The consolidation and bond strength of rafted sea ice

The consolidation and bond strength of rafted sea ice were investigated through a series of experiments undertaken in the Ice Physics Laboratory at the UCL. To simulate a section of rafted sea ice, blocks of laboratory grown saline ice were stacked in an insulated tank with spacers between adjacent blocks to allow saline water to flood in. The rate of consolidation was then monitored using a combination of temperature readings recorded in the ice and liquid layer, salinity measurements of the liquid layer, and cores taken at specific times of interest. Two states of consolidation were observed: thermodynamic consolidation where the ice blocks were physically bonded but the bond strength was weak, and mechanical consolidation where the bond had reached full strength. Results showed that the rafted ice had physically bonded in less than a day, however it took many more days (6 to 30 depending on the environmental conditions) for the bond to reach maximum strength. Increasing the thickness of the ice, the salinity of the water and the inter-block gap size all increased the consolidation time. Once consolidated, ice cores were taken and sheared using the asymmetric four-point bending method to measure the strength of the bond between the ice blocks. These were then compared to the shear strength of solid ice blocks simulating level sea ice. Our results show that the shear strength of the bond between the rafted ice blocks is about 30% weaker than that of level ice.

Synergetic effects of the Cu/Pt{110} surface alloy: enhanced reactivity of water and carbon monoxide

We have used synchrotron-based high-resolution X-ray photoelectron spectroscopy in combination with ab initio density functional theory calculations to investigate the characteristics of water and CO adsorption on the bimetallic Cu/Pt{110}-(2 x 1) surface at a Cu coverage near 0.5 ML. Cu fills the troughs of the reconstructed clean surface forming nanowires, which are stable up to 830 K. Their presence dramatically influences the adsorption of water and CO. Water adsorption changes from intact to partially dissociated while the desorption temperature of CO on this surface increases by up to 27 K with respect to the clean Pt{110} surface. Ab initio calculations and experimental valence band spectra reveal that the Cu 3d-band is narrowed and shifted upward with respect to bulk Cu surfaces. This and electron donation to surface Pt atoms cause the increase in the bond strength between CO and the Pt surface atoms. The pathway for water dissociation occurs via Cu surface atoms. The heat of adsorption of water bonding to Cu surface atoms was calculated to be 0.82 eV, which is significantly higher than on the clean Pt{110} surface; the activation energy for partial dissociation is 0.53 eV (not corrected for zero point energy).

Time-resolved gas-phase kinetic and quantum chemical studies of the reaction of silylene with oxygen

Time-resolved kinetic studies of the reaction of silylene, SiH2, generated by laser flash photolysis of phenylsilane, have been carried out to obtain rate constants for its bimolecular reaction with O-2. The reaction was studied in the gas phase over the pressure range 1-100 Torr in SF6 bath gas, at five temperatures in the range 297-600 K. The second order rate constants at 10 Torr were fitted to the Arrhenius equation: log(k/cm(3) molecule(-1) s(-1)) = (-11.08 +/- 0.04) + (1.57 +/- 0.32 kJ mol(-1))/RT ln10 The decrease in rate constant values with increasing temperature, although systematic is very small. The rate constants showed slight increases in value with pressure at each temperature, but this was scarcely beyond experimental uncertainty. From estimates of Lennard-Jones collision rates, this reaction is occurring at ca. 1 in 20 collisions, almost independent of pressure and temperature. Ab initio calculations at the G3 level backed further by multi-configurational (MC) SCF calculations, augmented by second order perturbation theory (MRMP2), support a mechanism in which the initial adduct, H2SiOO, formed in the triplet state (T), undergoes intersystem crossing to the more stable singlet state (S) prior to further low energy isomerisation processes leading, via a sequence of steps, ultimately to dissociation products of which the lowest energy pair are H2O + SiO. The decomposition of the intermediate cyclo-siladioxirane, via O-O bond fission, plays an important role in the overall process. The bottleneck for the overall process appears to be the T -> S process in H2SiOO. This process has a small spin orbit coupling matrix element, consistent with an estimate of its rate constant of 1 x 10(9) s(-1) obtained with the aid of RRKM theory. This interpretation preserves the idea that, as in its reactions in general, SiH2 initially reacts at the encounter rate with O-2. The low values for the secondary reaction barriers on the potential energy surface account for the lack of an observed pressure dependence. Some comparisons are drawn with the reactions of CH2 + O-2 and SiCl2 + O-2.

Syntheses, conformations, and basicities of bicyclic triamines

The multistep syntheses of several bicyclic triamines are described, all of which have an imbedded 1,5,9-triazacyclododecane ring. In 1,5,9-triazabicyclo[7.3.3]pentadecanes 12, 13, 15, and 16, two nitrogens are bridged by three carbons. The monoprotonated forms of these triamines are highly stabilized by a hydrogen-bonded network involving the bridge and both bridgehead nitrogens, producing a difference of more than 8 pK(a) units in acidities of their monoprotonated and diprotonated forms. The one- and zero-carbon bridges in 1,5,9-triazabicyclo[9.1.1]tridecane (23) and 7-methyl-1,5,9-triazabicyclo[5.5.0]dodecane (39) do not enhance the stabilities of their monoprotonated forms. X-ray crystal structures and computational studies of 12.HI and 16.HI reveal similar, but somewhat weaker, hydrogen-bonded networks, relative to 15.HI. The activation free energies for conformational inversion of 13.HI (14.4 +/- 0.2 kcal/mol), 16.HI (15.0 +/- 0.1 kcal/mol) and 16 (8.8 +/- 0.3 kcal/mol) were measured by variable-temperature H-1 and C-13 NMR spectroscopy. These experimental barriers give an estimate of 6.2 kcal/mol for the strength of the bifurcated hydrogen bond between the bridge nitrogen and cavity proton in 16.HI. Computational studies support the hypothesis that N-inversion occurs in an open conformation, leading to an estimate of 10.32 kcal/mol for the enthalpy of the bifurcated hydrogen bond in 16.HI in the gas phase.

Chemical, physical and electrical properties of aged dodecylbenzene 2: thermal ageing of single isomers in air

The linear isomer of dodecylbenzene (DDB), 1-phenyldodecane, was aged at temperatures of 105 and 135 degrees C in air and the resultant products were analyzed using a range of analytical techniques. On ageing, the 1-phenyldodecane darkened, the acid number, dielectric loss and water content increased and significant oxidation peaks were detected in the infrared spectrum. When aged in the presence of copper, a characteristic peak at 680 nm was also detected by UV/visible spectroscopy but, compared with previous studies of a cable-grade DDB, the strength of this peak was much increased and no appreciable precipitate formation occurred. At the same time, very high values of dielectric loss were recorded. On ageing in the absence of copper, an unusually strong infrared carbonyl band was seen, which correlates well with the detection of dodecanophenone by gas chromatography / mass spectrometry and nuclear magnetic resonance spectroscopy. It was therefore concluded that the ageing process proceeds via the initial production of aromatic ketones, which may then be further oxidized to carboxylic acids. In the presence of copper, these oxidation products are present in lower quantities, most of these oxidation products being combined with the copper present in the oil to give copper carboxylates. The behavior is described in terms of a complex autoxidation mechanism, in which copper acts as both an oxidizing and a reducing agent, depending on its oxidation state and, in particular, promotes elimination via the oxidation of intermediate alkyl radical species to carbocations.

Tuning of intramolecular electron transfer between Ru(II) and the disulfide bond

Reaction of 2,2'-dithiodipyridine (DTDP) with cis-Ru(bpy)(2)Cl-2 (bpy = 2,2'-bipyridine) and cis-Ru(phen)(2)Cl-2 (phen = 1,10-phenanthroline) respectively yields the dicationic species [Ru(bpy) (2)(DTDP)](2+) and [Ru(phen)(2) (DTDP)](2+) in which the S-S bond of DTDP remains intact. The S-S bond undergoes a reductive cleavage when DTDP is reacted with cis-Ru(bisox)(2)Cl-2 (bisox = 4,4,4',4'-tetramethyl-2,2'-bisoxazoline) under identical conditions to generate the monocationic species [Ru(bisox)(2)(2-thiolatopyridine)]. The intramolecular electron transfer between the metal and the S-S bond is found to be subtly controlled by the crystal field strength of the ancillary bidentate N-donor ligands.

Anion-templated assembly of pseudorotaxanes: importance of anion template, strength of ion-pair thread association, and macrocycle ring size

A wide range of pseuclorotaxane assemblies containing positively charged pyridinium, pyridinium nicotinamide, imidazolium, benzimidazolium and guanidinium threading components, and macrocyclic isophthalamide polyether ligands have been prepared using a general anion templation procedure. In noncompetitive solvent media, coupling halide anion recognition by a macrocyclic ligand with ion-pairing between the halide anion and a strongly associated cation provides the driving force for interpenetration. Extensive solution H-1 NMR binding studies, thermodynamic investigations, and single-crystal X-ray structure determinations reveal that the nature of the halide anion template, strength of the ion-pairing between the anion template and the cationic threading component, and to a lesser extent favorable second sphere pi-pi aromatic stacking interactions between the positively charged threading component and macrocyclic ligand, together with macrocyclic ring size, affect the efficacy of pseudorotaxane formation.

Hydrogen bond-induced pair formation of glycine on the chiral Cu{531} surface

Enantio-specific interactions on intrinsically chiral or chirally modified surfaces can be identified experimentally via comparison of the adsorption geometries of similar nonchiral and chiral molecules. Information about the effects of substrate-related and in interactions on the adsorption geometry of glycine, the only natural nonchiral amino acid, is therefore important for identifying enantio-specific interactions of larger chiral amino acids. We have studied the long- and short-range adsorption geometry and bonding properties of glycine on the intrinsically chiral Cu{531} surface with low-energy electron diffraction, near-edge X-ray absorption One structure spectroscopy, X-ray photoelectron spectroscopy, and temperature-programmed desorption. For coverages between 0.15 and 0.33 ML (saturated chemisorbed layer) and temperatures between 300 and 430 K, glycine molecules adsorb in two different azimuthal orientations, which are associated with adsorption sites on the {110} and {311} microfacets of Cu{531}. Both types of adsorption sites allow a triangular footprint with surface bonds through the two oxygen atoms and the nitrogen atom. The occupation of the two adsorption sites is equal for all coverages, which can be explained by pair formation due to similar site-specific adsorption energies and the possibility of forming hydrogen bonds between molecules on adjacent {110} and {311} sites. This is not the ease for alanine and points toward higher site specificity in the case of alanine, which is eventually responsible for the enantiomeric differences observed for the alanine system.

Hydrogen bonded supramolecular elastomers : correlating hydrogen bonding strength with morphology and rheology

A series of six low molecular weight elastomers with hydrogen bonding end-groups have been designed, synthesised and studied. The poly(urethane) based elastomers all contained essentially the same hard block content (ca. 11%) and differ only in the nature of their end-groups. Solution state 1H NMR spectroscopic analysis of model compounds featuring the end-groups demonstrate that they all exhibit very low binding constants, in the range 1.4 to 45.0 M-1 in CDCl3, yet the corresponding elastomers each possess a markedly different nanoscale morphology and rheology in the bulk. We are able to correlate small variations of the binding constant of the end-groups with dramatic changes in the bulk properties of the elastomers. These results provide an important insight into the way in which weak non-covalent interactions can be utilized to afford a range of self-assembled polyurethane based materials that feature different morphologies.

Multistep electrochemical reduction path of clusters [Os3(CO)10(α-diimine)]: comparison of electrochemical and photochemical Os-Os(α-diimine) bond cleavage

Electrochemical reduction of the triangular clusters [Os-3(CO)(10)(alpha-dimine)] (alpha-dimine = 2,2'-bipyridine (bpy), 2,2'-bipyrimidine (bpym)) and [Os-3(CO)(10)(mu-bpym) ReBr(CO)(3)] produces primarily the corresponding radical anions. Their stability is strongly determined by the pi acceptor ability of the reducible alpha-dimine ligand, which decreases in the order mu-bpym > bpym >> bpy. Along this series, increasing delocalisation of the odd electron density in the radical anion over the Os(alpha-dimine) chelate ring causes weakening of the axial (CO)(4)Os-Os(CO)(2)(alpha-dimine) bond and its facile cleavage for alpha-diimine = bpy. In contrast, the cluster radical anion is inherently stable for the bridging bpym ligand, the strongest pi-acceptor in the studied series. In the absence of the partial delocalisation of the unpaired electron over the Re( bpym) chelate bond, the Os-3-core of the radical anion remains intact only at low temperatures. Subsequent one-electron reduction of [Os-3(CO)(10)(bpym)](center dot-) at T = 223 K gives the open-triosmium core (= Os-3*) dianion, [Os-3*(CO)(10)(bpym)](2-). Its oxidation leads to the recovery of parent [Os-3(CO)(10)( bpym)]. At room temperature, [Os-3*( CO)(10)(bpym)](2-) is formed along a two-electron (ECE) reduction path. The chemical step (C) results in the formation of an open- core radical anion that is directly reducible at the cathodic potential of the parent cluster in the second electrochemical (E) step. In weakly coordinating tetrahydrofuran, [Os-3*(CO)(10)( bpym)](2-) rapidly attacks yet non- reduced parent cluster molecules, producing the relatively stable open- core dimer [Os-3*(CO)(10)(bpym)](2)(2-) featuring two open- triangle cluster moieties connected with an ( bpym) Os - Os( bpym) bond. In butyronitrile, [Os-3*( CO)(10)(bpym)](2-) is stabilised by the solvent and the dimer [Os-3*(CO)(10)(bpym)](2)(2-) is then mainly formed by reoxidation of the dianion on reverse potential scan. The more reactive cluster [Os-3(CO)(10)(bpy)] follows the same reduction path, as supported by spectroelectrochemical results and additional valuable evidence obtained from cyclic voltammetric scans. The ultimate process in the reduction mechanism is fragmentation of the cluster core triggered by the reduction of the dimer [Os-3*(CO)(10)(alpha- diimine)](2)(2-). The products formed are [Os-2(CO)(8)](2-) and {Os(CO)(2)(alpha- diimine)}(2). The latter dinuclear fragments constitute a linear polymeric chain [Os( CO)(2)(alpha-dimine)] n that is further reducible at the alpha-dimine ligands. For alpha-dimine = bpy, the charged polymer is capable of reducing carbon dioxide. The electrochemical opening of the triosmium core in the [Os-3( CO)(10)(alpha-dimine)] clusters exhibits several common features with their photochemistry. The same Os-alpha-dimine bond dissociates in both cases but the intimate mechanisms are different.

The adsorption geometry and chemical state of lysine on Cu{110}

Chemisorbed layers of lysine adsorbed on Cu{110} have been studied using X-ray photoelectron spectroscopy (XPS) and near-edge X-ray absorption fine structure (NEXAFS) spectroscopy. XPS indicates that the majority (70%) of the molecules in the saturated layer at room temperature (coverage 0.27 ML) are in their zwitterionic state with no preferential molecular orientation. After annealing to 420 K a less densely packed layer is formed (0.14 ML), which shows a strong angular dependence in the characteristic π-resonance of oxygen K edge NEXAFS and no indication of zwitterions in XPS. These experimental results are best compatible with molecules bound to the substrate through the oxygen atoms of the (deprotonated) carboxylate group and the two amino groups involving Cu atoms in three different close packed rows. This μ4 bonding arrangement with an additional bond through the !-amino group is different from geometries previously suggested for lysine on Cu{110}.

Coordination behavior of pyridylmethylthioether system with cupric chloride and cupric bromide: CS bond cleavage and crystal structures

The coordination behavior of pyridylmethylthioether type of organic moieties having N2S2 donor set [L-1=1,2-bis(2-pyridylmethylthio)ethane, L-2 = 1,3-bis(2-pyridylmethyl-thio)propane and L-3 = 1,4-bis(2-pyridylmethylthio)butane] with copper(II) chloride and copper(II) bromide have been studied in different chemical environments. Copper(II) chloride assisted C-S bond cleavage of the organic moieties leading to the formation of copper(II) picolinate derivatives, whereas, under similar experimental conditions, no C-S bond cleavage was observed in the reaction with copper(II) bromide. The resulted copper(II) complexes isolated from the different mediums have been characterized by spectroscopic and X-ray crystallographic tools.