and stirred for 0, 15, 30, 45 and 60 min. Samples were removed and their rheological properties studied, using a controlled stress rheometer, employing a frequency sweep procedure. Effects of the progressive crystallisation at 31 degrees C on the melting profile of fat samples removed from the stirred vessel and solidified at -20 degrees C were also studied by differential scanning calorimetry (DSC). The rheological profiles obtained suggested that all of the fats studied had weak viscoelastic "liquid" structures when melted, but these changed to structures perceived by the rheometer as weak viscoelastic "gels" in the early stages of crystallisation (G' (storage modulus) > G" (loss modulus) over most of the measured frequency range). These subsequently developed into weak viscoelastic semi-solids, showing frequency dependent behaviour on further crystallisation. These changes in behaviour were interpreted as changes from a small number of larger crystals "cross-linking" in a liquid matrix to a larger number of smaller crystals packed with a "slip plane" of liquid oil between them. The rate of crystallisation of the three fats was in the order high trans > low-trans > commercial shortening. Changes in the DSC melting profile due to fractionation of triacylglycerols during the crystallisation at 31 degrees C were evident for all three fats. (c) 2006 Elsevier Ltd. All rights reserved.

Polymer − surfactant vesicular complexes in aqueous medium

The introduction of ionic single-tailed surfactants to aqueous solutions of EO18BO10 [EO = poly(ethylene oxide), BO = poly(1,2-butylene oxide), subscripts denote the number of repeating units] leads to the formation of vesicles, as probed by laser scanning confocal microscopy. Dynamic light scattering showed that the dimensions of these aggregates at early stages of development do not depend on the sign of the surfactant head group charge. Small-angle X-ray scattering (SAXS) analysis indicated the coexistence of smaller micelles of different sizes and varying polymer content in solution. In strong contrast to the dramatic increase of size of dispersed particles induced by surfactants in dilute solution, the d-spacing of corresponding mesophases reduces monotonically upon increasing surfactant loading. This effect points to the suppression of vesicles as a consequence of increasing ionic strength in concentrated solutions. Maximum enhancements of storage modulus and thermal stability of hybrid gels take place at different compositions, indicating a delicate balance between the number and size of polymer-poor aggregates (population increases with surfactant loading) and the number and size of polymer−surfactant complexes (number and size decrease in high surfactant concentrations).

Effects of addition of phenolic compounds on the acid gelation of milk

Tannic acid (0.1–1%, w/w) and gallic acid (0.3–1%, w/w) were added to skim milk prior to acidification with GDL. The acid gelation of tannic and gallic acid fortified milk had a faster gelation time in comparison with the control gel without phenolic compounds. The addition of tannic acid and gallic acid (up to 0.8%) to the milk resulted in a higher storage modulus (G′), decrease in the water mobility (T2 time) and had no significant effect on the syneresis index (SI). However, the inclusion of 1% gallic acid resulted in a significant decrease in G′, a significant increase in the SI and a wider T2 distribution. Lowering the temperature of the gels from 30 to 5 °C caused the G′ for the gels with gallic and tannic acid to increase significantly in comparison with the control, possibly due to increased hydrogen bonding in the presence of phenolic compounds

Microbiological, chemical and rheological properties of low fat set yoghurt produced with exopolysaccharide (EPS) producing Bifidobacterium strains.

In this work, the microbiological and physicochemical differences of three types of low fat set yoghurts were studied, as well as the changes taking place during storage at 4 °C for 28 days. The first yoghurt was produced with yoghurt starters and exopolysaccharide (EPS) producing Bifidobacterium longum subsp. infantis CCUG 52486 (CCUGY), the second with yoghurt starters and Bifidobacterium infantis NCIMB 702205 (NCIMBY) and the third with just yoghurt starters (control yoghurt). No significant differences were observed in terms of cell concentrations; for all three yoghurts, similar final cell concentrations were obtained for the yoghurt starter cultures (~7.5 log cfu g−1) and the Bifidobacterium strains (~7.8 log cfu g−1). Both Bifidobacterium survived well during storage, as in both cases the cell viability decreased by less than 0.5 log cfu g−1after 28 days of storage. A decrease in pH followed by an increase in lactic acid was observed during storage for all three yoghurts, which was mostly attributed to the activity of the yoghurt starter cultures. The two yoghurts with the EPS producing Bifidobacterium strains exhibited lower syneresis than the control yoghurt. The lowest was shown by CCUGY, which also exhibited the highest storage modulus and firmness, and a well defined porous web-like structure in cryo-SEM. Examination of the micro-structure of the yoghurts using cryo-scanning electron microscopy (cryo-SEM) indicated that the above observations were due to the interaction between the EPS and the milk proteins. Overall, the results indicated that the EPS producing Bifidobacterium longum subsp. infantis CCUG 52486 is the most promising strain, and can be used with yoghurt starter cultures to manufacture low fat set yoghurt with probiotic activities and at the same time enhanced physicochemical and rheological properties.

Resonance response of electrorheological fluids in vertical oscillation squeeze flow

The resonance effect of microcrystalline cellulose/castor oil electrorheological (ER) suspensions was studied in a compressed oscillatory squeeze flow under external electric fields. The resonance frequency first increases linearly with increasing external held, and then shift to high-field plateau. The amplitudes of resonance peak increase sharply with the applied fields in the range of 0.17-1.67kV/mm. The phase difference of the reduced displacement relative to the excitation force inverses in the case of resonance. A viscoelasticity model of the ER suspensions, which offers both the equivalent stiffness and the viscous damping, should be responsible for the appearance of resonance. The influence of the electric field on the resonance frequency and the resonance hump is consistent qualitatively with the interpretation of our proposed model. Storage modulus G' was presented for the purpose of investigating this influence.

Squeeze flow viscoelasticity of electrorheological fluids based on microcrystalline cellulose

Dynamic viscoelasticity of electrorheological fluids based on microcrystalline cellulose/castor oil suspensions was experimentally investigated in squeeze flow. The dependence of storage modulus G' and loss modulus G" parallel to external electric field on electric fields and strain amplitudes is presented. The experiments show that, when external electric field is higher than the critical field, the viscoelasticity of the ER fluids converts from linear to nonlinear, and the ER fluids transfer from solid-like state to fluid state with the growth of strain amplitude. The influences of strain amplitude and oscillatory frequency on the nonlinearity of viscoelasticity were also studied.

An adhesive elastomeric supramolecular polyurethane healable at body temperature

In this paper, we report the synthesis and healing ability of a non-cytotoxic supramolecular polyurethane network whose mechanical properties can be recovered efficiently (> 99%) at the temperature of the human body (37 ºC). Rheological analysis revealed an acceleration in the drop of the storage modulus above 37 ºC, on account of the dissociation of the supramolecular polyurethane network, and this decrease in viscosity enables the efficient recovery of the mechanical properties. Microscopic and mechanical characterisation has shown that this material is able to recover mechanical properties across a damage site with minimal contact required between the interfaces and also demonstrated that the mechanical properties improved when compared to other low temperature healing elastomers or gel-like materials. The supramolecular polyurethane was found to be non-toxic in a cytotoxicity assay carried out in human skin fibroblasts (cell viability > 94% and non-significantly different compared to the untreated control). This supramolecular network material also exhibited excellent adhesion to pig skin and could be healed completely in situ post damage indicating that biomedical applications could be targeted, such as artificial skin or wound dressings with supramolecular materials of this type.

Variation in dynamic elastic shear modulus of sandstone upon fluid saturation and substitution

Experimental acoustic measurements on sandstone rocks at both sonic and ultrasonic frequencies show that fluid saturation can cause a noticeable change in both the dynamic bulk and shear elastic moduli of sandstones. We observed that the change in dynamic shear modulus upon fluid saturation is highly dependent on the type of saturant, its viscosity, rock microstructure, and applied pressures. Frequency dispersion has some influence on dynamic elastic moduli too, but its effect is limited to the ultrasonic frequency ranges and above. We propose that viscous coupling, reduction in free surface energy, and, to a limited extent, frequency dispersion due to both local and global flow are the main mechanisms responsible for the change in dynamic shear elastic modulus upon fluid saturation and substitution, and we quantify influences.

Effects of solar wind magnetosphere coupling recorded at different geomagnetic latitudes: Separation of directly-driven and storage/release systems

The effect on geomagnetic activity of solar wind speed, compared with that of the strength of the interplanetary magnetic field, differs with geomagnetic latitude. In this study we construct a new index based on monthly standard deviations in the H-component of the geomagnetic field for all geomagnetic latitudes. We demonstrate that for this index the response at auroral regions correlates best with interplanetary coupling functions which include the solar wind speed while mid- and low-latitude regions respond to variations in the interplanetary magnetic field strength. These results are used to isolate the responsible geomagnetic current systems.

Microbial relatives of the seed storage proteins of higher plants: conservation of structure and diversification of function during evolution of the cupin superfamily.

This review summarizes the recent discovery of the cupin superfamily (from the Latin term "cupa," a small barrel) of functionally diverse proteins that initially were limited to several higher plant proteins such as seed storage proteins, germin (an oxalate oxidase), germin-like proteins, and auxin-binding protein. Knowledge of the three-dimensional structure of two vicilins, seed proteins with a characteristic beta-barrel core, led to the identification of a small number of conserved residues and thence to the discovery of several microbial proteins which share these key amino acids. In particular, there is a highly conserved pattern of two histidine-containing motifs with a varied intermotif spacing. This cupin signature is found as a central component of many microbial proteins including certain types of phosphomannose isomerase, polyketide synthase, epimerase, and dioxygenase. In addition, the signature has been identified within the N-terminal effector domain in a subgroup of bacterial AraC transcription factors. As well as these single-domain cupins, this survey has identified other classes of two-domain bicupins including bacterial gentisate 1, 2-dioxygenases and 1-hydroxy-2-naphthoate dioxygenases, fungal oxalate decarboxylases, and legume sucrose-binding proteins. Cupin evolution is discussed from the perspective of the structure-function relationships, using data from the genomes of several prokaryotes, especially Bacillus subtilis. Many of these functions involve aspects of sugar metabolism and cell wall synthesis and are concerned with responses to abiotic stress such as heat, desiccation, or starvation. Particular emphasis is also given to the oxalate-degrading enzymes from microbes, their biological significance, and their value in a range of medical and other applications.

Barley oxalate oxidase is a hexameric protein related to seed storage proteins: evidence from X-ray crystallography

The oxalate oxidase enzyme expressed in barley roots is a thermostable, protease-resistant enzyme that generates H2O2. It has great medical importance because of its use to assay plasma and urinary oxalate, and it has also been used to generate transgenic, pathogen-resistant crops. This protein has now been purified and three types of crystals grown. X-ray analysis shows that the symmetry present in these crystals is consistent with a hexameric arrangement of subunits, probably a trimer of dimers. This structure may be similar to that found in the related seed storage proteins.