Recovery of gallic acid with colloidal gas aphrons (CGA)

In the present paper the potential application of colloidal gas aphrons (CGA) to the recovery of antioxidants from wine-making waste extracts is investigated. CGA were generated by stirring a buffered solution (400 ml) of a cationic surfactant(cetyltrimethylammonium bromide, CTAB) at 8000 rpm for 10 minutes. Trials were carried out on standard solutions (2 ml) of gallic acid (GA) 200 mg/l with varying volumes of colloidal gas aphrons (20-60 ml) generated with varying concentrations of CTAB (2 and 4 mM). Influence of pH, solvent (buffered aqueous solution and ethanol), CTAB to GA molar ratio on recovery were studied. Best recovery (63%) was achieved from an aqueous solution of GA and at a CTAB to GA molar ratio of 16. Separation is mainly driven by electrostatic interactions but pH conditions are to be optimised to preserve the GA antioxidant power.

An insight into the mechanism of protein separation by colloidal gas aphrons (CGA) generated from ionic surfactants

Colloidal gas aphrons (CGA), which are surfactant stabilised microbubbles, have been previously applied for the recovery of proteins from model mixtures and a few studies have demonstrated the potential of these dispersions for the selective recovery of proteins from complex mixtures. However there is a lack of understanding of the mechanism of separation and forces governing the selectivity of the separation. In this paper a mechanistic study is carried out to determine the main factors and forces influencing the selectivity of separation of whey proteins with CGA generated from ionic surfactants. Two different separation strategies were followed: (i) separation of lactoferrin and lactoperoxidase by anionic CGA generated from a solution of sodium bis-(2-ethyl hexyl) sulfosuccinate (AOT); (ii) separation of beta-lactoglobulin by cationic CGA generated from a solution of cetyltrimethylammonium bromide (CTAB). Separation results indicate that electrostatic interactions are the main forces determining the selectivity however these could not completely explain the selectivities obtained following both strategies. Protein-surfactant interactions were studied by measuring the zeta potential changes on individual proteins upon addition of surfactant and at varying pH. Interestingly strongest electrostatic interactions were measured at those pH and surfactant to protein mass ratios which were optimum for protein separation. Effect of surfactant on protein conformation was determined by measuring the change in fluorescence intensity upon addition of surfactant at varying pH. Differences in the fluorescence patterns were detected among proteins which were correlated to differences in their conformational features which could in turn explain their different separation behaviour. The effect of conformation on selectivity was further proven by experiments in which conformational changes were induced by pre-treatment of whey (heating) and by storage at 4 degrees C. Overall it can be concluded that separation of proteins by ionic CGA is driven mainly by electrostatic interactions however conformational features will finally determine the selectivity of the separation with competitive adsorption having also an effect. (c) 2006 Elsevier B.V. All rights reserved.

Selective separation of beta-lactoglobulin from sweet whey using CGAs generated from the cationic surfactant CTAB

The selective separation of whey proteins was studied using colloidal gas aphrons generated from the cationic surfactant cetyl trimethyl ammonium bromide (CTAB). From the titration curves obtained by zeta potential measurements of individual whey proteins, it was expected to selectively adsorb the major whey proteins, i.e., bovine serum albumin, alpha-lactalbumin, and beta-lactoglobulin to the aphrons and elute the remaining proteins (lactoferrin and lactoperoxidase) in the liquid phase. A number of process parameters including pH, ionic strength, and mass ratio of surfactant to protein (M-CTAB/M-TP) were varied in order to evaluate their effect on protein separation. Under optimum conditions (2 mmol/l CTAB, M-CTAB/M-TP = 0.26-0.35, pH 8, and ionic strength = 0.018 mol/l), 80-90% beta-lactoglobulin was removed from the liquid phase as a precipitate, while about 75% lactoferrin and lactoperoxidase, 80% bovine serum albumin, 95% immunoglobulin, and 65% alpha-lactalbumin were recovered in the liquid fraction. Mechanistic studies using zeta potential measurements and fluorescence spectroscopy proved that electrostatic interactions modulate only partially the selectivity of protein separation, as proteins with similar surface charges do not separate to the same extent between the two phases. The selectivity of recovery of beta-lactoglobulin probably occurs in two steps: the first being the selective interaction of the protein with opposite-charged surfactant molecules by means of electrostatic interactions, which leads to denaturation of the protein and subsequent formation and precipitation of the CTAB-beta-lactoglobulin complex. This is followed by the separation of CTAB-beta-lactoglobulin aggregates from the bulk liquid by flotation in the aphron phase. In this way, CGAs act as carriers which facilitate the removal of protein precipitate. (c) 2005 Wiley Periodicals, Inc.

Recovery of astaxanthin using colloidal gas aphrons (CGA): a mechanistic study

The aim of this study is to investigate the mechanism responsible for the recovery of astaxanthin using Colloidal Gas Aphrons (CGA), which are surfactant stabilised microbubbles. The latter were produced using different surfactant solutions (Cetyl Trimethyl Ammonium Bromide (CTAB)-cationic, Sodium Dodecyl Sulfate (SDS)-anionic, TWEEN 60-non-ionic and mixtures of TWEEN 60-SPAN 80- non-ionic with varying hydrophobicity) at stirring speed 8000 rpm and stirring time 5 min. Experiments were carried out at varying pH and volumetric ratios of astaxanthin to CGA, and with two different astaxanthin standard suspensions: (i) astaxanthin dispersed in aqueous solutions and (ii) astaxanthin dispersed in ethanolic/aqueous solutions with different compositions of ethanol (20/80 (v/v) and 40/60 (v/v)). When astaxanthin is dispersed in aqueous solutions the separation seems to occur mainly by electrostatic interactions. Therefore the recoveries are higher in the case of the cationic surfactant when astaxanthin particles are strongly negatively charged, as shown by the zeta potential measurements. When ethanol is present, highest recoveries are achieved with CGA produced from the non-ionic surfactant, which indicates that, under these conditions, separation is driven mainly by hydrophobic interactions. In experiments with ethanolic/aqueous suspensions, when the hydrophobicity of the surfactant was increased by increasing volumes of SPAN 80, the CGA produced were less stable; thus higher recoveries of astaxanthin under conditions that favour hydrophobic interactions were not observed. (C) 2008 Elsevier B.V All rights reserved.

The use of colloidal gas aphrons as novel downstream processing for the recovery of astaxanthin from cells of Phaffia rhodozyma

BACKGROUND: There is an increasing interest in obtaining natural products with bioactive properties, using fermentation technology. However, the downstream processing consisting of multiple steps can be complicated, leading to increase in the final cost of the product. Therefore there is a need for integrated, cost-effective and scalable separation processes. RESULTS: The present study investigates the use of colloidal gas aphrons (CGA), which are surfactant-stabilized microbubbles, as a novel method for downstream processing. More particularly, their application for the recovery of astaxanthin from the cells of Phaffia rhodozyma is explored. Research carried out with standard solutions of astaxanthin and CGA generated from the cationic surfactant hexadecyl. trimethyl ammonium bromide (CTAB) showed that up to 90% recovery can be achieved under optimum conditions, i.e., pH 11 with NaOH 0.2 mol L-1. In the case of the cells' suspension from the fermentation broth, three different approaches were investigated: (a) the conventional integrated approach where CGA were applied directly; (b) CGA were applied to the clarified suspension of cells; and finally (c) the in situ approach, where CGA are generated within the clarified suspension of cells. Interestingly, in the case of the whole suspension (approach a) highest recoveries (78%) were achieved under the same conditions found to be optimal for the standard solutions. In addition, up to 97% recovery of total carotenoids could be achieved from the clarified suspension after pretreatment with NaOH. This pretreatment led to maximum cell disruption as well as optimum conditioning for subsequent CGA separation. CONCLUSIONS: These results demonstrate the potential of CGA for the recovery of bioactive components from complex feedstock. (c) 2008 Society of Chemical Industry.

Antibacterials and modulators of bacterial resistance from the immature cones of Chamaecyparis lawsoniana

As part of an on-going project to characterize compounds from immature conifer cones with antibacterial or modulatory activity against multidrug-resistant (MDR) strains of Staphylococcus aureus, eight compounds were isolated from the cones of Chatnaecyparis lawsoniana. The active compounds were mainly diterpenes, with minimum inhibitory concentrations ranging from 4 to 128 mu g/ml against MDR effluxing S. aureus strains and two epidemic methicillin-resistant (EMRSA) clinical isolates. The compounds extracted were the diterpenes ferruginol, pisiferol and its epimer 5-epipisiferol, formosanoxide, trans-communic acid and torulosal, the sesquiterpene oplopanonyl acetate and the germacrane 4 beta-hydroxygermacra-1(10)-5-diene. Some of these compounds also exhibited modulatory activity in potentiating antibiotic activity against effluxing strains and ferruginol, used at a sub-inhibitory concentration, resulted in an 80-fold potentiation of oxacillin activity against strain EMRSA-15. An efflux inhibition assay using an S. aureus strain possessing the MDR NorA efflux pump resulted in 40% inhibition of ethidium bromide efflux at 10 mu M ferruginol (2.86 mu g/ml). We report the H-1 and C-13 NMR data for the cis A/B ring junction epimer of pisiferol which we have named 5-epipisiferol. We also unambiguously assign all H-1 and C-13 NMR resonances for trans-communic acid. (c) 2006 Elsevier Ltd. All rights reserved.

Effect of headgroup size, charge, and solvent structure on polymer−micelle interactions, studied by molecular dynamics simulations

We performed atomistic molecular dynamics simulations of anionic and cationic micelles in the presence of poly(ethylene oxide) (PEO) to understand why nonionic water-soluble polymers such as PEO interact strongly with anionic micelles but only weakly with cationic micelles. Our micelles include sodium n-dodecyl sulfate (SDS), n-dodecyl trimethylammonium chloride (DTAC), n-dodecyl ammonium chloride (DAC), and micelles in which we artificially reverse the sign of partial charges in SDS and DTAC. We observe that the polymer interacts hydrophobically with anionic SDS but only weakly with cationic DTAC and DAC, in agreement with experiment. However, the polymer also interacts with the artificial anionic DTAC but fails to interact hydrophobically with the artificial cationic SDS, illustrating that large headgroup size does not explain the weak polymer interaction with cationic micelles. In addition, we observe through simulation that this preference for interaction with anionic micelles still exists in a dipolar "dumbbell" solvent, indicating that water structure and hydrogen bonding alone cannot explain this preferential interaction. Our simulations suggest that direct electrostatic interactions between the micelle and polymer explain the preference for interaction with anionic micelles, even though the polymer overall carries no net charge. This is possible given the asymmetric distribution of negative charges on smaller atoms and positive charges oil larger units in the polymer chain.

Reactive Halogens in the Marine Boundary Layer (RHaMBLe): the tropical North Atlantic experiments

The NERC UK SOLAS-funded Reactive Halogens in the Marine Boundary Layer (RHaMBLe) programme comprised three field experiments. This manuscript presents an overview of the measurements made within the two simultaneous remote experiments conducted in the tropical North Atlantic in May and June 2007. Measurements were made from two mobile and one ground-based platforms. The heavily instrumented cruise D319 on the RRS Discovery from Lisbon, Portugal to São Vicente, Cape Verde and back to Falmouth, UK was used to characterise the spatial distribution of boundary layer components likely to play a role in reactive halogen chemistry. Measurements onboard the ARSF Dornier aircraft were used to allow the observations to be interpreted in the context of their vertical distribution and to confirm the interpretation of atmospheric structure in the vicinity of the Cape Verde islands. Long-term ground-based measurements at the Cape Verde Atmospheric Observatory (CVAO) on São Vicente were supplemented by long-term measurements of reactive halogen species and characterisation of additional trace gas and aerosol species during the intensive experimental period. This paper presents a summary of the measurements made within the RHaMBLe remote experiments and discusses them in their meteorological and chemical context as determined from these three platforms and from additional meteorological analyses. Air always arrived at the CVAO from the North East with a range of air mass origins (European, Atlantic and North American continental). Trace gases were present at stable and fairly low concentrations with the exception of a slight increase in some anthropogenic components in air of North American origin, though NOx mixing ratios during this period remained below 20 pptv (note the non-IUPAC adoption in this manuscript of pptv and ppbv, equivalent to pmol mol−1 and nmol mol−1 to reflect common practice). Consistency with these air mass classifications is observed in the time series of soluble gas and aerosol composition measurements, with additional identification of periods of slightly elevated dust concentrations consistent with the trajectories passing over the African continent. The CVAO is shown to be broadly representative of the wider North Atlantic marine boundary layer; measurements of NO, O3 and black carbon from the ship are consistent with a clean Northern Hemisphere marine background. Aerosol composition measurements do not indicate elevated organic material associated with clean marine air. Closer to the African coast, black carbon and NO levels start to increase, indicating greater anthropogenic influence. Lower ozone in this region is possibly associated with the increased levels of measured halocarbons, associated with the nutrient rich waters of the Mauritanian upwelling. Bromide and chloride deficits in coarse mode aerosol at both the CVAO and on D319 and the continuous abundance of inorganic gaseous halogen species at CVAO indicate significant reactive cycling of halogens. Aircraft measurements of O3 and CO show that surface measurements are representative of the entire boundary layer in the vicinity both in diurnal variability and absolute levels. Above the inversion layer similar diurnal behaviour in O3 and CO is observed at lower mixing ratios in the air that had originated from south of Cape Verde, possibly from within the ITCZ. ECMWF calculations on two days indicate very different boundary layer depths and aircraft flights over the ship replicate this, giving confidence in the calculated boundary layer depth.

In vitro micro-tuber initiation and dormancy in yam

Dormancy is a mechanism that regulates the timing of sprouting (germination) of affected plant parts as well as ensures that the food quality of edible parts is maintained in storage until the following growing season. In yam, however, little is known about the control of tuber initiation or tuber dormancy. The objective of this study was to determine the effects of selected plant growth regulators (PGRs) on tuber initiation and dormancy, using an in vitro system. In two replicated experiments, 2-chloroethylphosphonic acid (ethephon, an ethylene source), abscisic acid (ABA) and gibberellin (GA3) – and their inhibitors silver nitrate, fluridone and 2-chloroethyl-trimethylammonium chloride, respectively – were added at two concentrations to the culture medium prior to explant culture. Dates of micro-tuber initiation and sprouting (end of dormancy) and tuber number were recorded. In the control (no PGR) in Experiment 1, micro-tubers were initiated at the base of the stem after 176 days and sprouted 235 days later, that is 411 days after culturing. Most PGR treatments had only small effects (±30 days) on the duration of dormancy and the time of micro-tuber initiation. However, in GA3 micro-tuber initiation occurred after 76 days, about 100 days earlier than in the control, whereas fluridone affected the position of micro-tubers and duration of dormancy. With fluridone treatments, tubers were found at the base of the stem (normal position) and on lower and upper nodes. Lower node tubers sprouted within 225 days of culturing compared with about 420 days after culturing at other nodal positions and in other PGR treatments. These data suggest an important role for ABA and gibberellic acid in yam micro-tuber initiation and the induction of dormancy.

Spectro-electrochemical and DFT studies of a planar Cu(II)–phenolate complex active in the aerobic oxidation of primary alcohols

A square-planar compound [Cu(pyrimol)Cl] (pyrimol = 4-methyl-2-N-(2-pyridylmethylene)aminophenolate) abbreviated as CuL–Cl) is described as a biomimetic model of the enzyme galactose oxidase (GOase). This copper(II) compound is capable of stoichiometric aerobic oxidation of activated primary alcohols in acetonitrile/water to the corresponding aldehydes. It can be obtained either from Hpyrimol (HL) or its reduced/hydrogenated form Hpyramol (4-methyl-2-N-(2-pyridylmethyl)aminophenol; H2L) readily converting to pyrimol (L-) on coordination to the copper(II) ion. Crystalline CuL–Cl and its bromide derivative exhibit a perfect square-planar geometry with Cu–O(phenolate) bond lengths of 1.944(2) and 1.938(2) Å. The cyclic voltammogram of CuL–Cl exhibits an irreversible anodic wave at +0.50 and +0.57 V versus ferrocene/ferrocenium (Fc/Fc+) in dry dichloromethane and acetonitrile, respectively, corresponding to oxidation of the phenolate ligand to the corresponding phenoxyl radical. In the strongly donating acetonitrile the oxidation path involves reversible solvent coordination at the Cu(II) centre. The presence of the dominant CuII–L. chromophore in the electrochemically and chemically oxidised species is evident from a new fairly intense electronic absorption at 400–480 nm ascribed to a several electronic transitions having a mixed pi-pi(L.) intraligand and Cu–Cl -> L. charge transfer character. The EPR signal of CuL–Cl disappears on oxidation due to strong intramolecular antiferromagnetic exchange coupling between the phenoxyl radical ligand (L.) and the copper(II) centre, giving rise to a singlet ground state (S = 0). The key step in the mechanism of the primary alcohol oxidation by CuL–Cl is probably the alpha-hydrogen abstraction from the equatorially bound alcoholate by the phenoxyl moiety in the oxidised pyrimol ligand, Cu–L., through a five-membered cyclic transition state.

Separation of astaxanthin from cells of Phaffia rhodozyma using colloidal gas aphrons (CGA) in a flotation column

The aim of this study is to investigate the separation of astaxanthin from the cells of Phaffia rhodozyma using colloidal gas aphrons (CGA), which are surfactant stabilized microbubbles, in a flotation column. It was reported in previous studies that optimum recoveries are achieved at conditions that favor electrostatic interactions. Therefore, in this study, CGA generated from the cationic surfactant hexadecyl trimethyl ammonium bromide (CTAB) were applied to suspensions of cells pretreated with NaOH. The different operation modes (batch or continuous) and the effect of volumetric ratio of CGA to feed, initial concentration of feed, operating height, and flow rate of CGA on the separation of astaxanthin were investigated. The volumetric ratio was found to have a significant effect on the separation of astaxanthin for both batch and continuous experiments. Additionally, the effect of homogenization of the cells on the purity of the recovered fractions was investigated, showing that the homogenization resulted in increased purity. Moreover, different concentrations of surfactant were used for the generation of CGA for the recovery of astaxanthin on batch mode; it was found that recoveries up to 98% could be achieved using CGA generated from a CTAB solution 0.8 mM, which is below the CTAB critical micellar concentration (CMC). These results offer important information for the scale-up of the separation of astaxanthin from the cells of P. rhodozyma using CGA.

Recovery of gallic acid with colloidal gas aphrons generated from a cationic surfactant

In a previous study we have demonstrated that gallic acid (GA) in its anionic form can be recovered from aqueous solutions using colloidal gas aphrons (CGA) generated from the cationic surfactant cetyltrimethylammonium bromide (CTAB). The aim of the present work is to get a better understanding of the separation mechanism in order to determine the optimum operating conditions to maximise the recovery of GA while preserving its antioxidant properties. Zeta potential measurements were carried out to characterise the surface charge of GA, CTAB and their mixtures at three different pH conditions (both in buffers and in aqueous solutions). GA interacted strongly with CTAB at pH higher than its pKa 3.14 where it is ionised and negatively charged. However, at pH higher than 7 GA becomes oxidised and loses its antioxidant power. GA recovery was mainly affected by pH, ionic strength, surfactant/GA molar ratio, mixing conditions and contact time. Scale-up of the separation using a flotation column resulted in both higher recovery and reproducibility. Preliminary experiments with grape marc extracts confirmed the potential application of this separation for the recovery of polyphenols from complex feedstocks

Inducible hydrogen sulfide synthesis in chondrocytes and mesenchymal progenitor cells: is H2S a novel cytoprotective mediator in the inflamed joint?

Hydrogen sulfide (H(2)S) has recently been proposed as an endogenous mediator of inflammation and is present in human synovial fluid. This study determined whether primary human articular chondrocytes (HACs) and mesenchymal progenitor cells (MPCs) could synthesize H(2)S in response to pro-inflammatory cytokines relevant to human arthropathies, and to determine the cellular responses to endogenous and pharmacological H(2)S. HACs and MPCs were exposed to IL-1β, IL-6, TNF-α and lipopolysaccharide (LPS). The expression and enzymatic activity of the H(2)S synthesizing enzymes cystathionine-β-synthase (CBS) and cystathionine-γ-lyase (CSE) were determined by Western blot and zinc-trap spectrophotometry, respectively. Cellular oxidative stress was induced by H(2)O(2), the peroxynitrite donor SIN-1 and 4-hydroxynonenal (4-HNE). Cell death was assessed by 3-(4,5-dimethyl-2-yl)-2,5-diphenyltetrazolium bromide (MTT) and lactate dehydrogenase (LDH) assays. Mitochondrial membrane potential (DCm) was determined in situ by flow cytometry. Endogenous H(2) S synthesis was inhibited by siRNA-mediated knockdown of CSE and CBS and pharmacological inhibitors D,L-propargylglycine and aminoxyacetate, respectively. Exogenous H(2)S was generated using GYY4137. Under basal conditions HACs and MPCs expressed CBS and CSE and synthesized H(2)S in a CBS-dependent manner, whereas CSE expression and activity was induced by treatment of cells with IL-1β, TNF-α, IL-6 or LPS. Oxidative stress-induced cell death was significantly inhibited by GYY4137 treatment but increased by pharmacological inhibition of H(2)S synthesis or by CBS/CSE-siRNA treatment. These data suggest CSE is an inducible source of H(2)S in cultured HACs and MPCs. H(2)S may represent a novel endogenous mechanism of cytoprotection in the inflamed joint, suggesting a potential opportunity for therapeutic intervention.

Prevalence of multiple antibiotic resistance in 443 Campylobacter spp. isolated from humans and animals

Aims: In view of recent findings that a multidrug efflux pump CmeABC exists in Campylobacter jejuni, 391 C. jejuni and 52 Campylobacter coli of human and animal origin were examined for a multidrug resistance phenotype. Materials and methods: The MICs of ampicillin, chloramphenicol, ciprofloxacin, erythromycin, kanamycin, tetracycline, cetrimide, triclosan, acridine orange, paraquat and ethidium bromide were determined. Resistance to organic solvents and the effect of salicylate (known inducer of the marRAB operon in Escherichia coli and Salmonella) were also examined. Results: Two C. coli and 13 C. jejuni isolates, mainly from pigs or poultry, were resistant to three or more antibiotics and 12 of these strains had reduced susceptibility to acridine orange and/or ethidium bromide. Strains (n=20) that were less susceptible to acridine orange, ethidium bromide and triclosan were significantly more resistant (P<0.05) to ampicillin, chloramphenicol, ciprofloxacin, erythromycin, nalidixic acid and tetracycline, with two- to four-fold increases in MIC values compared with strains (n=20) most susceptible to acridine orange, ethidium bromide and triclosan. Growth of strains with 1 mM salicylate caused a small (up to two-fold) but statistically significant (Pless than or equal to0.005) increase in the MICs of chloramphenicol, ciprofloxacin, erythromycin and tetracycline. Conclusions: These data indicate that multiple antibiotic resistant (MAR)-like Campylobacter strains occur and it may be postulated that these may overexpress cmeABC or another efflux system.

Expression of the efflux pump genes cmeB, cmeF and the porin gene porA in multiple-antibiotic-resistant Campylobacter jejuni

Aims: In Escherichia coli, increased expression of efflux pumps and/or decreased expression of porins can confer multiple antibiotic resistance (MAR), causing resistance to at least three unrelated classes of antibiotics, detergents and dyes. It was hypothesized that in Campylobacter jejuni, the efflux systems CmeABC, CmeDEF and the major outer membrane porin protein, MOMP (encoded by porA) could confer MAR. Methods: The expression of cmeB, cmeF and porA in 32 MAR C. jejuni isolated from humans or poultry was determined by comparative (C)-reverse transcriptase (RT)-PCR and denaturing DHPLC. A further 13 ethidium bromide-resistant isolates and three control strains were also investigated. Accumulation of ciprofloxacin carbonyl cyanide-m-chlorophenyl hydrazone (CCCP) was also determined for all strains. Results: Although resistance to ethidium bromide has been associated with MAR, expression of all three genes was similar in the ethidium bromide-resistant isolates. These data indicate that CmeB, CmeF and MOMP play no role in resistance to this agent in C. jejuni. Six MAR isolates over-expressed cmeB, 3/32 over-expressed cmeB and cmeF. No isolates over-expressed cmeF alone. Expression of porA was similar in all isolates. All nine isolates that over-expressed cmeB contained a mutation in cmeR, substituting glycine 86 with alanine. All cmeB over-expressing isolates also accumulated low concentrations of ciprofloxacin, which were restored to wild-type levels in the presence of CCCP. Conclusions: These data indicate that over-expression of cmeB is associated with MAR in isolates of C. jejuni. However, as cmeB was over-expressed by only one-third (9/32) of MAR isolates, these data also indicate other mechanisms of MAR in C. jejuni.