A thermally stable tension meter for atmospheric soundings using kites

Kites offer considerable potential as wind speed sensors—a role distinct from their traditional use as instrument-carrying platforms. In the sensor role, wind speed is measured by kite-line tension. A kite tether line tension meter is described here, using strain gauges mounted on an aluminum ring in a Wheatstone bridge electronic circuit. It exhibits a linear response to tension 19.5 mV N−1 with good thermal stability mean drift of −0.18 N °C−1 over 5–45 °C temperature range and a rapid time response 0.2 s or better. Field comparisons of tether line tension for a Rokkaku kite with a fixed tower sonic anemometer show an approximately linear tension-wind speed relationship over the range 1–6 ms−1. © 2010 American Institute of Physics. doi:10.1063/1.3465560

Architectural effect on the surface tension of an ABA triblock copolymer melt

The excess surface energy of lamellae formed by an ABA triblock copolymer melt oriented parallel to a neutral surface is evaluated using self-consistent field theory (SCFT). Consistent with experiments and previous SCFT calculations, we find a preference for the A-rich domains at the surface, which can only be attributed to the architectural asymmetry between the A and B blocks. The behavior was previously attributed to a loss of bridging configurations that occurs when the B-domain resides at the surface. Here we demonstrate that it is actually the presence of chain ends that reduces the excess surface energy of an A-rich domain relative that of a B-rich domain.

The significance of "nonsignificance" in randomized controlled studies: a discussion inspired by a double-blinded study on St. John's Wort (Hypericum perforatum L.) for premenstrual symptoms

Objectives: This study aimed to investigate the efficacy of St. John's wort extract (SJW) as a treatment for premenstrual symptoms. Design: The study was a randomized, double-blinded, placebo-controlled trial, with two parallel treatment groups. After a no-treatment baseline cycle, volunteers were randomized to either SJW or placebo for a further two menstrual cycles. Settings/location: A postal trial conducted from The University of Reading, Berkshire, England. Subjects: One hundred and sixty-nine (169) normally menstruating women who experienced recurrent premenstrual symptoms were recruited onto the study. One hundred and twenty-five (125) completed the protocol and were included in the analysis. Interventions: Six hundred milligrams (600) mg of SJW (standardized to contain 1800 mug of hypericin) or placebo (containing lactose and cellulose). Outcome measure: A menstrual diary was used to assess changes in premenstrual symptoms. The anxiety-related subgroup of symptoms of this instrument was used as the primary outcome measure. Results: After averaging the effects of treatment over both treatment cycles it was found that there was a trend for SJW to be superior to placebo. However, this finding was not statistically significant. Conclusion: The possibility that this nonsignificant finding resulted from insufficient statistical power in the study, rather than a lack of efficacy of SJW, is discussed. Following this discussion the recommendation is made that, in future, similar studies should be powered to detect a minimum clinically relevant difference between treatments.

Comparison of mechanical properties of tension and opposite wood in Populus

In this paper we focused on the differences of mechanical properties of tension and normal wood of 1-year-old poplar trees, artificially tilted. Elastic and fracture properties have been measured and linked to the anatomy. Tension wood is well known because it prevents good surface finishing and leads to difficulties with sawing. We studied three main mechanical properties: young modulus, energy of cutting and longitudinal residual strain of maturation (with strain gauges) because of their importance in wood technology. Moreover, this work takes place in a larger project of study, the phenomena of axes re-orientation in trees (allowing by the production of reaction wood), where these data are required for biomechanical modelling. The results show that tension wood has a higher young modulus, needs a higher energy to be cut and exhibited a higher level of longitudinal residual strain of maturation than those of normal wood. The results suggest that these differences require deeper analysis of the wood than anatomy: measurement of microfibril orientation in the S2 layer and also the lignin composition in monomeric units.

Stress generation in the tension wood of poplar is based on the lateral swelling power of the G-layer

The mechanism of active stress generation in tension wood is still not fully understood. To characterize the functional interdependency between the G-layer and the secondary cell wall, nanostructural characterization and mechanical tests were performed on native tension wood tissues of poplar (Populus nigra x Populus deltoids) and on tissues in which the G-layer was removed by an enzymatic treatment. In addition to the well-known axial orientation of the cellulose fibrils in the G-layer, it was shown that the microfibril angle of the S2-layer was very large (about 36 degrees). The removal of the G-layer resulted in an axial extension and a tangential contraction of the tissues. The tensile stress-strain curves of native tension wood slices showed a jagged appearance after yield that could not be seen in the enzyme-treated samples. The behaviour of the native tissue was modelled by assuming that cells deform elastically up to a critical strain at which the G-layer slips, causing a drop in stress. The results suggest that tensile stresses in poplar are generated in the living plant by a lateral swelling of the G-layer which forces the surrounding secondary cell wall to contract in the axial direction.

The significance of "nonsignificance" in randomized controlled studies: a discussion inspired by a double-blinded study on St. John's Wort (Hypericum perforatum L.) for premenstrual symptoms

Objectives: This study aimed to investigate the efficacy of St. John's wort extract (SJW) as a treatment for premenstrual symptoms. Design: The study was a randomized, double-blinded, placebo-controlled trial, with two parallel treatment groups. After a no-treatment baseline cycle, volunteers were randomized to either SJW or placebo for a further two menstrual cycles. Settings/location: A postal trial conducted from The University of Reading, Berkshire, England. Subjects: One hundred and sixty-nine (169) normally menstruating women who experienced recurrent premenstrual symptoms were recruited onto the study. One hundred and twenty-five (125) completed the protocol and were included in the analysis. Interventions: Six hundred milligrams (600) mg of SJW (standardized to contain 1800 mug of hypericin) or placebo (containing lactose and cellulose). Outcome measure: A menstrual diary was used to assess changes in premenstrual symptoms. The anxiety-related subgroup of symptoms of this instrument was used as the primary outcome measure. Results: After averaging the effects of treatment over both treatment cycles it was found that there was a trend for SJW to be superior to placebo. However, this finding was not statistically significant. Conclusion: The possibility that this nonsignificant finding resulted from insufficient statistical power in the study, rather than a lack of efficacy of SJW, is discussed. Following this discussion the recommendation is made that, in future, similar studies should be powered to detect a minimum clinically relevant difference between treatments.

Flow-induced dynamic surface tension effects at nanoscale

The aim of this study is to investigate flow-induced dynamic surface tension effects, similar to the well-known Marangoni phenomena, but solely generated by the nanoscale topography of the substrates. The flow-induced surface tension effects are examined on the basis of a sharp interface theory. It is demonstrated how nanoscale objects placed at the boundary of the flow domain result in the generation of substantial surface forces acting on the bulk flow.

A hypoplastic model of skeletal muscle development displaying reduced foetal myoblast cell numbers, increased oxidative myofibres and improved specific tension capacity

The major component of skeletal muscle is the myofibre. Genetic intervention inducing over-enlargement of myofibres beyond a certain threshold through acellular growth causes a reduction in the specific tension generating capacity of the muscle. However the physiological parameters of a genetic model that harbours reduced skeletal muscle mass have yet to be analysed. Genetic deletion of Meox2 in mice leads to reduced limb muscle size and causes some patterning defects. The loss of Meox2 is not embryonically lethal and a small percentage of animals survive to adulthood making it an excellent model with which to investigate how skeletal muscle responds to reductions in mass. In this study we have performed a detailed analysis of both late foetal and adult muscle development in the absence of Meox2. In the adult, we show that the loss of Meox2 results in smaller limb muscles that harbour reduced numbers of myofibres. However, these fibres are enlarged. These myofibres display a molecular and metabolic fibre type switch towards a more oxidative phenotype that is induced through abnormalities in foetal fibre formation. In spite of these changes, the muscle from Meox2 mutant mice is able to generate increased levels of specific tension compared to that of the wild type.

Relaxation of surface tension in the free-surface boundary layers of simple Lennard-Jones liquids

In this paper we use molecular dynamics to answer a classical question: how does the surface tension on a liquid/gas interface appear? After defining surface tension from the first principles and performing several consistency checks, we perform a dynamic experiment with a single simple liquid nanodroplet. At time zero, we remove all molecules of the interfacial layer of molecules, creating a fresh bare interface with the bulk arrangement of molecules. After that the system evolves towards equilibrium, and the expected surface tension is re-established. We found that the system relaxation consists of three distinct stages. First, the mechanical balance is quickly re-established. During this process the notion of surface tension is meaningless. In the second stage, the surface tension equilibrates, and the density profile broadens to a value which we call “intrinsic” interfacial width. During the third stage, the density profile continues to broaden due to capillary wave excitations, which does not however affect the surface tension.We have observed this scenario for monatomic Lennard-Jones (LJ) liquid as well as for binary LJ mixtures at different temperatures, monitoring a wide range of physical observables.

Relaxation of surface tension in the liquid-solid interfaces of Lennard-Jones liquids

We have established the surface tension relaxation time in the liquid-solid interfaces of Lennard-Jones (LJ) liquids by means of direct measurements in molecular dynamics (MD) simulations. The main result is that the relaxation time is found to be almost independent of the molecular structures and viscosity of the liquids (at seventy-fold change) used in our study and lies in such a range that in slow hydrodynamic motion the interfaces are expected to be at equilibrium. The implications of our results for the modelling of dynamic wetting processes and interpretation of dynamic contact angle data are discussed.