A comparative study of the main mechanisms controlling indoor air pollution in residential flats

The relative contribution of the main mechanisms that control indoor air quality in residential flats was examined. Indoor and outdoor concentration measurements of different type pollutants (black carbon, SO2, O3, NO, NO2,) were monitored in three naturally ventilated residential flats in Athens, Greece. At each apartment, experiments were conducted during the cold as well as during the warm period of the year. The controlling parameters of transport and deposition mechanisms were calculated from the experimental data. Deposition rates of the same pollutant differ according to the site (different construction characteristics) and to the measuring period for the same site (variations in relative humidity and differences in furnishing). Differences in the black carbon deposition rates were attributed to different black carbon size distributions. The highest deposition rates were observed for O3 in the residential flats with the older construction and the highest humidity levels. The calculated parameters as well as the measured outdoor concentrations were used as input data of a one-compartment indoor air quality model, and the indoor concentrations, the production, and loss rates of the different pollutants were calculated. The model calculated concentrations are in good agreement with the measured values. Model simulations revealed that the mechanism that mainly affected the change rate of indoor black carbon concentrations was the transport from the outdoor environment, while the removal due to deposition was insignificant. During model simulations, it was also established that that the change rate of SO2 concentrations was governed by the interaction between the transport and the deposition mechanisms while NOX concentrations were mainly controlled through photochemical reactions and the transport from outdoors.

Can valuation factors be prescribed? The case of collective enfranchisement and leasehold extension of flats in England and Wales

Recent concerns over the valuation process in collective leasehold enfranchisement and lease extension cases have culminated in new legislation. To underpin this, the Government (Department of Environment Transport and the Regions (DETR)) commissioned new research, which examined whether the valuation of the freehold in such cases could be simplified through the prescription of either yield or marriage value/relativity. This paper, which is based on that research, examines whether it is possible or desirable to prescribe such factors in the valuation process. Market, settlement and Local Valuation Tribunal (LVT) decisions are analysed, and the basis of 'relativity charts' used in practice is critically examined. Ultimately the imperfect nature of the market in freehold investment sales and leasehold vacant possession sales means that recommendations must rest on an analysis of LVT data. New relativity curves are developed from this data and used in conjunction with an alternative approach to valuation yields (based on other investment assets). However, the paper concludes that although the prescription of yields and relativity is possible, it is not fully defensible because of problems in determining risk premia; that the evidential basis for relativity consists of LVT decisions; and that a formula approach would tend to 'lead' the market as a whole.

Social housing in Latin America: Red Road flats of tomorrow?

The article revises latest social housing developments in Brazil and Chile and questions their ability to deliver liveable places.

Data assimilation for a coastal area morphodynamic model: Morecambe Bay

This paper investigates the use of data assimilation in coastal area morphodynamic modelling using Morecambe Bay as a study site. A simple model of the bay has been enhanced with a data assimilation scheme to better predict large-scale changes in bathymetry observed in the bay over a 3-year period. The 2DH decoupled morphodynamic model developed for the work is described, as is the optimal interpolation scheme used to assimilate waterline observations into the model run. Each waterline was acquired from a SAR satellite image and is essentially a contour of the bathymetry at some level within the inter-tidal zone of the bay. For model parameters calibrated against validation observations, model performance is good, even without data assimilation. However the use of data assimilation successfully compensates for a particular failing of the model, and helps to keep the model bathymetry on track. It also improves the ability of the model to predict future bathymetry. Although the benefits of data assimilation are demonstrated using waterline observations, any observations of morphology could potentially be used. These results suggest that data assimilation should be considered for use in future coastal area morphodynamic models.

An eclectic morphostratigraphic model for the sedimentary response to Holocene sea-level rise in northwest Europe

The improved empirical understanding of silt facies in Holocene coastal sequences provided by such as diatom, foraminifera, ostracode and testate amoebae analysis, combined with insights from quantitative stratigraphic and hydraulic simulations, has led to an inclusive, integrated model for the palaeogeomorphology, stratigraphy, lithofacies and biofacies of northwest European Holocene coastal lowlands in relation to sea-level behaviour. The model covers two general circumstances and is empirically supported by a range of field studies in the Holocene deposits of a number of British estuaries, particularly, the Severn. Where deposition was continuous over periods of centuries to millennia, and sea level fluctuated about a rising trend, the succession consists of repeated cycles of silt and peat lithofacies and biofacies in which series of transgressive overlaps (submergence sequences) alternate with series of regressive overlaps (emergence sequences) in association with the waxing and waning of tidal creek networks. Environmental and sea-level change are closely coupled, and equilibrium and secular pattern is of the kind represented ideally by a closed limit cycle. In the second circumstance, characteristic of unstable wetland shores and generally affecting smaller areas, coastal erosion ensures that episodes of deposition in the high intertidal zone last no more than a few centuries. The typical response is a series of regressive overlaps (emergence sequence) in erosively based high mudflat and salt-marsh silts that record, commonly as annual banding, exceptionally high deposition rates and a state of strong disequilibrium. Environmental change, including creek development, and sea-level movement are uncoupled. Only if deposition proceeds for a sufficiently long period, so that marshes mature, are equilibrium and close coupling regained. (C) 2002 Elsevier Science B.V. All rights reserved.

Seasonality of modern pollen and sediment deposition in an estuarine context: the Severn Estuary Levels, southwest England

Recent sedimentological and palynological research on subfossil Holocene banded sediments from the Severn Estuary Levels suggested seasonality of deposition, registered by variations in mineral grain-size and pollen assemblages between different parts of the bands. Here we provide data that strengthen this interpretation from sampling of modern sediments and pollen deposition on an active mudflat and saltmarsh on the margin of the Severn Estuary, and comparison with a vegetation survey and contemporary records of climate, river and tidal regimes. The results of grain-size analysis indicate deposition of comparatively coarse-grained silts during the relatively cool and windy conditions of winter and comparatively fine-grained sediments during relatively warm and calm summer months. Pollen analysis demonstrates the significance of long-term storage of pollen grains and fern spores in the estuarine waterbody, superimposed on which seasonal variations in pollen inputs from local and regional vegetation remain detectable. Copyright (C) 2007 John Wiley & Sons, Ltd.

Granulometric characterization and evaluation of annually banded mid-Holocene estuarine silts, Welsh Severn Estuary (UK): coastal change, sea level and climate

Holocene silts (salt marshes) and highest intertidal-supratidal peats are superbly exposed on a 15 kin coastal transect which reveals two laterally extensive units of annually banded silts (Beds 3, 7) associated with three transgressive-regressive silt-peat cycles (early sixth-early fourth millennium BC). Bed 3 in places is concordantly and gradationally related to peats above and below, but in others transgresses older strata. Bed 7 also grades up into peat, but everywhere overlies a discordance. The banding in Bed 3 at three main and two minor sites was resolved and characterized texturally at high-resolution (2.5/5 mm contiguous slices) using laser granulometry (LS230 with PIDS) and a comprehensive scheme of data-assessment. Most of Bed 3 formed very rapidly, at peak values of several tens of millimetres annually, in accordance with modelled effects of sea-level fluctuations on mature marshes (bed concordant and gradational) and on marshes growing up after coastal erosion and retreat (bed with discordant base). Using data from the modern Severn Estuary, the textural contrast within bands, and its variation between bands, points to a variable but overall milder mid-Holocene climate than today. The inter-annual variability affected marsh dynamics, as shown by the behaviour of the finely divided plant tissues present. Given local calibration, the methodology is applicable to other tidal systems with banded silts in Britain and mainland northwest Europe. (c) 2006 Elsevier Ltd. All rights reserved.

An ichnofabric approach to the depositional interpretation of the intensely burrowed Bateig Limestone, Miocene, SE Spain

The foraminiferal-rich pelagic Bateig Limestone forms several varieties of the important building stones quarried at Bateig Hill in southeastern Spain. Three principal ichnofabrics (Bichordites, mottled-Palaeophycus and mottled-Ophiomorpha) are recognized, which are present in at least two (possibly up to four) repeated successions (cycles). Each succession begins with an erosional event. The Bichordites ichnofabric represents a new type of facies, formed as thin turbidity/grain flow, stratiform units derived from sediment slips off a fault into deep water. Each slipped unit became almost completely bioturbated by infaunal echinoids, colonizing by lateral migration. Because of the thinness of the units, successive colonizations tended to truncate the underlying burrows giving rise to a pseudo-stratification. As the Bichordites ichnofabric accumulated on the fault apron, thus reducing the effective height of the fault scarp, the substrate gradually came under the influence of currents traversing the shelf. This led to a change in hydraulic regime, and to the mottled-Palaeophycus and mottled-Ophiomorpha ichnofabrics in sediment deposited under bed load transport, and associated with laminar and cross-stratified beds and local muddy intervals. Reactivation of the fault triggered erosion and channeling and a return to grain flow sedimentation, and to the Bichordites ichnofabric of the succeeding cycle. The highest unit of the Bateig Limestone is formed entirely of cross-stratified calcarenites with occasional Ophiomorpha (Ophiomorpha-primary lamination ichnofabric) and is similar to many shallow marine facies but they still bear a significant content of pelagic foraminifera. The sedimentary setting bears resemblance with that described for the Pleistocene Monte Torre Paleostrait and the modem Strait of Messina (Italy), where the narrow morphology of the depositional area enhanced tidal currents and allowed for high-energy sandy deposition in relatively deep areas. More data on the Miocene paleogeography of the Bateig area should provide further testing for this hypothesis. The ichnofacies and stacking of the Bateig Limestone differ from the classic Seilacherian model in that they reflect changes in hydraulic process and are associated with faulting and subsidence and changes in sediment supply. Recognition of the unusual ichnofabrics and their relationships provides a clear indication of the overall dynamic setting. (c) 2006 Elsevier B.V. All rights reserved.

Impact of Bt cotton on farmer livelihoods in South Africa

The economic benefits of Genetically Modified (GM) crops in developing countries have been well documented, but little research has been undertaken to date on the impacts of GM adoption on household livelihoods. The research reported here aimed to assess the livelihood impacts of the adoption of Bt cotton in South Africa., and involved 100 interviews of resource-poor farmers growing Bt cotton in Makhathini Flats, South Africa. Some 88% of respondents reported a higher income from Bt compared to non-Bt varieties previously grown by them, and this higher income was used primarily for greater education of their children (76%), more investment in growing cotton (46%), repaying debt (28%), investment in other crops (20%) and spending money on themselves. Some 89% had increased their asset base due to Bt cotton, primarily by increasing their cultivable land. These benefits of Bt adoption appeared widespread regardless of gender or farm size.

Bt-cotton boosts the gross margin of small-scale cotton producers in South Africa

This paper explores some of the issues involved in the Genetic Modification (GM) debate by focusing on one crop that has been modified for pest resistance, cotton (Gossypium hirsutum), and commercially released to small-scale farmers in the Makhathini Flats, KwaZulu Natal, the Republic of South Africa. This was the first commercial release of a GM variety (Bt-cotton) in Sub-Saharan Africa, and thus provides valuable and timely insights into some of the potential advantages and disadvantages of the technology for small-scale farmers in Africa. Even though there are wider concerns regarding the vulnerability of small-scale farmers in the area, the survey results suggest that Bt-cotton generated higher yields and gross margins than non-Bt-cotton. In addition, Bt-cotton significantly reduced the use of pesticide with consequent potential benefits to human health and the environment.

Environmental impact of genetically modified cotton in South Africa

This paper presents the results of a large-scale study designed to monitor the impact arising from the introduction of insect-resistant Bt cotton in the Makhathini Flats, Republic of South Africa. Bt cotton provides a degree of resistance to cotton bollworm complex (Lepidoptera). Data were collected on the use of insecticides (type and quantity) as well as the farm-level economics of production from over 2200 farmers in three growing seasons (1998/1999, 1999/2000 and 2000/2001). and the results are discussed within the context of environmental impact brought about by insecticide. Over the three seasons of the study it was clear that Bt cotton provided benefits in terms of higher yield and gross margin relative to farmers growing conventional (non-Bt) cotton, and the benefits were particularly apparent for the smallest producers. Bt growers also used significantly less insecticide than growers of non-Bt cotton. Once quantities of insecticide applied to Bt and non-Bt cotton were converted into a Biocide Index and an Environmental Impact Quotient (EIQ) in order to allow for differences in terms of toxicity and persistence in the environment, it was apparent that the growing of Bt had a less negative impact on the environment. While this points to beneficial impacts on agricultural sustainability there are wider concerns regarding the vulnerability of resource-poor farmers in an area with limited (as yet) marketing options for their product and options for livelihood diversification both within and outside agriculture. Cotton producers in Makhathini are vulnerable as they rely on just One company for inputs (including, credit) and for their market. While Bt cotton provides benefits it does not in itself address some of the structural limitations that farmers face. (c) 2006 Elsevier B.V. All rights reserved.

Can genetically-modified cotton contribute to sustainable development in Africa?

Genetically modified (GM) crops and sustainable development remain the foci of much media attention, especially given current concerns about a global food crisis. However, whilst the latter is embraced with enthusiasm by almost all groups, GM crops generate very mixed views. Some countries have welcomed GM, but others, notably those in Europe, adopt a cautious stance. This article aims to review the contribution that GM crops can make to agricultural sustainability in the developing world. Following brief reviews of both issues and their linkages, notably the pros and cons of GM cotton as a contributory factor in sustainability, a number of case studies from resourcepoor cotton farmers in Makhathini Flats, South Africa, is presented for a six-year period. Data on expenditure, productivity and income indicate that Bacillus thuringiensis (Bt) cotton is advantageous because it reduces costs, for example, of pesticides, and increases income, and the indications are that those benefits continued over at least the six years covered by the studies. There are repercussions of the additional income in the households; debts are reduced and money is invested in children's education and in the farms. However, in the general GM debate, the results show that GM crops are not miracle products which alleviate poverty at a stroke, but nor is there evidence that they will cause the scale of environmental damage associated with indiscriminate pesticide use. Indeed, for some GM antagonists, perhaps even the majority, such debates are irrelevant – the transfer of genes between species is unnatural and unethical. For them, GM crops will never be acceptable despite the evidence and pressure to increase world food production.

Response of the lower St. Lawrence Estuary to external forcing in winter

Mostly because of a lack of observations, fundamental aspects of the St. Lawrence Estuary's wintertime response to forcing remain poorly understood. The results of a field campaign over the winter of 2002/03 in the estuary are presented. The response of the system to tidal forcing is assessed through the use of harmonic analyses of temperature, salinity, sea level, and current observations. The analyses confirm previous evidence for the presence of semidiurnal internal tides, albeit at greater depths than previously observed for ice-free months. The low-frequency tidal streams were found to be mostly baroclinic in character and to produce an important neap tide intensification of the estuarine circulation. Despite stronger atmospheric momentum forcing in winter, the response is found to be less coherent with the winds than seen in previous studies of ice-free months. The tidal residuals show the cold intermediate layer in the estuary is renewed rapidly ( 14 days) in late March by the advection of a wedge of near-freezing waters from the Gulf of St. Lawrence. In situ processes appeared to play a lesser role in the renewal of this layer. In particular, significant wintertime deepening of the estuarine surface mixed layer was prevented by surface stability, which remained high throughout the winter. The observations also suggest that the bottom circulation was intensified during winter, with the intrusion in the deep layer of relatively warm Atlantic waters, such that the 3 C isotherm rose from below 150 m to near 60 m.

High-resolution, unstructured meshes for hydrodynamic models of the Great Barrier Reef, Australia

Accuracy and mesh generation are key issues for the high-resolution hydrodynamic modelling of the whole Great Barrier Reef. Our objective is to generate suitable unstructured grids that can resolve topological and dynamical features like tidal jets and recirculation eddies in the wake of islands. A new strategy is suggested to refine the mesh in areas of interest taking into account the bathymetric field and an approximated distance to islands and reefs. Such a distance is obtained by solving an elliptic differential operator, with specific boundary conditions. Meshes produced illustrate both the validity and the efficiency of the adaptive strategy. Selection of refinement and geometrical parameters is discussed. (c) 2006 Elsevier Ltd. All rights reserved.