Improvement of link failure restoration utilising MPLS as a means to maintain QoS

The availability of a network strongly depends on the frequency of service outages and the recovery time for each outage. The loss of network resources includes complete or partial failure of hardware and software components, power outages, scheduled maintenance such as software and hardware, operational errors such as configuration errors and acts of nature such as floods, tornadoes and earthquakes. This paper proposes a practical approach to the enhancement of QoS routing by means of providing alternative or repair paths in the event of a breakage of a working path. The proposed scheme guarantees that every Protected Node (PN) is connected to a multi-repair path such that no further failure or breakage of single or double repair paths can cause any simultaneous loss of connectivity between an ingress node and an egress node. Links to be protected in an MPLS network are predefined and an LSP request involves the establishment of a working path. The use of multi-protection paths permits the formation of numerous protection paths allowing greater flexibility. Our analysis will examine several methods including single, double and multi-repair routes and the prioritization of signals along the protected paths to improve the Quality of Service (QoS), throughput, reduce the cost of the protection path placement, delay, congestion and collision.

Performance analysis of data transmissions in MPLS and non-MPLS networks

Basic Network transactions specifies that datagram from source to destination is routed through numerous routers and paths depending on the available free and uncongested paths which results in the transmission route being too long, thus incurring greater delay, jitter, congestion and reduced throughput. One of the major problems of packet switched networks is the cell delay variation or jitter. This cell delay variation is due to the queuing delay depending on the applied loading conditions. The effect of delay, jitter accumulation due to the number of nodes along transmission routes and dropped packets adds further complexity to multimedia traffic because there is no guarantee that each traffic stream will be delivered according to its own jitter constraints therefore there is the need to analyze the effects of jitter. IP routers enable a single path for the transmission of all packets. On the other hand, Multi-Protocol Label Switching (MPLS) allows separation of packet forwarding and routing characteristics to enable packets to use the appropriate routes and also optimize and control the behavior of transmission paths. Thus correcting some of the shortfalls associated with IP routing. Therefore MPLS has been utilized in the analysis for effective transmission through the various networks. This paper analyzes the effect of delay, congestion, interference, jitter and packet loss in the transmission of signals from source to destination. In effect the impact of link failures, repair paths in the various physical topologies namely bus, star, mesh and hybrid topologies are all analyzed based on standard network conditions.

Improvement of link failure restoration utilising multi-protocol label switching (MPLS) as a means to maintain quality of service (QOS)

This paper proposes a practical approach to the enhancement of Quality of Service (QoS) routing by means of providing alternative or repair paths in the event of a breakage of a working path. The proposed scheme guarantees that every Protected Node (PN) is connected to a multi-repair path such that no further failure or breakage of single or double repair paths can cause any simultaneous loss of connectivity between an ingress node and an egress node. Links to be protected in an MPLS network are predefined and a Label Switched path (LSP) request involves the establishment of a working path. The use of multi-protection paths permits the formation of numerous protection paths allowing greater flexibility. Our analysis examined several methods including single, double and multi-repair routes and the prioritization of signals along the protected paths to improve the Quality of Service (QoS), throughput, reduce the cost of the protection path placement, delay, congestion and collision. Results obtained indicated that creating multi-repair paths and prioritizing packets reduces delay and increases throughput in which case the delays at the ingress/egress LSPs were low compared to when the signals had not been classified. Therefore the proposed scheme provided a means to improve the QoS in path restoration in MPLS using available network resources. Prioritizing the packets in the data plane has revealed that the amount of traffic transmitted using a medium and low priority Label Switch Paths (LSPs) does not have any impact on the explicit rate of the high priority LSP in which case the problem of a knock-on effect is eliminated.

Economic transformation in Ghana: where will the path lead?

In the context of the Ghanaian government’s objective of structural transformation with an emphasis on manufacturing, this paper provides a case study of economic transformation in Ghana, exploring patterns of growth, sectoral transformation, and agglomeration. We document and examine why, despite impressive growth and poverty reduction figures, Ghana’s economy has exhibited less transformation than might be expected for a country that has recently achieved middle-income status. Ghana’s reduced share of agriculture in the economy, unlike many successfully transformed countries in Asia and Latin America, has been filled by services, while manufacturing has stagnated and even declined. Likely causes include weak transformation of the agricultural sector and therefore little development of agroprocessing, the emergence of consumption cities and consumption-driven growth, upward pressure on the exchange rate, weak production linkages, and a poor environment for private-sector-led manufacturing.

Economic Transformation in Ghana: Where Will the Path Lead?

In the context of the Ghanaian government’s objective of structural transformation with an emphasis on manufacturing, this paper provides a case study of economic transformation in Ghana, exploring patterns of growth, sector transformation, and agglomeration. We document and examine why, despite impressive growth and poverty reduction figures, Ghana’s economy has exhibited less transformation than might be expected for a country that has recently achieved middle-income status. Ghana’s reduced share of agriculture in the economy, unlike many successfully transformed countries in Asia and Latin America, has been filled by services, while manufacturing has stagnated and even declined. Likely causes include weak transformation of the agricultural sector and therefore little development of agro-processing, the emergence of “consumption cities” and consumption-driven growth, upward pressure on the exchange rate, weak production linkages, and a poor environment for private-sector-led manufacturing.