The atomic structure of low-index surfaces of the intermetallic compound InPd

The intermetallic compound InPd (CsCl type of crystal structure with a broad compositional range) is considered as a candidate catalyst for the steam reforming of methanol. Single crystals of this phase have been grown to study the structure of its three low-index surfaces under ultra-high vacuum conditions, using low energy electron diffraction (LEED), X-ray photoemission spectroscopy (XPS), and scanning tunneling microscopy (STM). During surface preparation, preferential sputtering leads to a depletion of In within the top few layers for all three surfaces. The near-surface regions remain slightly Pd-rich until annealing to ∼580 K. A transition occurs between 580 and 660 K where In segregates towards the surface and the near-surface regions become slightly In-rich above ∼660 K. This transition is accompanied by a sharpening of LEED patterns and formation of flat step-terrace morphology, as observed by STM. Several superstructures have been identified for the different surfaces associated with this process. Annealing to higher temperatures (≥750 K) leads to faceting via thermal etching as shown for the (110) surface, with a bulk In composition close to the In-rich limit of the existence domain of the cubic phase. The Pd-rich InPd(111) is found to be consistent with a Pd-terminated bulk truncation model as shown by dynamical LEED analysis while, after annealing at higher temperature, the In-rich InPd(111) is consistent with an In-terminated bulk truncation, in agreement with density functional theory (DFT) calculations of the relative surface energies. More complex surface structures are observed for the (100) surface. Additionally, individual grains of a polycrystalline sample are characterized by micro-spot XPS and LEED as well as low-energy electron microscopy. Results from both individual grains and “global” measurements are interpreted based on comparison to our single crystals findings, DFT calculations and previous literature.

Quantification of the probability of containment failure caused by an in-vessel steam explosion for the Sizewell B PWR

AEA Technology has provided an assessment of the probability of α-mode containment failure for the Sizewell B PWR. After a preliminary review of the methodologies available it was decided to use the probabilistic approach described in the paper, based on an extension of the methodology developed by Theofanous et al. (Nucl. Sci. Eng. 97 (1987) 259–325). The input to the assessment is 12 probability distributions; the bases for the quantification of these distributions are discussed. The α-mode assessment performed for the Sizewell B PWR has demonstrated the practicality of the event-tree method with input data represented by probability distributions. The assessment itself has drawn attention to a number of topics, which may be plant and sequence dependent, and has indicated the importance of melt relocation scenarios. The α-mode failure probability following an accident that leads to core melt relocation to the lower head for the Sizewell B PWR has been assessed as a few parts in 10 000, on the basis of current information. This assessment has been the first to consider elevated pressures (6 MPa and 15 MPa) besides atmospheric pressure, but the results suggest only a modest sensitivity to system pressure.

Cannabinoid influences on palatability: microstructural analysis of sucrose drinking after Delta(9)-tetrahydrocannabinol, anandamide, 2-arachidonoyl glycerol and SR141716

Rationale: Central cannabinoid systems have been implicated in appetite control through the respective hyperphagic and anorectic actions of CB1 agonists and antagonists. The motivational changes underlying these actions remain to be determined, but may involve alterations to food palatability. Objectives: The mode of action of cannabinoids on ingestion was investigated by examining the effects of exogenous and endogenous agonists, and a selective CB1 receptor antagonist, on licking microstructure in rats ingesting a palatable sucrose solution. Methods: Microstructural analyses of licking for a 10% sucrose solution was performed over a range of agonist and antagonist doses administered to non-deprived, male Lister hooded rats. Results: Delta(9)-tetrahydrocannabinol (0.5, 1 and 3 mg/kg) and anandamide (1 mg/kg and 3 mg/kg) significantly increased total number of licks. This was primarily due to an increase in bout duration rather than bout number. There was a nonsignificant increase in total licks following administration of 2-arachidonoyl glycerol (0.2, 1.0 and 2.0 mg/kg), whereas administration of the CB1 antagonist SR141716 (1 mg/kg and 3 mg/kg) significantly decreased total licks. All drugs, with the exception of anandamide, significantly decreased the intra-bout lick rate. An exponential function fitted to the cumulative lick rate curves for each drug revealed that all compounds altered the asymptote of this function without having any marked effects on the exponent. Conclusions: These data are consistent with endocannabinoid involvement in the mediation of food palatability.

Multiple PID mapping using neural networks in a MIMO steam generator system

A neural network was used to map three PID operating regions for a two-input two-output steam generator system. The network was used in stand alone feedforward operation to control the whole operating range of the process, after being trained from the PID controllers corresponding to each control region. The network inputs are the plant error signals, their integral, their derivative and a 4-error delay train.

Reforming the CDM for sustainable development: lessons learned and policy futures

The Clean Development Mechanism (CDM) has successfully demonstrated that market-based mechanisms can achieve some cost effective emissions reductions in developing countries. However the distribution of CDM projects has been extremely uneven across countries and regions, and a few technologies and sectors have dominated the early stages of CDM experience. This has caused some to question whether the CDM has fallen short of its potential in contributing to sustainable development. We review the broad patterns of CDM project approvals and evaluate 10 CDM projects according to their sustainability benefits. The difficulty of defining “sustainable development” and the process of defining criteria by individual non-Annex 1 governments has meant that sustainable development concerns have been marginalized in some countries. Given these observed limitations, we present possible CDM policy futures, focusing on the main proposals for a post-2012 climate regime. Five options for enhancing the sustainable development benefits in the CDM are discussed, including proactive approaches to favour eligibility of emission reduction projects which ensure such co-benefits.

Rheology of milk foams produced by steam injection

Rheology of milk foams generated by steam injection was studied during the transient destabilization process using steady flow and dynamic oscillatory techniques: yield stress (τ_y) values were obtained from a stress ramp (0.2 to 25 Pa) and from strain amplitude sweep (0.001 to 3 at 1 Hz of frequency); elastic (G') and viscous (G") moduli were measured by frequency sweep (0.1 to 150 Hz at 0.05 of strain); and the apparent viscosity (η_a) was obtained from the flow curves generated from the stress ramp. The effect of plate roughness and the sweep time on τ_y was also assessed. Yield stress was found to increase with plate roughness whereas it decreased with the sweep time. The values of yield stress and moduli—G' and G"—increased during foam destabilization as a consequence of the changes in foam properties, especially the gas volume fraction, φ, and bubble size, R_32 (Sauter mean bubble radius). Thus, a relationship between τ_y, φ, R_32, and σ (surface tension) was established. The changes in the apparent viscosity, η, showed that the foams behaved like a shear thinning fluid beyond the yield point, fitting the modified Cross model with the relaxation time parameter (λ) also depending on the gas volume fraction. Overall, it was concluded that the viscoelastic behavior of the foam below the yield point and liquid-like behavior thereafter both vary during destabilization due to changes in the foam characteristics.

Proteomic analyses of a Listeria monocytogenes mutant lacking σB identify new components of the σB regulon and highlight a role for σB in the utilization of glycerol

In Listeria monocytogenes the alternative sigma factor σB plays important roles in both virulence and stress tolerance. In this study a proteomic approach was used to define components of the σB regulon in L. monocytogenes 10403S (serotype 1/2a). Using two-dimensional gel electrophoresis and the recently developed isobaric tags for relative and absolute quantitation technique, the protein expression profiles of the wild type and an isogenic ΔsigB deletion strain were compared. Overall, this study identified 38 proteins whose expression was σB dependent; 17 of these proteins were found to require the presence of σB for full expression, while 21 were expressed at a higher level in the ΔsigB mutant background. The data obtained with the two proteomic approaches showed limited overlap (four proteins were identified by both methods), a finding that highlights the complementarity of the two technologies. Overall, the proteomic data reaffirmed a role for σB in the general stress response and highlighted a probable role for σB in metabolism, especially in the utilization of alternative carbon sources. Proteomic and physiological data revealed the involvement of σB in glycerol metabolism. Five newly identified members of the σB regulon were shown to be under direct regulation of σB using reverse transcription-PCR (RT-PCR), while random amplification of cDNA ends-PCR was used to map four σB-dependent promoters upstream from lmo0796, lmo1830, lmo2391, and lmo2695. Using RT-PCR analysis of known and newly identified σB-dependent genes, as well as proteomic analyses, σB was shown to play a major role in the stationary phase of growth in complex media.

Reforming the House of Lords: difficult but not impossible

Despite apparent cross-party and public support, Nick Clegg’s plan to reform the House of Lords is dead. This article asks what explains its demise and analyses whether comprehensive Lords reform is ever likely to get off the ground in the future.

Apartment ownership: the English version needs reforming

In this contribution, the English commonhold system, which enables the development of freehold units in a multi-unit development, is critically re-visited. Provision is made for the development of freehold apartments on land with a registered commonhold title. At the date of registration, a management body for the scheme, the commonhold association, must be in place. Each purchaser of a unit in the relevant building obtains freehold property on purchase. The property and management of the building housing the units and of the common areas of the scheme are, by contrast, withheld from unit holders and vested in the commonhold association, which is a special kind of body corporate. Since the coming into force of the English legislation, a set of defects have been detected. This contribution re-assesses the main problem areas and makes a number of reform suggestions drawing on material from a number of jurisdictions, notably South Africa, France and Germany. Avoidable problems are likely to arise with any conversions to commonhold from the predominant English long lease system, owing to the narrowness of the conversion rules. The manner in which ownership of units and the common parts are regulated, a key aspect in any such system, merits re-assessment. It seems that here the English rules survive comparison. The rules pertaining to constitution of the commonhold association fail to provide sufficient safeguards for unpaid scheme creditors. The rules relating leasing of commonhold units seem inadequately thought out. There is a conspicuous absence of real remedies for non-payment of assessments by unit holders. The effect of these and other aspects may help to explain why commonhold has had a limited numerical impact. The time for a second generation reforming statute may have come.

Enhanced MALDI MS sensitivity by weak base additives and glycerol sample coating

The concept of rationally designing MALDI matrices has been extended to the next “whole sample” level. These studies have revealed some unexpected and exploitable insights in improving MALDI sensitivity. It is shown that (i) additives which only provide additional laser energy absorption are best to be avoided; (ii) the addition of proton donors in the form of protonated weak bases can be highly beneficial; (iii) the addition of glycerol for coating crystalline samples is highly recommended. Overall, analytical sensitivity has been significantly increased compared to the current “gold” standards in MALDI MS, and new insights into the mechanisms and processes of MALDI have been gained.

Glycerol prevents dehydration in lipid cubic phases

Lipid cubic phase samples dry out and undergo phase transitions when exposed to air. We demonstrate experimentally and theoretically that adding glycerol controllably lowers the humidity at which cubic phases form. These results broaden the potential applications of cubic phases and open up the potential of a new humidityresponsive nanomaterial.

Production of milk foams by steam injection: the effects of steam pressure and nozzle design

Foam properties depend on the physico-chemical characteristics of the continuous phase, the method of production and process conditions employed; however the preparation of barista-style milk foams in coffee shops by injection of steam uses milk as its main ingredient which limits the control of foam properties by changing the biochemical characteristics of the continuous phase. Therefore, the control of process conditions and nozzle design are the only ways available to produce foams with diverse properties. Milk foams were produced employing different steam pressures (100-280 kPa gauge) and nozzle designs (ejector, plunging-jet and confined-jet nozzles). The foamability of milk, and the stability, bubble size and texture of the foams were investigated. Variations in steam pressure and nozzle design changed the hydrodynamic conditions during foam production, resulting in foams having a range of properties. Steam pressure influenced foam characteristics, although the net effect depended on the nozzle design used. These results suggest that, in addition to the physicochemical determinants of milk, the foam properties can also be controlled by changing the steam pressure and nozzle design.

Reforming theatre in Farnese Parma: the case of the Accademia degli Innominati (1574-1608)

The essay explores the socio-cultural role of the main academy in Parma, the Innominati (1574-1608), which flourished in the years when the Farnese dynasty was beginning to assert more forcefully its political control over the new state of Parma and Piacenza. The Innominati was from the start associated with the ruling dynasty, who must have recognized the importance of its cultural activities to strengthening their regime, particularly in the absence of a strong local university. This essay explores the institution’s contested position within the cultural landscape – as reflected also in its membership of courtiers, clergymen, and feudal aristocrats with more ambivalent relations with the Farnese. In particular, the focus falls on the theatrical activities of the group during the 1580s, a decade which saw the establishment of the Parma Index (1580) and the succession of the internationally celebrated Duke Alessandro Farnese (1587). Based on the little surviving evidence it is argued that the Academy in the 1580s became a creative hub for theatrical experimentation – through theoretical debate and composition, and possibly even performance. However, as relations between the Farnese and the local elites, especially feudal aristocrats, became more contested the Academy’s theatrical production and the public memory of this became increasingly controlled.

Effect of impurities in biodiesel-derived waste glycerol on the performance and feasibility of biotechnological processes

The rapid development of biodiesel production technology has led to the generation of tremendous quantities of glycerol wastes, as the main by-product of the process. Stoichiometrically, it has been calculated that for every 100 kg of biodiesel, 10 kg of glycerol are produced. Based on the technology imposed by various biodiesel plants, glycerol wastes may contain numerous kinds of impurities such as methanol, salts, soaps, heavy metals and residual fatty acids. This fact often renders biodiesel-derived glycerol unprofitable for further purification. Therefore, the utilization of crude glycerol though biotechnological means represents a promising alternative for the effective management of this industrial waste. This review summarizes the effect of various impurities-contaminants that are found in biodiesel-derived crude glycerol upon its conversion by microbial strains in biotechnological processes. Insights are given concerning the technologies that are currently applied in biodiesel production, with emphasis to the impurities that are added in the composition of crude glycerol, through each step of the production process. Moreover, extensive discussion is made in relation with the impact of the nature of impurities upon the performances of prokaryotic and eukaryotic microorganisms, during crude glycerol bioconversions into a variety of high added-value metabolic products. Finally, aspects concerning ways of crude glycerol treatment for the removal of inhibitory contaminants as reported in the literature are given and comprehensively discussed