A comparison between bond graphs switching modelling techniques implemented on a boost dc-dc converter

A Bond Graph is a graphical modelling technique that allows the representation of energy flow between the components of a system. When used to model power electronic systems, it is necessary to incorporate bond graph elements to represent a switch. In this paper, three different methods of modelling switching devices are compared and contrasted: the Modulated Transformer with a binary modulation ratio (MTF), the ideal switch element, and the Switched Power Junction (SPJ) method. These three methods are used to model a dc-dc Boost converter and then run simulations in MATLAB/SIMULINK. To provide a reference to compare results, the converter is also simulated using PSPICE. Both quantitative and qualitative comparisons are made to determine the suitability of each of the three Bond Graph switch models in specific power electronics applications

Improvement of link failure restoration utilising multi-protocol label switching (MPLS) as a means to maintain quality of service (QOS)

This paper proposes a practical approach to the enhancement of Quality of Service (QoS) routing by means of providing alternative or repair paths in the event of a breakage of a working path. The proposed scheme guarantees that every Protected Node (PN) is connected to a multi-repair path such that no further failure or breakage of single or double repair paths can cause any simultaneous loss of connectivity between an ingress node and an egress node. Links to be protected in an MPLS network are predefined and a Label Switched path (LSP) request involves the establishment of a working path. The use of multi-protection paths permits the formation of numerous protection paths allowing greater flexibility. Our analysis examined several methods including single, double and multi-repair routes and the prioritization of signals along the protected paths to improve the Quality of Service (QoS), throughput, reduce the cost of the protection path placement, delay, congestion and collision. Results obtained indicated that creating multi-repair paths and prioritizing packets reduces delay and increases throughput in which case the delays at the ingress/egress LSPs were low compared to when the signals had not been classified. Therefore the proposed scheme provided a means to improve the QoS in path restoration in MPLS using available network resources. Prioritizing the packets in the data plane has revealed that the amount of traffic transmitted using a medium and low priority Label Switch Paths (LSPs) does not have any impact on the explicit rate of the high priority LSP in which case the problem of a knock-on effect is eliminated.

A single director switching mode for monodomain liquid crystal elastomer

We report rotation of a single director in a nematic monodomain, acrylate based side-chain elastomer which was subjected to mechanical fields applied at angles in the range to the director, , present at the time of network formation. Time and spatially resolving wide angle X-ray scattering, together with polarised light microscopy measurements revealed a pronounced, almost discontinuous switching mode at a critical extension as the strain was applied at angles approaching to , whereas a more continuous rotation was seen when the strain was applied at more acute angles. This director reorientation was more or less uniform across the complete sample and was accompanied by a modest decrease in orientation parameter . At strains sufficient to induce switching there was some continuous distribution of director orientations with fluctuations of 10 although there was no evidence for any localised director inhomogenities such as domain formation. The observed deformation behaviour of these acrylate-based nematic monodomains was in accord with the predictions of a theory developed by Bladon et al., in that the complete set of data could be accounted for through a single parameter describing the chain anisotropy. The experimentally deduced chain anisotropy parameter was in broad agreement with that obtained from small-angle neutron scattering procedures, but was somewhat greater than that obtained by spontaneous shape changes at the nematic-isotropic transition.

Property company performance and real interest rates: a regime-switching approach

Linear models of property market performance may be misspecified if there exist distinct states where the market drivers behave in different ways. This paper examines the applicability of non-linear regime-based models. A Self Exciting Threshold Autoregressive (SETAR) model is applied to property company share data, using the real rate of interest to define regimes. Distinct regimes appear exhibiting markedly different market behaviour. The model both casts doubt on the specification of conventional linear models and offers the possibility of developing effective trading rules for real estate equities.

Europe’s biocidal products directive: benefits and costs in urban pest management

The European Commission’s Biocidal Products Directive (Council Directive 98/8 EC), known as the BPD, is the largest regulatory exercise ever to affect the urban pest control industry. Although focussed in the European Union its impact is global because any company selling pest control products in the EU must follow its principles. All active substances, belonging to 23 different biocidal product types, come within the Directive’s scope of regulatory control. This will eventually involve re-registration of all existing products, as well as affecting any new product that comes to the market. Some active substances, such as the rodenticides and insecticides, are already highly regulated in Europe but others, such as embalming fluids, masonry preservatives, disinfectants and repellents/attractants will come under intensive regulatory scrutiny for the first time. One of the purposes of the Directive is to offer enhanced protection for human health and the environment. The potential benefit for suppliers of pest control products is mutual recognition of regulatory product dossiers across 25 Member States of the European Union. This process, requiring harmonisation of all regulatory decision-making processes, should reduce duplicated effort and, potentially, allow manufacturers speedier access to European markets. However, the cost to industry is enormous, both in terms of the regulatory resources required to assemble BPD dossiers and the development budgets required to conduct studies to meet its new standards. The cost to regulatory authorities is also tremendous, in terms of the need to upgrade staff capabilities to meet new challenges and the volume of the work expected by the Commission when they are appointed the Rapporteur Member State (RMS) for an active substance. Users of pest control products will pay a price too. The increased regulatory costs of maintaining products in the European market are likely to be passed on, at least in part, to users. Furthermore, where the costs of meeting new regulatory requirements cannot be recouped from product sales, many well-known products may leave the market. For example, it seems that in future few rodenticides that are not anticoagulants will be available within the EU. An understanding of the BPD is essential to those who intend to place urban pest control products on the European market and may be useful to those considering the harmonisation of regulatory processes elsewhere. This paper reviews the operation of the first stages of the BPD for rodenticides, examines the potential benefits and costs of the legislation to the urban pest control industry and looks forward to the next stages of implementation involving all insecticides used in urban pest management.