Fabrication and characterization of micromachined rectangular waveguide components for use at millimeter-wave and terahertz frequencies

The fabrication and characterization of micromachined reduced-height air-filled rectangular waveguide components suitable for integration is reported in this paper. The lithographic technique used permits structures with heights of up to 100 μm to be successfully constructed in a repeatable manner. Waveguide S-parameter measurements at frequencies between 75-110 GHz using a vector network analyzer demonstrate low loss propagation in the TE10 mode reaching 0.2 dB per wavelength. Scanning electron microscope photographs of conventional and micromachined waveguides show that the fabrication technique can provide a superior surface finish than possible with commercially available components. In order to circumvent problems in efficiently coupling free-space propagating beams to the reduced-height G-band waveguides, as well as to characterize them using quasi-optical techniques, a novel integrated micromachined slotted horn antenna has been designed and fabricated, E-, H-, and D-plane far-field antenna pattern measurements at different frequencies using a quasi-optical setup show that the fabricated structures are optimized for 180-GHz operation with an E-plane half-power beamwidth of 32° elevated 35° above the substrate, a symmetrical H-plane pattern with a half-power beamwidth of 23° and a maximum D-plane cross-polar level of -33 dB. Far-field pattern simulations using HFSS show good agreement with experimental results.

Millimeter-wave measurements of the complex dielectric constant of an advanced thick film UV photoresist

The first measurement of the relative permittivity (εr) and loss tangent (tan δ) of EPON™ SU-8 advanced thick film ultraviolet photoresist is reported at frequencies between 75–110 GHz (W-band). The problems associated with such a measurement are discussed, an error analysis given, and values of εr=1.725±0.08 and tanδ =0.02±0.001 are determined.

A new micro-machined millimeter-wave and terahertz snap-together rectangular waveguide technology

A novel technique for micro-machining millimeter and submillimeter-wave rectangular waveguide components is reported. These are fabricated in two halves which simply snap together, utilizing locating pins and holes, and are physically robust, and cheap, and easy to manufacture. In addition, S-parameter measurements on these structures are reported for the first time and display lower loss than previously reported micro-machined rectangular waveguides.

Earthworms produce granules of intricately zoned calcite

Earthworms of the family Lumbricidae, which includes many common species, produce and secrete up to millimeter-sized calcite granules, and the intricate fine-scale zoning of their constituent crystals is unique for a biomineral. Granule calcite is produced by crystallization of amorphous calcium carbonate (ACC) that initially precipitates within the earthworm calciferous glands, then forms protogranules by accretion on quartz grain cores. Crystallization of ACC is mediated by migrating fluid films and is largely complete within 24 11 of ACC production and before granules leave the earthworm. Variations in the density of defects formed as a byproduct of trace element incorporation during calcite crystall growth have generated zoning that can be resolved by cathodoluminescence imaging at ultraviolet to blue wavelengths and using the novel technique of scanning electron microscope charge contrast imaging. Mapping of calcite crystal orientations by electron backscatter diffraction reveals an approximate radial fabric to the granules that reflects crystal growth from internal nucleation sites toward their margins. The survival within granules of ACC inclusions for months after they enter soils indicates that they crystallize only within the earthworm and in the presence of fluids containing biochemical catalysts. The earthworm probably promotes crystallization of ACC in order to prevent remobilization of the calcium carbonate by dissolution. Calcite granules vividly illustrate the role of transient precursors in biomineralization, but the underlying question of why earth-worms produce granules in volumes sufficient to have a measurable impact on soil carbon cycling remains to be answered.

The harmonic force field and rz structure of HNCO

The presently available microwave, millimeter wave, and far-infrared data of five isotopic species of isocyanic acid, namely, HNCO, H15NCO, HN13CO, HNC18O, and DNCO, have been used to obtain improved values of the ground-state rotational constants, the five quartic distortion constants, and some higher-order distortion constants in the Ir S reduced Hamiltonian of Watson. The appropriate planarity relation among the quartic centrifugal distortion constants has been imposed in the fitting procedure. The general harmonic force field of isocyanic acid has been determined using all existing data, and assuming a trans bent equilibrium geometry of the molecule with an NCO angle of 170°. Finally an rz structure has been obtained using the Az, Bz, and Cz rotational constants of five isotopic species. The bending of the NCO chain is found to be 8° in the trans configuration.

Sample-induced beam distortions in terahertz time domain spectroscopy and imaging systems

It is demonstrated that distortion of the terahertz beam profile and generation of a cross-polarised component occur when the beam in terahertz time domain spectroscopy and imaging systems interacts with the sample under test. These distortions modify the detected signal, leading to spectral and image artefacts. The degree of distortion depends on the optical design of the system as well as the properties of the sample.

The consequences of diffractively spreading beams in ultrafast THz spectroscopy

There are established methods for calculating optical constants from measurements using a broadband terahertz (THz) source. Applications to ultrafast THz spectroscopy have adopted the key assumption that the THz beam is treated as a normal incidence plane-wave. We show that this assumption results in a frequency-dependent systematic error, which is compounded by distortion of the beam on introduction of the sample.

Pulse shaping using state space algorithms

We discuss the use of pulse shaping for optimal excitation of samples in time-domain THz spectroscopy. Pulse shaping can be performed in a 4f optical system to specifications from state space models of the system's dynamics. Subspace algorithms may be used for the identification of the state space models.

State-space model identification of a wireless THz network

We model the large scale fading of wireless THz communications links deployed in a metropolitan area taking into account reception through direct line of sight, ground or wall reflection and diffraction. The movement of the receiver in the three dimensions is modelled by an autonomous dynamic linear system in state-space whereas the geometric relations involved in the attenuation and multi-path propagation of the electric field are described by a static non-linear mapping. A subspace algorithm in conjunction with polynomial regression is used to identify a Wiener model from time-domain measurements of the field intensity.

Quantification of boundary definition using pulsed terahertz radiation for wedged geometries

The interaction of a terahertz beam with a sample containing a material boundary across the profile of the terahertz beam produces characteristic spectroscopic detail. A full vectorial model is presented to quantify boundary definition for a series of wedged geometries. As a result of this work, using simple geometric forms, we wish to be able to extend these ideas to characterize boundaries in more irregular samples, impacting most application areas of pulsed terahertz radiation.

Towards a THz osmometer

This work discusses the use of a THz-transient spectrometer for the measurement of tissue water content. The relation of both mammalian- and plant-cell water content to the osmotic potential is discussed. The process of equilibration of tissue water potential with the water potential of water vapor in an osmometer cuvette is described. Observation of the THz transmittance through the water vapor provides a measure of the water activity and water potential in the sample. The possibility of performing dielectric relaxation measurements of the liquid water in the tissue at THz frequencies directly and the use of proline as marker of water stress in tissue are discussed.

Subspace and wavelet-packet algorithms for de-noising and classifying broadband THz transients

The results from a range of different signal processing schemes used for the further processing of THz transients are contrasted. The performance of different classifiers after adopting these schemes are also discussed.