A reconfigurable neural environment on active networks

This paper proposes the deployment of a neural network computing environment on Active Networks. Active Networks are packet-switched computer networks in which packets can contain code fragments that are executed on the intermediate nodes. This feature allows the injection of small pieces of codes to deal with computer network problems directly into the network core, and the adoption of new computing techniques to solve networking problems. The goal of our project is the adoption of a distributed neural network for approaching tasks which are specific of the computer network environment. Dynamically reconfigurable neural networks are spread on an experimental wide area backbone of active nodes (ABone) to show the feasibility of the proposed approach.

Active networks: an evolution of the internet

Active Networks can be seen as an evolution of the classical model of packet-switched networks. The traditional and ”passive” network model is based on a static definition of the network node behaviour. Active Networks propose an “active” model where the intermediate nodes (switches and routers) can load and execute user code contained in the data units (packets). Active Networks are a programmable network model, where bandwidth and computation are both considered shared network resources. This approach opens up new interesting research fields. This paper gives a short introduction of Active Networks, discusses the advantages they introduce and presents the research advances in this field.

Performance analysis of data transmissions in MPLS and non-MPLS networks

Basic Network transactions specifies that datagram from source to destination is routed through numerous routers and paths depending on the available free and uncongested paths which results in the transmission route being too long, thus incurring greater delay, jitter, congestion and reduced throughput. One of the major problems of packet switched networks is the cell delay variation or jitter. This cell delay variation is due to the queuing delay depending on the applied loading conditions. The effect of delay, jitter accumulation due to the number of nodes along transmission routes and dropped packets adds further complexity to multimedia traffic because there is no guarantee that each traffic stream will be delivered according to its own jitter constraints therefore there is the need to analyze the effects of jitter. IP routers enable a single path for the transmission of all packets. On the other hand, Multi-Protocol Label Switching (MPLS) allows separation of packet forwarding and routing characteristics to enable packets to use the appropriate routes and also optimize and control the behavior of transmission paths. Thus correcting some of the shortfalls associated with IP routing. Therefore MPLS has been utilized in the analysis for effective transmission through the various networks. This paper analyzes the effect of delay, congestion, interference, jitter and packet loss in the transmission of signals from source to destination. In effect the impact of link failures, repair paths in the various physical topologies namely bus, star, mesh and hybrid topologies are all analyzed based on standard network conditions.

A Packet/Frame sync detector based on statistical mode with application to wireless-USB

Wireless Personal Area Networks (WPANs) are offering high data rates suitable for interconnecting high bandwidth personal consumer devices (Wireless HD streaming, Wireless-USB and Bluetooth EDR). ECMA-368 is the Physical (PHY) and Media Access Control (MAC) backbone of many of these wireless devices. WPAN devices tend to operate in an ad-hoc based network and therefore it is important to successfully latch onto the network and become part of one of the available piconets. This paper presents a new algorithm for detecting the Packet/Fame Sync (PFS) signal in ECMA-368 to identify piconets and aid symbol timing. The algorithm is based on correlating the received PFS symbols with the expected locally stored symbols over the 24 or 12 PFS symbols, but selecting the likely TFC based on the highest statistical mode from the 24 or 12 best correlation results. The results are very favorable showing an improvement margin in the order of 11.5dB in reference sensitivity tests between the required performance using this algorithm and the performance of comparable systems.

A block coprocessor for user data rate improvements to GPRS coding scheme 4

The general packet radio service (GPRS) has been developed to allow packet data to be transported efficiently over an existing circuit-switched radio network, such as GSM. The main application of GPRS are in transporting Internet protocol (IP) datagrams from web servers (for telemetry or for mobile Internet browsers). Four GPRS baseband coding schemes are defined to offer a trade-off in requested data rates versus propagation channel conditions. However, data rates in the order of > 100 kbits/s are only achievable if the simplest coding scheme is used (CS-4) which offers little error detection and correction (EDC) (requiring excellent SNR) and the receiver hardware is capable of full duplex which is not currently available in the consumer market. A simple EDC scheme to improve the GPRS block error rate (BLER) performance is presented, particularly for CS-4, however gains in other coding schemes are seen. For every GPRS radio block that is corrected by the EDC scheme, the block does not need to be retransmitted releasing bandwidth in the channel and improving the user's application data rate. As GPRS requires intensive processing in the baseband, a viable field programmable gate array (FPGA) solution is presented in this paper.

Improving CS-4 user data rate in GPRS enabled devices by using a BLER co-processor

The General Packet Radio Service (GPRS) was developed to allow packet data to be transported efficiently over an existing circuit switched radio network. The main applications for GPRS are in transporting IP datagram’s from the user’s mobile Internet browser to and from the Internet, or in telemetry equipment. A simple Error Detection and Correction (EDC) scheme to improve the GPRS Block Error Rate (BLER) performance is presented, particularly for coding scheme 4 (CS-4), however gains in other coding schemes are seen. For every GPRS radio block that is corrected by the EDC scheme, the block does not need to be retransmitted releasing bandwidth in the channel, improving throughput and the user’s application data rate. As GPRS requires intensive processing in the baseband, a viable hardware solution for a GPRS BLER co-processor is discussed that has been currently implemented in a Field Programmable Gate Array (FPGA) and presented in this paper.

Performance analysis and deployment of VoLTE mechanisms over 3GPP LTE-based networks

Long Term Evolution based networks lack native support for Circuit Switched (CS) services. The Evolved Packet System (EPS) which includes the Evolved UMTS Terrestrial Radio Access Network (E-UTRAN) and Evolved Packet Core (EPC) is a purely all-IP packet system. This introduces the problem of how to provide voice call support when a user is within an LTE network and how to ensure voice service continuity when the user moves out of LTE coverage area. Different technologies have been proposed for the purpose of providing a voice to LTE users and to ensure the service continues outside LTE networks. The aim of this paper is to analyze and evaluate the overall performance of these technologies along with Single Radio Voice Call Continuity (SRVCC) Inter-RAT handover to Universal Terrestrial Radio Access Networks/ GSM-EDGE radio access Networks (UTRAN/GERAN). The possible solutions for providing voice call and service continuity over LTE-based networks are Circuit Switched Fall Back (CSFB), Voice over LTE via Generic Access (VoLGA), Voice over LTE (VoLTE) based on IMS/MMTel with SRVCC and Over The Top (OTT) services like Skype. This paper focuses mainly on the 3GPP standard solutions to implement voice over LTE. The paper compares various aspects of these solutions and suggests a possible roadmap that mobile operators can adopt to provide seamless voice over LTE.

Optimized hash for network path encoding with minimized false positives

The Bloom filter is a space efficient randomized data structure for representing a set and supporting membership queries. Bloom filters intrinsically allow false positives. However, the space savings they offer outweigh the disadvantage if the false positive rates are kept sufficiently low. Inspired by the recent application of the Bloom filter in a novel multicast forwarding fabric, this paper proposes a variant of the Bloom filter, the optihash. The optihash introduces an optimization for the false positive rate at the stage of Bloom filter formation using the same amount of space at the cost of slightly more processing than the classic Bloom filter. Often Bloom filters are used in situations where a fixed amount of space is a primary constraint. We present the optihash as a good alternative to Bloom filters since the amount of space is the same and the improvements in false positives can justify the additional processing. Specifically, we show via simulations and numerical analysis that using the optihash the false positives occurrences can be reduced and controlled at a cost of small additional processing. The simulations are carried out for in-packet forwarding. In this framework, the Bloom filter is used as a compact link/route identifier and it is placed in the packet header to encode the route. At each node, the Bloom filter is queried for membership in order to make forwarding decisions. A false positive in the forwarding decision is translated into packets forwarded along an unintended outgoing link. By using the optihash, false positives can be reduced. The optimization processing is carried out in an entity termed the Topology Manger which is part of the control plane of the multicast forwarding fabric. This processing is only carried out on a per-session basis, not for every packet. The aim of this paper is to present the optihash and evaluate its false positive performances via simulations in order to measure the influence of different parameters on the false positive rate. The false positive rate for the optihash is then compared with the false positive probability of the classic Bloom filter.