Anisotropic films of polypyrrole formed electrochemically using a non-planar dopant

We report the electrochemical preparation of electrically conducting films based on polypyrrole, using 10-camphorsulfonate as the dopant, which exhibit a highly anisotropic molecular organisation. This contrasts with earlier reports, in which anisotropy appeared to be restricted to films prepared using aromatic-based planar dopants. Possible growth mechanisms for these materials to account for the molecular anisotropy are discussed.

The effect of dopant molecules on the molecular order of electrically-conducting films of polypyrrole

X-ray scattering curves have been measured for a range of electrochemically-prepared conducting polypyrrole films employing a variety of counterions in aqueous solutions. Films containing counterions based on aromatic rings exhibit an anisotropic molecular organization. The degree of anisotropy is enhanced through the use of highly planar counterions. The electrical conductivity of such films is also improved if the charge/volume ratio of the counterion is maintained at a high level. Polypyrrole films prepared using ‘spherically’ shaped counterions such as SO42− do not display such anisotropic molecular organizations, and exhibit lower electrical conductivities. The competing structural roles of the counterions within these molecular composites are discussed.

Defining Structure in Electrospun Polymer Fibres

We use a combination of microscopy, x-ray scattering and neutron scattering to show how structure develops in micro and nano-size polymer fibres prepared by electrospinning. The technique has been applied to a range of different polymers, an amorphous system (polystyrene), a crystallisable polymer (poly-epsilon-caprolactone), a composite systems (polyethylene oxide or poly vinyl alcohol containing polypyrrole) and consider the possibility of self assembly (gelatin).

Conducting nanofibres produced by electrospinning

Electrospun fibres based on polypyrrole have been prepared. The incorporation of preformed polypyrrole into fibres electrospun from a carrier polymer can only be achieved when materials are prepared with particulates smaller than the cross-section of the fibre; even so there are some problems, with the substantial loss of material from the electrode tip. As an alternative approach, soluble polypyrroles can be prepared but these are not of sufficient viscosity to prepare electrospun fibres, once again a carrier polymer must be employed. More effective loadings are gained by the process of coating the outer surface of a pre-spun fibre; in this way electrospun fibres coated with polypyrrole can be prepared. This approach has been adapted to produce silver coated polymer fibres by the use of copolymers of styrene and 3-vinyl benzaldehyde.

The synthesis of novel 3-substituted polypyrroles bearing crown-ether moieties and a study of their electrochemical properties

A series of fourteen novel pyrrole monomers substituted at the 3-position with aliphatic and aromatic crown-ether moieties have been synthesised in good yield and characterised extensively. Several of these compounds were electropolymerised successfully in acetonitrile, using both potentiostatic and galvanostatic modes and the electrochemical properties of those systems were studied via cyclic voltammetry in aqueous and organic media. Novel crown-ether substituted polypyrrole derivatives revealed reversible redox couples in LiClO4/CH3CN (0.1 M). The morphology of these novel crown-ether substituted polypyrrole derivatives was characterised by scanning electron microscopy. These polymers exhibited an open porous structure and half the charge was required when compared to polypyrrole to afford films of equal thickness. The mass change during polymerisation was followed by electrochemical quartz crystal microbalance measurement, and the rate of polymer growth was found to be nonlinear when compared to polypyrrole. (c) 2005 Elsevier B.V. All rights reserved.

Structure property relationships in electrically conducting copolymers formed from pyrrole and N-methyl pyrrole

A series of copolymers containing differing proportions of pyrrole and N-methyl pyrrole were prepared electrochemically at various temperatures using acetonitrile as the solvent. The resultant electrical conductivity decreases universally with increasing fraction of N-methyl pyrrole. Films prepared with p-toluene sulfonate as the dopant show a marked variation in structural anisotropy as revealed by X-ray scattering with apparent copolymer content. There is a clear trend between the variation in electrical conductivity and this structural anisotropy. Different patterns of behaviour are observed for films prepared using perchlorate as the dopant and this is attributed to the role of the dopant and final structure in determining the relative reactivities of the pyrrole and N-methyl pyrrole monomers. These observations support the concept that the introduction of methyl substituents into a polypyrrole chain results in a twisted chain conformation. The structure and properties of the resultant copolymer films are particularly sensitive to the preparation conditions.

Influence of synthesis on the structure of electrochemically prepared electrically conducting polymers

The inherent possibility of structural anisotropy in polypyrrole and other heterocyclic systems is introduced. By selecting the appropriate electrochemical variables including monomer and dopant type this intrinsic molecular anisotropy may be used to prepare films with well defined global anisotropy, in which the planes of the pyrrole rings prefer to lie parallel to the electrode surface. The conditions for obtaining such materials are discussed and some of the effects of these novel anisotropic structures on the resultant properties are highlighted. Attention is directed at charge transport and optical properties.