Predictions of some product parameters based on the processing conditions of ultra-high-temperature milk plants

The temperature-time profiles of 22 Australian industrial ultra-high-temperature (UHT) plants and 3 pilot plants, using both indirect and direct heating, were surveyed. From these data, the operating parameters of each plant, the chemical index C*, the bacteriological index B* and the predicted changes in the levels of beta-lactoglobulin, alpha-lactalbumin, lactulose, furosine and browning were determined using a simulation program based on published formulae and reaction kinetics data. There was a wide spread of heating conditions used, some of which resulted in a large margin of bacteriological safety and high chemical indices. However, no conditions were severe enough to cause browning during processing. The data showed a clear distinction between the indirect and direct heating plants. They also indicated that degree of denaturation of alpha-lactalbumin varied over a wide range and may be a useful discriminatory index of heat treatment. Application of the program to pilot plants illustrated its value in determining processing conditions in these plants to simulate the conditions in industrial UHT plants. (C) 2008 Elsevier Ltd. All rights reserved.

Optimisation of the extraction and processing conditions of chamomile (Matricaria chamomilla L.) for incorporation into a beverage

The total phenols, apigenin 7-glucoside, turbidity and colour of extracts from dried chamomile flowers were studied with a view to develop chamomile extracts with potential anti-inflammatory properties for incorporation into beverages. The extraction of all constituents followed pseudo first-order kinetics. In general, the rate constant (k) increased as the temperature increased from 57 to 100 °C. The turbidity only increased significantly between 90 and 100 °C. Therefore, aqueous chamomile extracts had maximum total phenol concentration and minimum turbidity when extracted at 90 °C for 20 min. The effect of drying conditions on chamomile extracted using these conditions was determined. A significant reduction in phenol concentration, from 19.7 ± 0.5 mg/g GAE in fresh chamomile to 13 ± 1 mg/g GAE, was found only in the plant material oven-dried at 80 °C (p ⩽ 0.05). The biggest colour change was between fresh chamomile and that oven-dried at 80 °C, followed by samples air-dried. There was no significant difference in colour of material freeze-dried and oven-dried at 40 °C.

New mathematical modeling approach for predicting microbial inactivation by high hydrostatic pressure

A new primary model based on a thermodynamically consistent first-order kinetic approach was constructed to describe non-log-linear inactivation kinetics of pressure-treated bacteria. The model assumes a first-order process in which the specific inactivation rate changes inversely with the square root of time. The model gave reasonable fits to experimental data over six to seven orders of magnitude. It was also tested on 138 published data sets and provided good fits in about 70% of cases in which the shape of the curve followed the typical convex upward form. In the remainder of published examples, curves contained additional shoulder regions or extended tail regions. Curves with shoulders could be accommodated by including an additional time delay parameter and curves with tails shoulders could be accommodated by omitting points in the tail beyond the point at which survival levels remained more or less constant. The model parameters varied regularly with pressure, which may reflect a genuine mechanistic basis for the model. This property also allowed the calculation of (a) parameters analogous to the decimal reduction time D and z, the temperature increase needed to change the D value by a factor of 10, in thermal processing, and hence the processing conditions needed to attain a desired level of inactivation; and (b) the apparent thermodynamic volumes of activation associated with the lethal events. The hypothesis that inactivation rates changed as a function of the square root of time would be consistent with a diffusion-limited process.

On-line prediction of cheese making using backscatter of near infrared indices light

The potential of a fibre optic sensor, detecting light backscatter in a cheese vat during coagulation and syneresis, to predict curd moisture, fat loses and curd yield was examined. Temperature, cutting time and calcium levels were varied to assess the strength of the predictions over a range of processing conditions. Equations were developed using a combination of independent variables, milk compositional and light backscatter parameters. Fat losses, curd yield and curd moisture content were predicted with a standard error of prediction (SEP) of +/- 2.65 g 100 g(-1) (R-2 = 0.93), +/- 0.95% (R-2 = 0.90) and +/- 1.43% (R-2 = 0.94), respectively. These results were used to develop a model for predicting curd moisture as a function of time during syneresis (SEP = +/- 1.72%; R-2 = 0.95). By monitoring coagulation and syneresis, this sensor technology could be employed to control curd moisture content, thereby improving process control during cheese manufacture. (c) 2007 Elsevier Ltd. All rights reserved..

Effects of gelation temperature on the mozzarella-type curd made from buffalo and cows’ milk: 2. curd yield, overall quality & casein fractions

Buffalo curd gave higher amount of yield than cows’ curd at similar processing conditions. Curd moisture was decreased with the increase of gelation temperatures in both types of milk. Curd cutting time of 45 minutes was found optimum for Mozzarella cheese making from both milk samples. Centrifugation method is simpler, quicker and more reproducible than Buchner funnel method. Buffalo milk contains higher amounts of αs1- , β- and к-casein as compared to cows’ milk.

Interaction of heat-moisture conditions and physical properties in oat processing: II. Flake quality

Product quality is an important determinant of consumer acceptance. Consistent oat flake properties are thus necessary in the mill as well as in the marketplace. The effects of kilning and tempering conditions (30, 60 or 90 min at 80, 95 or 110 degrees C) on flake peroxidase activity, size, thickness, strength and water absorption were therefore determined. After kilning, some peroxidase activity remained but steaming and tempering effectively destroyed the activity of these enzymes. Thus the supposed protective effect of kilning or groat durability was not confirmed. Kilning resulted in an increase in flake specific weight, but no other significant effect on flake quality was observed. Tempering time and temperature interacted significantly to produce complex effects on flake specific weight, thickness and water absorption. Flake thickness and specific weight were significantly correlated (r = 0.808, n = 54). Longer tempering times resulted in an increased fines' fraction, from 1.45% at 30 min to 1.75% at 90 min. It is concluded that whilst kilning has little effect on flake quality, the heat treatment immediately prior to flaking, can be used to adjust flake quality independently of flake thickness.

Interaction of heat-moisture conditions and physical properties in oat processing: I. Mechanical properties of steamed oat groats

Research interest in oats has focussed on their nutritional value, but there have been few studies of their food processing. Heat treatment is characteristic of oat processing, as it is needed to inactivate lipase and to facilitate flaking. A Texture Analyser was used to characterise the mechanical properties of unkilned and kilned oat groats after steaming and tempering in an oven for 30, 60 and 90 min at 80, 95 and 110 degrees C. Maximum force, number of peaks before maximum and final force after 5s hold were used to characterise the behaviour of the groats during compression. Kilned groats were larger and softer before steaming. After steaming and tempering, the moisture content of the kilned groats was higher than for unkilned groats. Hot, steamed oats were softer than cold, unsteamed groats, indicated by a decrease in maximum force from 59 to 55 N, and there was no significant difference between kilned and unkilned groats. However, higher temperatures during tempering increased maximum force. These results suggest that mild steam treatment yields softer oat groats, whereas cold or over-treated groats tend to be harder. (c) 2007 Elsevier Ltd. All rights reserved.

Influence of some processing and storage conditions on the mechanical properties of oat flakes

Flake breakage and texture are important quality, criteria in oat flakes. These properties are determined by the mechanical properties of the flakes, which may be influenced by process variables such as kilning and flake thickness. A pin deformation method was used to measure the rupture force of individual oat flakes at different water activities. The monolayer value of ground oat flakes ranged from 5.83 to 684 g/100 g dry matter Thick flakes were strongest, requiring 3.4 N to rupture the flake compared to 2.2 N for the thin flakes. Water softened the flakes, causing a decrease in rupture force from 3.6 N to 2.4 N as water activity; increased from 0.115 to 0.848. Kilning had a significant effect on flake thickness but not on the mechanical properties. This study suggests that oat flakes should be stored at water activity 0.4 or less as there is a sharp loss of flake strength above this point.

Multivariate analysis of phenol mineralisation by combined hydrodynamic cavitation and heterogeneous advanced Fenton processing

Phenolic compounds in wastewaters are difficult to treat using the conventional biological techniques such as activated sludge processes because of their bio-toxic and recalcitrant properties and the high volumes released from various chemical, pharmaceutical and other industries. In the current work, a modified heterogeneous advanced Fenton process (AFP) is presented as a novel methodology for the treatment of phenolic wastewater. The modified AFP, which is a combination of hydrodynamic cavitation generated using a liquid whistle reactor and the AFP is a promising technology for wastewaters containing high organic content. The presence of hydrodynamic cavitation in the treatment scheme intensifies the Fenton process by generation of additional free radicals. Also, the turbulence produced during the hydrodynamic cavitation process increases the mass transfer rates as well as providing better contact between the pseudo-catalyst surfaces and the reactants. A multivariate design of experiments has been used to ascertain the influence of hydrogen peroxide dosage and iron catalyst loadings on the oxidation performance of the modified AFP. High er TOC removal rates were achieved with increased concentrations of hydrogen peroxide. In contrast, the effect of catalyst loadings was less important on the TOC removal rate under conditions used in this work although there is an optimum value of this parameter. The concentration of iron species in the reaction solution was measured at 105 min and its relationship with the catalyst loadings and hydrogen peroxide level is presented.

Formation of high levels of acrylamide during the processing of flour derived from sulfate-deprived wheat

When wheat was grown under conditions of severe sulfate depletion, dramatic increases in the concentration of free asparagine were found in the grain of up to 30 times as compared to samples receiving the normal levels of sulfate fertilizer. The effect was observed both in plants grown in pots, where the levels of nutrients were carefully controlled, and in plants grown in field trials on soil with poor levels of natural nutrients where sulfate fertilizer was applied at levels from 0 to 40 kg sulfur/Ha. Many of the other free amino acids were present at higher levels in the sulfate-deprived wheat, but the levels of free glutamine showed increases similar to those observed for asparagine. In baked cereal products, asparagine is the precursor of the suspect carcinogen acrylamide, and when flours from the sulfate-deprived wheat were heated at 160 degrees C for 20 min, levels of acrylamide between 2600 and 5200 mu g/kg were found as compared to 600-900 mu g/kg in wheat grown with normal levels of sulfate fertilization.

The use of colloidal gas aphrons as novel downstream processing for the recovery of astaxanthin from cells of Phaffia rhodozyma

BACKGROUND: There is an increasing interest in obtaining natural products with bioactive properties, using fermentation technology. However, the downstream processing consisting of multiple steps can be complicated, leading to increase in the final cost of the product. Therefore there is a need for integrated, cost-effective and scalable separation processes. RESULTS: The present study investigates the use of colloidal gas aphrons (CGA), which are surfactant-stabilized microbubbles, as a novel method for downstream processing. More particularly, their application for the recovery of astaxanthin from the cells of Phaffia rhodozyma is explored. Research carried out with standard solutions of astaxanthin and CGA generated from the cationic surfactant hexadecyl. trimethyl ammonium bromide (CTAB) showed that up to 90% recovery can be achieved under optimum conditions, i.e., pH 11 with NaOH 0.2 mol L-1. In the case of the cells' suspension from the fermentation broth, three different approaches were investigated: (a) the conventional integrated approach where CGA were applied directly; (b) CGA were applied to the clarified suspension of cells; and finally (c) the in situ approach, where CGA are generated within the clarified suspension of cells. Interestingly, in the case of the whole suspension (approach a) highest recoveries (78%) were achieved under the same conditions found to be optimal for the standard solutions. In addition, up to 97% recovery of total carotenoids could be achieved from the clarified suspension after pretreatment with NaOH. This pretreatment led to maximum cell disruption as well as optimum conditioning for subsequent CGA separation. CONCLUSIONS: These results demonstrate the potential of CGA for the recovery of bioactive components from complex feedstock. (c) 2008 Society of Chemical Industry.

Effects of genotype and environment on free amino acid levels in wheat grain: implications for acrylamide formation during processing

Acrylamide forms from free asparagine and reducing sugars during cooking, with asparagine concentration being the key parameter determining the formation in foods produced from wheat flour. In this study free amino acid concentrations were measured in the grain of varieties Spark and Rialto and four doubled haploid lines from a Spark x Rialto mapping population. The parental and doubled haploid lines had differing levels of total free amino acids and free asparagine in the grain, with one line consistently being lower than either parent for both of these factors. Sulfur deprivation led to huge increases in the concentrations of free asparagine and glutamine, and canonical variate analysis showed clear separation of the grain samples as a result of treatment (environment, E) and genotype (G) and provided evidence of G x E interactions. Low grain sulfur and high free asparagine concentration were closely associated with increased risk of acrylamide formation. G, E, and G x E effects were also evident in grain from six varieties of wheat grown at field locations around the United Kingdom in 2006 and 2007. The data indicate that progress in reducing the risk of acrylamide formation in processed wheat products could be made immediately through the selection and cultivation of low grain asparagme varieties and that further genetically driven improvements should be achievable. However, genotypes that are selected should also be tested under a range of environmental conditions.

Effects of active information processing on the understanding of risk information

Two experiments investigated effects of active processing of risk information on participants' understanding and judgments. It was hypothesized that more active processing would lead to better understanding and differences in affective judgments (e.g. increased satisfaction and reduced perceived risk to health). In both experiments participants were given a written scenario about their being prescribed a fictitious medication. This medication was said to cause side effects in 2% of people who took it. Before answering a series of written questions, participants in the active conditions of both experiments were asked to carry out a reflective task (portraying the size of risk on a bar chart in Experiment 1 and answering a reflective question in Experiment 2). The results showed that active participants rated the likelihood of experiencing possible side effects significantly lower than passive participants (Experiment 1), and that active participants were significantly more satisfied with the information and judged perceived risk to health from taking the medication significantly lower than passive participants (Experiment 2). In both experiments, active participants were significantly more correct in their probability and frequency estimates. The studies demonstrate that active processing of risk information leads to improved understanding of the information given. This has important implications for risk communication. In the context of health, better understanding should lead to improved decision-making and health outcomes. Copyright (C) 2004 John Wiley Sons, Ltd.

Performance comparison of the optimal and the zero-forcing beamforming algorithms under practical conditions

The optimal and the zero-forcing beamformers are two commonly used algorithms in the subspace-based blind beamforming technology. The optimal beamformer is regarded as the algorithm with the best output SINR. The zero-forcing algorithm emphasizes the co-channel interference cancellation. This paper compares the performance of these two algorithms under some practical conditions: the effect of the finite data length and the existence of the angle estimation error. The investigation reveals that the zero-forcing algorithm can be more robust in the practical environment than the optimal algorithm.

Prefrontal inhibition of threat processing reduces working memory interference

Bottom-up processes can interrupt ongoing cognitive processing in order to adaptively respond to emotional stimuli of high potential significance, such as those that threaten wellbeing. However it is vital that this interference can be modulated in certain contexts to focus on current tasks. Deficits in the ability to maintain the appropriate balance between cognitive and emotional demands can severely impact on day-to-day activities. This fMRI study examined this interaction between threat processing and cognition; 18 adult participants performed a visuospatial working memory (WM) task with two load conditions, in the presence and absence of anxiety induction by threat of electric shock. Threat of shock interfered with performance in the low cognitive load condition; however interference was eradicated under high load, consistent with engagement of emotion regulation mechanisms. Under low load the amygdala showed significant activation to threat of shock that was modulated by high cognitive load. A directed top-down control contrast identified two regions associated with top-down control; ventrolateral PFC and dorsal ACC. Dynamic causal modeling provided further evidence that under high cognitive load, top-down inhibition is exerted on the amygdala and its outputs to prefrontal regions. Additionally, we hypothesized that individual differences in a separate, non-emotional top-down control task would predict the recruitment of dorsal ACC and ventrolateral PFC during top-down control of threat. Consistent with this, performance on a separate dichotic listening task predicted dorsal ACC and ventrolateral PFC activation during high WM load under threat of shock, though activation in these regions did not directly correlate with WM performance. Together, the findings suggest that under high cognitive load and threat, top-down control is exerted by dACC and vlPFC to inhibit threat processing, thus enabling WM performance without threat-related interference.