The effect of free Ca2+ on the heat stability and other characteristics of low-heat skim milk powder

Low-heat skim milk powder (SMP), reconstituted to 25% total solids, was found to have poor heat stability. This could be improved by reducing the free Ca2+ concentration to 1.14 mm, or lower, by the addition of either Amberlite IR-120 ion-exchange resin in its sodium form or tri-sodium citrate in skim milk prior to evaporation and spray drying. Reduction in Ca2+ concentration was accompanied by increases in pH, particle size, and kinematic viscosity, and by a reduction in zeta-potential and changes in colour. In-container sterilisation of the reconstituted powder increased particle size, zeta-potential, kinematic viscosity and a* and b* values. However. Ca2+ concentration, pH and whiteness decreased. This study elucidated the importance of Ca2+ concentration and pH on heat stability of low-heat SMP, suggesting that Ca2+ concentration and pH in bulk milk are useful indicators for ensuring that spray dried milk powder has good heat stability. (C) 2009 Elsevier Ltd. All rights reserved.

Effect of seasonal variation on the properties of whipping cream, soft cheese and skim milk powder in the UK

Whipping cream, skim milk powder and soft cheese were produced throughout the year. Whipping cream manufactured in spring and winter produced significantly higher overrun and better serum stability, and whipping time was related to buffering capacity of raw milk. Heat stability of reconstituted skim milk powder (RSMP) at 9% TS was greater in summer and autumn, and greater than 25% TS throughout the year. It was positively related to the protein content of raw milk, but negatively with fat. In contrast to other dairy products, no significant effect of season on the properties of soft cheese was found.

Assessment of the quality of cottage cheese produced from standard and protein-fortified skim milk

The effects of milk protein fortification on the texture and microstructure of cottage cheese curd were evaluated. Protein powder (92.6% protein) was added to the skim milk at a level of 0.4% (w/w) to produce curds. Control curds with no protein powder addition were also produced. These curds were analysed for differences in yield, total solids, curd size, texture and structure. It was found that the addition of protein powder contributed to a significant yield increase, which can be attributed to increased water retention, with better curd size distribution. Control curds were firmer than the fortified curds and the structure showed less open-pore structure as revealed by electron microscopy. However, the addition of dressing masked the textural differences, and a sensory panel was unable to distinguish between cheeses produced from fortified milk and controls.

A comparison of reverse osmosis, nanofiltration and ultrafiltration as concentration processes for skim milk prior to drying

Skim milk was concentrated by reverse osmosis (RO), nanofiltration (NF) and ultrafiltration (UF) and the retentates were spray-dried. The resulting powders were reconstituted to 25% TS and sterilised to evaluate their heat stability. Reverse osmosis led to maximum retention of calcium, a fall in pH for its retentate and its reconstituted powder. All RO powders produced a weak gel on heating. Some calcium was lost during NF and a greater amount during UF. Their resulting reconstituted powders had a higher pH than those produced by RO. Powders produced by UF showed poor heat stability. Only one powder produced by NF showed good heat stability. This could be improved by addition of stabilisers at appropriate addition rates.

Effect of dairy-based protein sources and temperature on growth, acidification and exopolysaccharide production of Bifidobacterium strains in skim milk

The aim of the present study was to find out the best growing conditions for exopolysaccharide (EPS) producing bifidobacteria, which improve their functionality in yoghurt-like products. Two Bifidobacterium strains were used in this study, Bifidobacterium longum subsp. infantis CCUG 52486 and Bifidobacterium infantis NCIMB 702205. In the first part of the study the effect of casein hydrolysate, lactalbumin hydrolysate, whey protein concentrate and whey protein isolate, added at 1.5% w/v in skim milk, was evaluated in terms of cell growth and EPS production; skim milk supplemented with yeast extract served as the control. Among the various nitrogen sources, casein hydrolysate (CH) showed the highest cell growth and EPS production for both strains after 18 h incubation and therefore it was selected for subsequent work. Based on fermentation experiments using different levels of CH (from 0.5 to 2.5% w/v) it was deduced that 1.5% (w/v) CH resulted in the highest EPS production, yielding 102 and 285 mg L− 1 for B. infantis NCIMB 702205 and B. longum subsp. infantis CCUG 52486, respectively. The influence of temperature on growth and EPS production of both strains was further evaluated at 25, 30, 37 and 42 °C for up to 48 h in milk supplemented with 1.5% (w/v) CH. The temperature had a significant effect on growth, acidification and EPS production. The maximum growth and EPS production were recorded at 37 °C for both strains, whereas no EPS production was observed at 25 °C. Lower EPS production for both strains were observed at 42 °C, which is the common temperature used in yoghurt manufacturing compared to that at 37 °C. The results showed that the culture conditions have a clear effect on the growth, acidification and EPS production, and more specifically, that skim milk supplemented with 1.5% (w/v) CH could be used as a substrate for the growth of EPS-producing bifidobacteria, at 37 °C for 24 h, resulting in the production of a low fat yoghurt-like product with improved functionality.

A novel technique for differentiation of proteins in the development of acid gel structure from control and heat treated milk using confocal scanning laser microscopy

The incorporation of caseins and whey proteins into acid gels produced from unheated and heat treated skimmed milk was studied by confocal scanning laser microscopy (CSLM) using fluorescent labelled proteins. Bovine casein micelles were labelled using Alexa Fluor 594, while whey proteins were labelled using Alexa Fluor 488. Samples of the labelled protein solutions were introduced into aliquots of pasteurised skim milk, and skim milk heated to 90 degrees C for 2 min and 95 degrees C for 8 min. The milk was acidified at 40 degrees C to a final pH of 4.4 using 20 g gluconodelta-lactone/l (GDL). The formation of gels was observed with CSLM at two wavelengths (488 nm and 594 nm), and also by visual and rheological methods. In the control milk, as pH decreased distinct casein aggregates appeared, and as further pH reduction occurred, the whey proteins could be seen to coat the casein aggregates. With the heated milks, the gel structure was formed of continuous strands consisting of both casein and whey protein. The formation of the gel network was correlated with an increase in the elastic modulus for all three treatments, in relation to the severity of heat treatment. This model system allows the separate observation of the caseins and whey proteins, and the study of the interactions between the two protein fractions during the formation of the acid gel structure, on a real-time basis. The system could therefore be a valuable tool in the study of structure formation in yoghurt and other dairy protein systems.

Effects of addition of phenolic compounds on the acid gelation of milk

Tannic acid (0.1–1%, w/w) and gallic acid (0.3–1%, w/w) were added to skim milk prior to acidification with GDL. The acid gelation of tannic and gallic acid fortified milk had a faster gelation time in comparison with the control gel without phenolic compounds. The addition of tannic acid and gallic acid (up to 0.8%) to the milk resulted in a higher storage modulus (G′), decrease in the water mobility (T2 time) and had no significant effect on the syneresis index (SI). However, the inclusion of 1% gallic acid resulted in a significant decrease in G′, a significant increase in the SI and a wider T2 distribution. Lowering the temperature of the gels from 30 to 5 °C caused the G′ for the gels with gallic and tannic acid to increase significantly in comparison with the control, possibly due to increased hydrogen bonding in the presence of phenolic compounds

Emulsifying, rheological and physicochemical properties of exopolysaccharide produced by Bifidobacterium longum subsp. infantis CCUG 52486 and Bifidobacterium infantis NCIMB 702205

The rheological, emulsification and certain physicochemical properties of purified exopolysaccharides (EPS) of Bifidobacterium longum subsp. infantis CCUG 52486 and Bifidobacterium infantis NCIMB 702205 were studied and compared with those of guar gum and xanthan gum. The two strains were grown in skim milk supplemented with 1.5% (w/v) casein hydrolysate at 37 ◦C for 24 h; they both produced heteropolysaccharides with different molecular mass and composition. The carbohydrate content of both polymers was more than 92% and no protein was detected. The EPS of B. longum subsp. infantis CCUG 52486 showed highly branched entangled porous structure under scanning electron microscopy. Higher intrinsic viscosity was observed for the EPS of B. longum subsp. infantis CCUG 52486 compared to the EPS of B. infantis NCIMB 702205 and guar gum. Both polymers showed pseudoplastic non-Newtonian fluid behaviour in an aqueous solution. The EPS of B. infantis NCIMB 702205 and B. longum subsp. infantis CCUG 52486 produced more stable emulsions with orange oil, sunflower seed oil, coconut oil and xylene compared to guar and xanthan gum. The EPS of B. longum subsp. infantis CCUG 52486 is the most promising one for applications in the food industry, as it had higher intrinsic viscosity, higher apparent viscosity in aqueous solution, porous dense entangled structure and good emulsification activity.

Short communication: estimation of the financial benefit of using Jersey milk at different inclusion rates for Cheddar cheese production using partial budgeting

Partial budgeting was used to estimate the net benefit of blending Jersey milk in Holstein-Friesian milk for Cheddar cheese production. Jersey milk increases Cheddar cheese yield. However, the cost of Jersey milk is also higher; thus, determining the balance of profitability is necessary, including consideration of seasonal effects. Input variables were based on a pilot plant experiment run from 2012 to 2013 and industry milk and cheese prices during this period. When Jersey milk was used at an increasing rate with Holstein-Friesian milk (25, 50, 75, and 100% Jersey milk), it resulted in an increase of average net profit of 3.41, 6.44, 8.57, and 11.18 pence per kilogram of milk, respectively, and this additional profit was constant throughout the year. Sensitivity analysis showed that the most influential input on additional profit was cheese yield, whereas cheese price and milk price had a small effect. The minimum increase in yield, which was necessary for the use of Jersey milk to be profitable, was 2.63, 7.28, 9.95, and 12.37% at 25, 50, 75, and 100% Jersey milk, respectively. Including Jersey milk did not affect the quantity of whey butter and powder produced. Althoug further research is needed to ascertain the amount of additional profit that would be found on a commercial scale, the results indicate that using Jersey milk for Cheddar cheese making would lead to an improvement in profit for the cheese makers, especially at higher inclusion rates.

Structure determination from powder diffraction data

Advances made over the past decade in structure determination from powder diffraction data are reviewed with particular emphasis on algorithmic developments and the successes and limitations of the technique. While global optimization methods have been successful in the solution of molecular crystal structures, new methods are required to make the solution of inorganic crystal structures more routine. The use of complementary techniques such as NMR to assist structure solution is discussed and the potential for the combined use of X-ray and neutron diffraction data for structure verification is explored. Structures that have proved difficult to solve from powder diffraction data are reviewed and the limitations of structure determination from powder diffraction data are discussed. Furthermore, the prospects of solving small protein crystal structures over the next decade are assessed.

GDASH: a grid-enabled program for structure solution from powder diffraction data

The simulated annealing approach to structure solution from powder diffraction data, as implemented in the DASH program, is easily amenable to parallelization at the individual run level. Very large scale increases in speed of execution can therefore be achieved by distributing individual DASH runs over a network of computers. The GDASH program achieves this by packaging DASH in a form that enables it to run under the Univa UD Grid MP system, which harnesses networks of existing computing resources to perform calculations.

MDASH: a multi-core-enabled program for structure solution from powder diffraction data

The simulated annealing approach to structure solution from powder diffraction data, as implemented in the DASH program, is easily amenable to parallelization at the individual run level. Modest increases in speed of execution can therefore be achieved by executing individual DASH runs on the individual cores of CPUs.

Selenium supplementation of lactating dairy cows: effects on milk production and total selenium content and speciation in blood, milk and cheese

Forty-multiparous Holstein cows were used in a 16-wk continuous design study to determine the effects of either selenium (Se) source, selenized yeast (SY) (derived from a specific strain of Saccharomyces cerevisiae CNCM I-3060 Sel-Plex®) or sodium selenite (SS), or inclusion rate of SY on Se concentration and speciation in blood, milk and cheese. Cows received ad libitum a TMR with 1:1 forage:concentrate ratio on a dry matter (DM) basis. There were four diets (T1-T4) which differed only in either source or dose of Se additive. Estimated total dietary Se for T1 (no supplement), T2 (SS), T3 (SY) and T4 (SY) was 0.16, 0.30, 0.30 and 0.45 mg/kg DM, respectively. Blood and milk samples were taken at 28 day intervals and at each time point there were positive linear effects of SY on Se concentration in blood and milk. At day 112 blood and milk Se values for T1-T4 were 177, 208, 248, 279 ± 6.6 and 24, 38, 57, 72 ± 3.7 ng/g fresh material, respectively and indicate improved uptake and incorporation of Se from SY. While selenocysteine (SeCys) was the main selenised amino acid in blood its concentration was not markedly affected by treatment, but the proportion of total Se as selenomethionine (SeMet) increased with increasing inclusion rate of SY. In milk, there were no marked treatment effects on SeCys content, but Se source had a marked effect on the proportion of total Se as SeMet. At day 112 replacing SS (T2) with SY (T3) increased the SeMet concentration of milk from 36 to 111 ng Se/g and its concentration increased further to 157 ng Se/g as the inclusion rate of SY increased further (T4) to provide 0.45 mg Se/kg TMR. Neither Se source nor inclusion rate effected the keeping quality of milk. At day 112, milk from T1, T2, and T3 was made into a hard cheese and Se source had a marked effect on total Se and the proportion of total Se comprised as either SeMet or SeCys. Replacing SS (T2) with SY (T3) increased total Se, SeMet and SeCys content from 180 to 340 ng Se/g, 57 to 153 ng Se/g and 52 to 92 ng Se/g, respectively. Key words: dairy cow, milk and cheese, selenomethionine, selenocysteine, milk keeping quality

Selenium supplementation of lactating dairy cows: Effect on selenium concentration in blood, milk, urine and feces

The objectives were to determine effects of graded levels of selenized yeast derived from a specific strain of Saccharomyces cerevisiae (CNCM I-3060) on animal performance and in selenium concentrations in the blood, milk, feces, and urine of dairy cows compared with sodium selenite; and to provide preliminary data on the proportion of selenium as selenomethionine in the milk and blood. Twenty Holstein cows were used in a 5 × 5 Latin square design study in which all cows received the same total mixed rations, which varied only in source or concentration of dietary selenium. There were 5 experimental treatments. Total dietary selenium of treatment 1, which received no added selenium, was 0.15 mg/kg of dry matter, whereas values for treatments 2, 3, and 4, derived from selenized yeast, were 0.27, 0.33, and 0.40 mg/kg of dry matter, respectively. Treatment 5 contained 0.25 mg of selenium obtained from sodium selenite/kg of dry matter. There were no significant treatment effects on animal performance, and blood chemistry and hematology showed few treatment effects. Regression analysis noted significant positive linear effects of increasing dietary selenium derived from selenized yeast on selenium concentrations in the milk, blood, urine, and feces. In addition, milk selenium results indicated improved bioavailability of selenium from selenized yeast, compared with sodium selenite. Preliminary analyses showed that compared with sodium selenite, the use of selenized yeast increased the concentration of selenomethionine in the milk and blood. There was no indication of adverse effects on cow health associated with the use of selenized yeast.

The effect of calcium removal from milk on casein micelle stability and structure

The total calcium level of raw skimmed milk was reduced by 10, 19, 29, 40 and 51% using Duolite® ion-exchange resin. The products were examined for concentrations of ionic calcium, sodium and potassium and the pH, ethanol stability, micelle diameter and ζ-potential were also measured. Ionic calcium decreased with removal of calcium and pH increased. Calcium removal resulted in an increase in the ethanol stability from 88% to above 100%. Casein micelle diameter increased as calcium was removed. The ζ-potential of the skimmed bulk milk was -24.4 mV, gradually becoming more negative with calcium removal to -30.6 mV after 51% calcium removal. The milk became more translucent as calcium was removed. To investigate the reversibility of this process, calcium chloride was added back to the depleted samples to restore their original total calcium content. At 51% removal, restoration of the total calcium level resulted in formation of clots. At levels of 10 and 19% calcium removal, the ethanol stability remained above 100%, but at higher levels of calcium removal the alcohol stability was adversely affected when the calcium was added back. Adding back calcium resulted in partial restoration of the original casein micelle diameter.