Evaluation of two hybrid metric-conceptual models, for simulating phosphorus transfer from agricultural land in the river enborne, a lowland UK catchment

Across Europe, elevated phosphorus (P) concentrations in lowland rivers have made them particularly susceptible to eutrophication. This is compounded in southern and central UK by increasing pressures on water resources, which may be further enhanced by the potential effects of climate change. The EU Water Framework Directive requires an integrated approach to water resources management at the catchment scale and highlights the need for modelling tools that can distinguish relative contributions from multiple nutrient sources and are consistent with the information content of the available data. Two such models are introduced and evaluated within a stochastic framework using daily flow and total phosphorus concentrations recorded in a clay catchment typical of many areas of the lowland UK. Both models disaggregate empirical annual load estimates, derived from land use data, as a function of surface/near surface runoff, generated using a simple conceptual rainfall-runoff model. Estimates of the daily load from agricultural land, together with those from baseflow and point sources, feed into an in-stream routing algorithm. The first model assumes constant concentrations in runoff via surface/near surface pathways and incorporates an additional P store in the river-bed sediments, depleted above a critical discharge, to explicitly simulate resuspension. The second model, which is simpler, simulates P concentrations as a function of surface/near surface runoff, thus emphasising the influence of non-point source loads during flow peaks and mixing of baseflow and point sources during low flows. The temporal consistency of parameter estimates and thus the suitability of each approach is assessed dynamically following a new approach based on Monte-Carlo analysis. (c) 2004 Elsevier B.V. All rights reserved.

Can climate models capture the structure of extratropical cyclones?

Composites of wind speeds, equivalent potential temperature, mean sea level pressure, vertical velocity, and relative humidity have been produced for the 100 most intense extratropical cyclones in the Northern Hemisphere winter for the 40-yr ECMWF Re-Analysis (ERA-40) and the high resolution global environment model (HiGEM). Features of conceptual models of cyclone structure—the warm conveyor belt, cold conveyor belt, and dry intrusion—have been identified in the composites from ERA-40 and compared to HiGEM. Such features can be identified in the composite fields despite the smoothing that occurs in the compositing process. The surface features and the three-dimensional structure of the cyclones in HiGEM compare very well with those from ERA-40. The warm conveyor belt is identified in the temperature and wind fields as a mass of warm air undergoing moist isentropic uplift and is very similar in ERA-40 and HiGEM. The rate of ascent is lower in HiGEM, associated with a shallower slope of the moist isentropes in the warm sector. There are also differences in the relative humidity fields in the warm conveyor belt. In ERA-40, the high values of relative humidity are strongly associated with the moist isentropic uplift, whereas in HiGEM these are not so strongly associated. The cold conveyor belt is identified as rearward flowing air that undercuts the warm conveyor belt and produces a low-level jet, and is very similar in HiGEM and ERA-40. The dry intrusion is identified in the 500-hPa vertical velocity and relative humidity. The structure of the dry intrusion compares well between HiGEM and ERA-40 but the descent is weaker in HiGEM because of weaker along-isentrope flow behind the composite cyclone. HiGEM’s ability to represent the key features of extratropical cyclone structure can give confidence in future predictions from this model.

Pollination and other ecosystem services produced by mobile organisms: a conceptual framework for the effects of land-use change

Many ecosystem services are delivered by organisms that depend on habitats that are segregated spatially or temporally from the location where services are provided. Management of mobile organisms contributing to ecosystem services requires consideration not only of the local scale where services are delivered, but also the distribution of resources at the landscape scale, and the foraging ranges and dispersal movements of the mobile agents. We develop a conceptual model for exploring how one such mobile-agent-based ecosystem service (MABES), pollination, is affected by land-use change, and then generalize the model to other MABES. The model includes interactions and feedbacks among policies affecting land use, market forces and the biology of the organisms involved. Animal-mediated pollination contributes to the production of goods of value to humans such as crops; it also bolsters reproduction of wild plants on which other services or service-providing organisms depend. About one-third of crop production depends on animal pollinators, while 60-90% of plant species require an animal pollinator. The sensitivity of mobile organisms to ecological factors that operate across spatial scales makes the services provided by a given community of mobile agents highly contextual. Services vary, depending on the spatial and temporal distribution of resources surrounding the site, and on biotic interactions occurring locally, such as competition among pollinators for resources, and among plants for pollinators. The value of the resulting goods or services may feed back via market-based forces to influence land-use policies, which in turn influence land management practices that alter local habitat conditions and landscape structure. Developing conceptual models for MABES aids in identifying knowledge gaps, determining research priorities, and targeting interventions that can be applied in an adaptive management context.

Behaviour models clarify definitions of affordance and capability

There is ongoing work on conceptual modelling of such busi- ness notions as Affordance and Capability. We have found that such business notions as Affordance and Capability are constructively defned using elements and properties of exe- cutable behaviour models. In this paper, we clarify the def- initions of Affordance and Capability using Coloured Petri Nets and Protocol models.The illustrating case is the process of drug injection. We show that different behaviour modelling techniques provide different precision for definition of Affordance and Capability and clarify the conceptual models of these notions. We generalise that the behaviour models can be used to improve the precision of conceptualization.

Modelling the inorganic nitrogen behaviour in a small Mediterranean forested catchment, Fuirosos (Catalonia)

The aim of this work was to couple a nitrogen (N) sub-model to already existent hydrological lumped (LU4-N) and semi-distributed (LU4-R-N and SD4-R-N) conceptual models, to improve our understanding of the factors and processes controlling nitrogen cycling and losses in Mediterranean catchments. The N model adopted provides a simplified conceptualization of the soil nitrogen cycle considering mineralization, nitrification, immobilization, denitrification, plant uptake, and ammonium adsorption/desorption. It also includes nitrification and denitrification in the shallow perched aquifer. We included a soil moisture threshold for all the considered soil biological processes. The results suggested that all the nitrogen processes were highly influenced by the rain episodes and that soil microbial processes occurred in pulses stimulated by soil moisture increasing after rain. Our simulation highlighted the riparian zone as a possible source of nitrate, especially after the summer drought period, but it can also act as an important sink of nitrate due to denitrification, in particular during the wettest period of the year. The riparian zone was a key element to simulate the catchment nitrate behaviour. The lumped LU4-N model (which does not include the riparian zone) could not be validated, while both the semi-distributed LU4-R-N and SD4-R-N model (which include the riparian zone) gave satisfactory results for the calibration process and acceptable results for the temporal validation process.

Context and aims of the Aqua-Planet Experiment

The Aqua-Planet Experiment (APE) was first proposed by Neale and Hoskins (2000a) as a benchmark for atmospheric general circulation models (AGCMs) on an idealised water-covered Earth. The experiment and its aims are summarised, and its context within a modelling hierarchy used to evaluate complex models and to provide a link between realistic simulation and conceptual models of atmospheric phenomena is discussed. The simplified aqua-planet configuration bridges a gap in the existing hierarchy. It is designed to expose differences between models and to focus attention on particular phenomena and their response to changes in the underlying distribution of sea surface temperature.

An extratropical cyclone database: A tool for illustrating cyclone structure and evolution characteristics

Extratropical cyclone lifecycles have been studied extensively with the aim of understanding the dynamical mechanisms involved in their development. Previous work has often been based on subjective analysis of individual case studies. Such case studies have contributed heavily to the generation of conceptual models of extratropical cyclones that provide a framework for understanding the dynamical evolution of cyclones. These conceptual models are widely used in educational meteorology courses throughout the world to illustrate the basic structure and evolution of extratropical cyclones. This article presents a database of extratropical cyclone composites which highlight the average structure and evolution of 20 years of extratropical cyclones, as opposed to individual case studies. The composite fields are achieved by combining a database containing cyclone tracks from the ERA-Interim reanalysis (1989-2009, 6 hourly) with the full 3D ERA-Interim reanalysis fields. Vertical and horizontal composites of cyclone structure for cyclones generated in the Atlantic and Pacific regions identifying features such as the relative positions of cold, warm and occluded fronts and their associated wind and cloud patterns are shown. In addition the evolution of cyclonic flows such as the warm and cold conveyor belts and dry intrusion are illustrated. A webpage containing an archive of the composited data is freely available for educational purposes.

The APE atlas

This Atlas presents statistical analyses of the simulations submitted to the Aqua-Planet Experiment (APE) data archive. The simulations are from global Atmospheric General Circulation Models (AGCM) applied to a water-covered earth. The AGCMs include ones actively used or being developed for numerical weather prediction or climate research. Some are mature, application models and others are more novel and thus less well tested in Earth-like applications. The experiment applies AGCMs with their complete parameterization package to an idealization of the planet Earth which has a greatly simplified lower boundary that consists of an ocean only. It has no land and its associated orography, and no sea ice. The ocean is represented by Sea Surface Temperatures (SST) which are specified everywhere with simple, idealized distributions. Thus in the hierarchy of tests available for AGCMs, APE falls between tests with simplified forcings such as those proposed by Held and Suarez (1994) and Boer and Denis (1997) and Earth-like simulations of the Atmospheric Modeling Intercomparison Project (AMIP, Gates et al., 1999). Blackburn and Hoskins (2013) summarize the APE and its aims. They discuss where the APE fits within a modeling hierarchy which has evolved to evaluate complete models and which provides a link between realistic simulation and conceptual models of atmospheric phenomena. The APE bridges a gap in the existing hierarchy. The goals of APE are to provide a benchmark of current model behaviors and to stimulate research to understand the cause of inter-model differences., APE is sponsored by the World Meteorological Organization (WMO) joint Commission on Atmospheric Science (CAS), World Climate Research Program (WCRP) Working Group on Numerical Experimentation (WGNE). Chapter 2 of this Atlas provides an overview of the specification of the eight APE experiments and of the data collected. Chapter 3 lists the participating models and includes brief descriptions of each. Chapters 4 through 7 present a wide variety of statistics from the 14 participating models for the eight different experiments. Additional intercomparison figures created by Dr. Yukiko Yamada in AGU group are available at http://www.gfd-dennou.org/library/ape/comparison/. This Atlas is intended to present and compare the statistics of the APE simulations but does not contain a discussion of interpretive analyses. Such analyses are left for journal papers such as those included in the Special Issue of the Journal of the Meteorological Society of Japan (2013, Vol. 91A) devoted to the APE. Two papers in that collection provide an overview of the simulations. One (Blackburn et al., 2013) concentrates on the CONTROL simulation and the other (Williamson et al., 2013) on the response to changes in the meridional SST profile. Additional papers provide more detailed analysis of the basic simulations, while others describe various sensitivities and applications. The APE experiment data base holds a wealth of data that is now publicly available from the APE web site: http://climate.ncas.ac.uk/ape/. We hope that this Atlas will stimulate future analyses and investigations to understand the large variation seen in the model behaviors.

Ecophysiological and bioclimatic foundations for a global plant functional classification

Question: What plant properties might define plant functional types (PFTs) for the analysis of global vegetation responses to climate change, and what aspects of the physical environment might be expected to predict the distributions of PFTs? Methods: We review principles to explain the distribution of key plant traits as a function of bioclimatic variables. We focus on those whole-plant and leaf traits that are commonly used to define biomes and PFTs in global maps and models. Results: Raunkiær's plant life forms (underlying most later classifications) describe different adaptive strategies for surviving low temperature or drought, while satisfying requirements for reproduction and growth. Simple conceptual models and published observations are used to quantify the adaptive significance of leaf size for temperature regulation, leaf consistency for maintaining transpiration under drought, and phenology for the optimization of annual carbon balance. A new compilation of experimental data supports the functional definition of tropical, warm-temperate, temperate and boreal phanerophytes based on mechanisms for withstanding low temperature extremes. Chilling requirements are less well quantified, but are a necessary adjunct to cold tolerance. Functional traits generally confer both advantages and restrictions; the existence of trade-offs contributes to the diversity of plants along bioclimatic gradients. Conclusions: Quantitative analysis of plant trait distributions against bioclimatic variables is becoming possible; this opens up new opportunities for PFT classification. A PFT classification based on bioclimatic responses will need to be enhanced by information on traits related to competition, successional dynamics and disturbance.

The four pillars of corporate responsibility: ethics, leadership, personal responsibility and trust

Purpose – This paper aims to examine how to further embed CSR thinking and practice into corporations, particularly in emerging markets, by reviewing and drawing similarities between key issues faced by all senior managers, namely ethics, leadership, personal responsibility and trust. Design/methodology/approach – This paper presents a conceptual exploration of global CSR practices using social psychology and overlays this concept with strategic and institutional theory in order to encourage new ways of thinking about CSR adoption, especially in emerging markets. Findings – The paper reveals the importance of shareholder needs on global corporate decision making and applies alternative conceptual models to help businesses to devise better CSR practices and individuals to align their actions to their own values. Originality/value – This paper strongly argues for blending different theoretical foundations from the management and organization literature in order to draw comparisons between current global CSR practice and the potential for its further adoption in emerging markets.

The implications of climate change for the water environment in England

This paper reviews the implications of climate change for the water environment and its management in England. There is a large literature, but most studies have looked at flow volumes or nutrients and none have considered explicitly the implications of climate change for the delivery of water management objectives. Studies have been undertaken in a small number of locations. Studies have used observations from the past to infer future changes, and have used numerical simulation models with climate change scenarios. The literature indicates that climate change poses risks to the delivery of water management objectives, but that these risks depend on local catchment and water body conditions. Climate change affects the status of water bodies, and it affects the effectiveness of measures to manage the water environment and meet policy objectives. The future impact of climate change on the water environment and its management is uncertain. Impacts are dependent on changes in the duration of dry spells and frequency of ‘flushing’ events, which are highly uncertain and not included in current climate scenarios. There is a good qualitative understanding of ways in which systems may change, but interactions between components of the water environment are poorly understood. Predictive models are only available for some components, and model parametric and structural uncertainty has not been evaluated. The impacts of climate change depend on other pressures on the water environment in a catchment, and also on the management interventions that are undertaken to achieve water management objectives. The paper has also developed a series of consistent conceptual models describing the implications of climate change for pressures on the water environment, based around the source-pathway-receptor concept. They provide a framework for a systematic assessment across catchments and pressures of the implications of climate change for the water environment and its management.

Rooting theories of plant community ecology in microbial interactions

Predominant frameworks for understanding plant ecology have an aboveground bias that neglects soil micro-organisms. This is inconsistent with recent work illustrating the importance of soil microbes in terrestrial ecology. Microbial effects have been incorporated into plant community dynamics using ideas of niche modification and plant–soil community feedbacks. Here, we expand and integrate qualitative conceptual models of plant niche and feedback to explore implications of microbial interactions for understanding plant community ecology. At the same time we review the empirical evidence for these processes. We also consider common mycorrhizal networks, and propose that these are best interpreted within the feedback framework. Finally, we apply our integrated model of niche and feedback to understanding plant coexistence, monodominance and invasion ecology.

Towards conceptualizing reverse service supply chains

Purpose – Recognizing the heterogeneity of services, this paper aims to clarify the characteristics of forward and the corresponding reverse supply chains of different services. Design/methodology/approach – The paper develops a two-dimensional typology matrix, representing four main clusters of services according to the degree of input standardization and the degree of output tangibility. Based on this matrix, this paper develops a typology and parsimonious conceptual models illustrating the characteristics of forward and the corresponding reverse supply chains of each cluster of services. Findings – The four main clusters of service supply chains have different characteristics. This provides the basis for the identification, presentation and explanation of the different characteristics of their corresponding reverse service supply chains. Research limitations/implications – The findings of this research can help future researchers to analyse, map and model forward and reverse service supply chains, and to identify potential research gaps in the area. Practical/implications – The findings of the research can help managers of service firms to gain better visibility of their forward and reverse supply chains, and refine their business models to help extend their reverse/closed-loop activities. Furthermore, the findings can help managers to better optimize their service operations to reduce service gaps and potentially secure new value-adding opportunities. Originality/value – This paper is the first, to the authors ' knowledge, to conceptualize the basic structure of the forward and reverse service supply chains while dealing with the high level of heterogeneity of services.

Advancing construction industry development, innovative research and new thinking

Academic writing has a tendency to be turgid and impenetrable. This is not only anathema to communication between academics, but also a major barrier to advancing construction industry development. Clarity in our communication is a prerequisite to effective collaboration with industry. An exploration of what it means to be an academic in a University is presented in order to provide a context for a discussion on how academics might collaborate with industry to advance development. There are conflicting agendas that pull the academic in different directions: peer group recognition, institutional success and industry development. None can be achieved without the other, which results in the need for a careful balancing act. While academics search for better understandings and provisional explanations within the context of conceptual models, industry seeks the practical application of new ideas, whether the ideas come from research or experience. Universities have a key role to play in industry development and in economic development.

Integration of chaos theory and mathematical models in building simulation: Part II: Conceptual frameworks

Current mathematical models in building research have been limited in most studies to linear dynamics systems. A literature review of past studies investigating chaos theory approaches in building simulation models suggests that as a basis chaos model is valid and can handle the increasing complexity of building systems that have dynamic interactions among all the distributed and hierarchical systems on the one hand, and the environment and occupants on the other. The review also identifies the paucity of literature and the need for a suitable methodology of linking chaos theory to mathematical models in building design and management studies. This study is broadly divided into two parts and presented in two companion papers. Part (I), published in the previous issue, reviews the current state of the chaos theory models as a starting point for establishing theories that can be effectively applied to building simulation models. Part (II) develop conceptual frameworks that approach current model methodologies from the theoretical perspective provided by chaos theory, with a focus on the key concepts and their potential to help to better understand the nonlinear dynamic nature of built environment systems. Case studies are also presented which demonstrate the potential usefulness of chaos theory driven models in a wide variety of leading areas of building research. This study distills the fundamental properties and the most relevant characteristics of chaos theory essential to (1) building simulation scientists and designers (2) initiating a dialogue between scientists and engineers, and (3) stimulating future research on a wide range of issues involved in designing and managing building environmental systems.