Cutting, by 'pressing and slicing,' of thin floppy slices of materials illustrated by experiments on cheddar cheese and salami

Why it is easier to cut with even the sharpest knife when 'pressing down and sliding' than when merely 'pressing down alone' is explained. A variety of cases of cutting where the blade and workpiece have different relative motions is analysed and it is shown that the greater the 'slice/push ratio' xi given by ( blade speed parallel to the cutting edge/blade speed perpendicular to the cutting edge), the lower the cutting forces. However, friction limits the reductions attainable at the highest.. The analysis is applied to the geometry of a wheel cutting device (delicatessan slicer) and experiments with a cheddar cheese and a salami using such an instrumented device confirm the general predictions. (C) 2004 Kluwer Academic Publishers.

A study of the microstructure and condition of thin sheets of painting support ivory using SEM and ESEM

This paper outlines a study of the microstructure of thin sheets of ivory used as a painting support for portrait miniatures. Warping of the ivory support is one of the main problems commonly found in portrait miniatures from the late eighteenth century and early nineteenth century. Portrait miniatures from this period are painted on very thin sheets of ivory that are often only 0.2 mm in thickness. Warping can lead to cracking of the ivory and can also accentuate flaking of the paint layer. The problem of warping in ivory has thus been of long-term interest to conservators who deal with portrait miniatures, including those at the Victoria and Albert (V&A) Museum. The causes of warping are complex. However, it should be noted that artists normally stuck the thin ivory sheets onto paper or card before commencing the painting. The possible causes of warping therefore are thought to relate to the differential reactions of the ivory/adhesive/paper or card layers to changes in relative humidity (RH). It is well known that ivory is hygroscopic and anisotropic.1 However, only a few scientific studies have been carried out related to this subject and systematic analyses of the morphological and microstructural changes due to changes in RH or moisture in such thin sheets of ivory have yet to be investigated.

Synthesis, structural analysis, and magnetic behaviour of three fumarate bridged coordination polymers: five-fold interpenetrated diamond-like net of Ni-II, sheets of Ni-II and Co-II

The hydrothermal reactions of Ni(NO3)(2).6H(2)O, disodium fumarate (fum) and 1,2-bis(4-pyridyl)ethane (bpe)/1,3-bis(4-pyridyl) propane (bpp) in aqueous-methanol medium yield one 3-D and one 2-D metal-organic hybrid material, [Ni(fum)(bpe)] (1) and [Ni(fum)(bpp)(H2O)] (2), respectively. Complex 1 possesses a novel unprecedented structure, the first example of an "unusual mode" of a five-fold distorted interpenetrated network with metal-ligand linkages where the four six-membered windows in each adamantane-type cage are different. The structural characterization of complex 2 evidences a buckled sheet where nickel ions are in a distorted octahedral geometry, with two carboxylic groups, one acting as a bis-chelate, the other as a bis-monodentate ligand. The metal ion completes the coordination sphere through one water molecule and two bpp nitrogens in cis position. Variable-temperature magnetic measurements of complexes 1 and 2 reveal the existence of very weak antiferromagnetic intramolecular interactions and/or the presence of single-ion zero field splitting (D) of isolated Ni-II ions in both the compounds. Experimentally, both the J parameters are close, comparable and very small. Considering zero-field splitting of Ni-II, the calculated D values are in agreement with values reported in the literature for Ni-II ions. Complex 3, [{Co(phen)}(2)(fum)(2)] (phen=1,10-phenanthroline) is obtained by diffusing methanolic solution of 1,10-phenanthroline on an aqueous layer of disodium fumarate and Co(NO3)(2).6H(2)O. It consists of dimeric Co-II(phen) units, doubly bridged by carboxylate groups in a distorted syn-syn fashion. These fumarate anions act as bis-chelates to form corrugated sheets. The 2D layer has a (4,4) topology, with the nodes represented by the centres of the dimers. The magnetic data were fitted ignoring the very weak coupling through the fumarate pathway and using a dimer model.

Mode I fracture of sheet metal

The perceived wisdom about thin sheet fracture is that (i) the crack propagates under mixed mode I & III giving rise to a slant through-thickness fracture profile and (ii) the fracture toughness remains constant at low thickness and eventually decreases with increasing thickness. In the present study, fracture tests performed on thin DENT plates of various thicknesses made of stainless steel, mild steel, 6082-O and NS4 aluminium alloys, brass, bronze, lead, and zinc systematically exhibit (i) mode I “bath-tub”, i.e. “cup & cup”, fracture profiles with limited shear lips and significant localized necking (more than 50% thickness reduction), (ii) a fracture toughness that linearly increases with increasing thickness (in the range of 0.5–5 mm). The different contributions to the work expended during fracture of these materials are separated based on dimensional considerations. The paper emphasises the two parts of the work spent in the fracture process zone: the necking work and the “fracture” work. Experiments show that, as expected, the work of necking per unit area linearly increases with thickness. For a typical thickness of 1 mm, both fracture and necking contributions have the same order of magnitude in most of the metals investigated. A model is developed in order to independently evaluate the work of necking, which successfully predicts the experimental values. Furthermore, it enables the fracture energy to be derived from tests performed with only one specimen thickness. In a second modelling step, the work of fracture is computed using an enhanced void growth model valid in the quasi plane stress regime. The fracture energy varies linearly with the yield stress and void spacing and is a strong function of the hardening exponent and initial void volume fraction. The coupling of the two models allows the relative contributions of necking versus fracture to be quantified with respect to (i) the two length scales involved in this problem, i.e. the void spacing and the plate thickness, and (ii) the flow properties of the material. Each term can dominate depending on the properties of the material which explains the different behaviours reported in the literature about thin plate fracture toughness and its dependence with thickness.

Evidence of heavy metal movement down the profile of a heavily-sludged soil

Two sites in central England where sewage sludge has been deposited for decades were studied to measure the heavy metal distribution in the soil profiles. The first site (S 1) was a field receiving heavy loads sludge from a nearby wastewater treatment plant, and the second (S2) was a farm applying 'normal' sludge rates of 8 t ha(-1) y(-1) of the same sludge. Soil samples were also taken by a near-by untreated control site. In S I the movement of heavy metals was significant even down to 80 cm depth compared to the control. In S2, the concentrations of lead (Pb) and zinc (Zn) and the organic matter content were higher than the control down to 20 cm, while nickel (Ni) moved significantly down to 80 cm. This underlies. the possibility that the metals bound onto organic surfaces moved along with organic matter down to that depth. The movement of metals in S2 points out the potential risks of applying sewage sludge for a long time.

Characterization and identification of mixed-metal phosphates in soils: the application, of Raman spectroscopy

The development of protocols for the identification of metal phosphates in phosphate-treated, metal-contaminated soils is a necessary yet problematical step in the validation of remediation schemes involving immobilization of metals as phosphate phases. The potential for Raman spectroscopy to be applied to the identification of these phosphates in soils has yet to be fully explored. With this in mind, a range of synthetic mixed-metal hydroxylapatites has been characterized and added to soils at known concentrations for analysis using both bulk X-ray powder diffraction (XRD) and Raman spectroscopy. Mixed-metal hydroxylapatites in the binary series Ca-Cd, Ca-Pb, Ca-Sr and Cd-Pb synthesized in the presence of acetate and carbonate ions, were characterized using a range of analytical techniques including XRD, analytical scanning electron microscopy (SEM), infrared spectroscopy (IR), inductively coupled plasma-atomic emission spectrometry (ICP-AES) and Raman spectroscopy. Only the Ca-Cd series displays complete solid solution, although under the synthesis conditions of this study the Cd-5(PO4)(3)OH end member could not be synthesized as a pure phase. Within the Ca-Cd series the cell parameters, IR active modes and Raman active bands vary linearly as a function of Cd content. X-ray diffraction and extended X-ray absorption fine structure spectroscopy (EXAFS) suggest that the Cd is distributed across both the Ca(1) and Ca(2) sites, even at low Cd concentrations. In order to explore the likely detection limits for mixed-metal phosphates in soils for XRD and Raman spectroscopy, soils doped with mixed-metal hydroxylapatites at concentrations of 5, 1 and 0.5 wt.% were then studied. X-ray diffraction could not confirm unambiguously the presence or identity of mixed-metal phosphates in soils at concentrations below 5 wt.%. Raman spectroscopy proved a far more sensitive method for the identification of mixed-metal hydroxylapatites in soils, which could positively identify the presence of such phases in soils at all the dopant concentrations used in this study. Moreover, Raman spectroscopy could also provide an accurate assessment of the degree of chemical substitution in the hydroxylapatites even when present in soils at concentrations as low as 0.1%.

LDA or GGA? A combined experimental inelastic neutron scattering and ab initio lattice dynamics study of alkali metal hydrides

In a previous work, we carried out inelastic neutron scattering (INS) spectroscopy experiments and preliminary first principles calculations on alkali metal hydrides. The complete series of alkali metal hydrides, LiH, NaH, KH, RbH and CsH was measured in the high-resolution TOSCA INS spectrometer at ISIS. Here, we present the results of ab initio electronic structure calculations of the properties of the alkali metal hydrides using both the local density approximation (LDA) and the generalized gradient approximation (GGA), using the Perdew–Burke–Ernzerhof (PBE) parameterization. Properties calculated were lattice parameters, bulk moduli, dielectric constants, effective charges, electronic densities and inelastic neutron scattering (INS) spectra. We took advantage of the currently available computer power to use full lattice dynamics theory to calculate thermodynamic properties for these materials. For the alkali metal hydrides (LiH, NaH, KH, RbH and CsH) using lattice dynamics, we found that the INS spectra calculated using LDA agreed better with the experimental data than the spectra calculated using GGA. Both zero-point effects and thermal contributions to free energies had an important effect on INS and several thermodynamic properties.

Comparison of white metal and resin socket terminations for wire ropes

Previously the authors have presented both theoretical and experimental work discussing the operating mechanism of a wire rope held in a tapered socket by means of a cast resin cone. The work reported here extends the investigation to address the question of whether the same socket fabricated with white metal operates in the same manner. To date, previous investigations have compared the operational efficiency of resin and white metal in terms of both strength and/or fatigue endurance. Some other work has analysed the operation of resin sockets or specific cast metal terminations. This paper seeks to draw the results from this work together, and, in addition to a theoretical analysis, presents experimental data obtained from a direct comparison of the operation mechanism for the same sockets filled with resin or white metal. Results show that white metal terminations have a very different distribution of stresses along the length of the socket basket from resin terminations, and a smaller but still significant amount of socket draw. For both types of termination the socket draw develops high frictional gripping forces which can transfer the load from the rope to the socket. The different stress distributions mean that the consequences of termination fabrication defects may not be the same for resin and white metal terminations.

Surface structure of thin asymmetric PS-b-PMMA diblock copolymers investigated by atomic force microscopy

Asymmetric poly(styrene-b-methyl methacrylate) (PS-b-PMMA) diblock copolymers of molecular weight M-n = 29,700g mol(-1) (M-PS = 9300 g mol(-1) M-PMMA = 20,100 g mol(-1), PD = 1.15, chi(PS) = 0.323, chi(PMMA) = 0.677) and M-n = 63,900 g mol(-1) (M-PS = 50,500 g mol(-1), M-PMMA = 13,400 g mol(-1), PD = 1.18, chi(PS) = 0.790, chi(PMMA) = 0.210) were prepared via reversible addition-fragmentation chain transfer (RAFT) polymerization. Atomic force microscopy (AFM) was used to investigate the surface structure of thin films, prepared by spin-coating the diblock copolymers on a silicon substrate. We show that the nanostructure of the diblock copolymer depends on the molecular weight and volume fraction of the diblock copolymers. We observed a perpendicular lamellar structure for the high molar mass sample and a hexagonal-packed cylindrical patterning for the lower molar mass one. Small-angle X-ray scattering investigation of these samples without annealing did not reveal any ordered structure. Annealing of PS-b-PMMA samples at 160 degrees C for 24 h led to a change in surface structure.

Surface science studies of strong metal-oxide interactions on model catalysts

The strong metal support interaction (SMSI) was first described in 1978 by Tauster [1-4]. The effect was observed as a severely negative effect on CO and H2 uptake on the catalyst after high temperature calcination under reducing conditions (heating above ~ 700 K) [1,2]. It also had a negative effect on the reaction rate for reactions, such as alkane hydrogenolysis [5,6]. It appeared that the effect occurred for catalysts comprised of reducible supports which were treated at elevated temperature in reducing conditions [2-4]. A classic support which has manifested this behaviour in many studies is TiO2. Over the years following the first discovery of SMSI it has been recognised that the effect is not always negative – for instance for the CO-H2 reaction for which it appears to have a positive effect [5,6]. Further it was noted that hydrogen reduction was not necessary to observe the effect of CO adsorption suppression, it also occurs by vacuum treatment [7], though it should be noted that vacuum treatment at elevated temperature is, in effect, a reducing environment.

Preparation of transition metal complexes of bicyclo[2.2.1]hept-5-ene-2-carboxylic acid (C7H9CO2H) and X-ray crystal structure of [Cu2?(±)-endo-μ-O2CC7H9?4 (CH3OH)2]·2CH3OH

Metathesis reactions were used to prepare a range of dicopper(II), monocopper(I), diruthenium(II, III), dimolybdenum(II,II) and dirhodium(II,II) complexes of either racemic or resolved forms of endo- and exo-bicyclo[2.2.1]hept-5-ene-2-carboxylic acid (C7H9CO2H). The X-ray crystal structure of [Cu2{(±)-endo-μ-O2CC7H9}4(CH3OH)2]·2CH3OH shows the two copper(II) ions bridged by two (+)-endo-bicyclo[2.2.1]hept-5-ene-2-carboxylate anions and two (−)-endo-bicyclo[2.2.1]hept-5-ene-2-carboxylate anions. Methanol molecules occupy the two trans axial sites, and there are also two methanol molecules hydrogen bonded to opposite carboxyl oxygens.

Abundance and diversity of wild bees along gradients of heavy metal pollution

1. Wild bees are one of the most important groups of pollinators in the temperate zone. Therefore, population declines have potentially negative impacts for both crop and wildflower pollination. Although heavy metal pollution is recognized to be a problem affecting large parts of the European Union, we currently lack insights into the effects of heavy metals on wild bees. 2. We investigated whether heavy metal pollution is a potential threat to wild bee communities by comparing (i) species number, (ii) diversity and (iii) abundance as well as (iv) natural mortality of emerging bees along two independent gradients of heavy metal pollution, one at Olkusz (OLK), Poland and the other at Avonmouth (AVO), UK. We used standardized nesting traps to measure species richness and abundance of wild bees, and we recorded the heavy metal concentration in pollen collected by the red mason bee Osmia rufa as a measure of pollution. 3. The concentration of cadmium, lead and zinc in pollen collected by bees ranged from a background level in unpolluted sites [OLK: 1·3, 43·4, 99·8 (mg kg−1); AVO: 0·8, 42·0, 56·0 (mg kg−1), respectively] to a high level on sites in the vicinity of the OLK and AVO smelters [OLK: 6·7, 277·0, 440·1 (mg kg−1); AVO: 9·3, 356·2, 592·4 (mg kg−1), respectively]. 4. We found that with increasing heavy metal concentration, there was a steady decrease in the number, diversity and abundance of solitary, wild bees. In the most polluted sites, traps were empty or contained single occupants, whereas in unpolluted sites, the nesting traps collected from 4 to 5 species represented by up to ten individuals. Moreover, the proportion of dead individuals of the solitary bee Megachile ligniseca increased along the heavy metal pollution gradient at OLK from 0·2 in uncontaminated sites to 0·5 in sites with a high concentration of pollution. 5. Synthesis and applications. Our findings highlight the negative relationship between heavy metal pollution and populations of wild bees and suggest that increasing wild bee richness in highly contaminated areas will require special conservation strategies. These may include creating suitable nesting sites and sowing a mixture of flowering plants as well as installing artificial nests with wild bee cocoons in polluted areas. Applying protection plans to wild pollinating bee communities in heavy metal-contaminated areas will contribute to integrated land rehabilitation to minimize the impact of pollution on the environment.

Producing leisure spaces out of thin air: the case of the Countryside Stewardship Scheme

This paper examines the growing dysfunction between the apparently increasing significance of diverse leisure practices in the countryside and the largely unchanging official response towards them. Although there is recognition in the recent rural White Paper (DOE and MAFF, 1995) that access is essential to enjoying the countryside, the construction of this term is dubious, since paid access agreements, based on producer requirements, are favoured over any form of demand-driven freedom to roam. Using the Countryside Stewardship Scheme (CSS) as an example of the incentive structure developed to promote this policy, the paper applies Plato's simulacrum as a reading of how this process is being utilised to underpin the dominant rights associated with rural property interests. In particular, the paper makes the point that rather than representing the corollary of a market situation, as its supporters claim, the CSS involves government grant for the eclectic provision of short term licences over ground which remains unmapped as anything other than its continued agricultural use. In concluding, the paper asserts that rather than representing an increase in the availability of leisure sites in the countryside, the CSS and other schemes represent a diversion from the wider and deeper socio-cultural process of continued wealth and power redistribution.

Metalloporphyrin anion sensors: the effect of the metal centre on the anion binding properties of amide-functionalised and tetraphenyl metalloporphyrins

This article describes the synthesis and anion binding properties of a series of ‘picket fence’ metalloporphyrin complexes, within which the metal centre is systematically varied. The porphyrin structure contains four amide bonds and is the same for each metal. The anion binding properties of these receptors are further contrasted with those of their tetraphenylporphyrin congeners to elucidate both the effect of the metal centre and the influence of the amide groups on the anion recognition process. Anion binding was demonstrated using UV/visible and 1H NMR spectroscopies, electrochemistry and luminescence. The metal centre was found to be highly influential in the strength and selectivity of binding; for example, the cadmium and mercury complexes exhibited far greater affinities for anions than the zinc complexes in competitive solvents such as DMSO. The amide functionalities were found to enhance the anion binding process.