Displacement of Zn through acidic light-textured soils

In order to gain understanding of the movement of pollutant metals in soil. the chemical mechanisms involved in the transport of zinc were studied. The displacement of zinc through mixtures of sand and cation exchange resin was measured to validate the methods used for soil. With cation exchange capacities of 2.5 and 5.0 cmol(c) kg(-1). 5.6 and 8.4 pore volumes of 10 mM CaCl2, respectively, were required to displace a pulse of ZnCl2. A simple Burns-type model (Wineglass) using an adsorption coefficient (K-d) determined by fitting a straight line relationship to an adsorption isotherm gave a good fit to the data (K-d=0.73 and 1.29 ml g(-1), respectively). Surface and subsurface samples of an acidic sandy loam (organic matter 4.7 and 1.0%. cation exchange capacity (CEC) 11.8 and 6.1 cmol(c) kg(-1) respectively) were leached with 10 mM calcium chloride. nitrate and perchlorate. With chloride. the zinc pulse was displaced after 25 and 5 pore volumes, respectively. The Kd values were 6.1 and 2.0 ml g(-1). but are based on linear relationships fitted to isotherms which are both curved and show hysteresis. Thus. a simple model has limited value although it does give a general indication of rate of displacement. Leaching with chloride and perchlorate gave similar displacement and Kd values, but slower movement occurred with nitrate in both soil samples (35 and 7 pore volumes, respectively) which reflected higher Kd values when the isotherms were measured using this anion (7.7 and 2.8 ml g(-1) respectively). Although pH values were a little hi-her with nitrate in the leachates, the differences were insufficient to suggest that this increased the CEC enough to cause the delay. No increases in pH occurred with nitrate in the isotherm experiments. Geochem was used to calculate the proportions of Zn complexed with the three anions and with fulvic acid determined from measurements of dissolved organic matter. In all cases, more than 91% of the Zn was present as Zn2+ and there were only minor differences between the anions. Thus, there is an unexplained factor associated with the greater adsorption of Zn in the presence of nitrate. Because as little as five pore volumes of solution displaced Zn through the subsurface soil, contamination of ground waters may be a hazard where Zn is entering a light-textured soil, particularly where soil salinity is increased. Reductions in organic matter content due to cultivation will increase the hazard. (C) 2004 Elsevier B.V. All rights reserved.

Distribution and mobility of trace elements in soils and vegetation around the mining and smelting areas of Tharsis, Riotinto and Huelva, Iberian Pyrite Belt, SW Spain

Trace elements may present an environmental hazard in the vicinity of mining and smelting activities. However, the factors controlling their distribution and transfer within the soil and vegetation systems are not always well defined. Total concentrations of up to 15,195 mg center dot kg (-1) As, 6,690 mg center dot kg(-1) Cu, 24,820 mg center dot kg(-1) Pb and 9,810 mg center dot kg(-1) Zn in soils, and 62 mg center dot kg(-1) As, 1,765 mg center dot kg(-1) Cu, 280 mg center dot kg(-1) Pb and 3,460 mg center dot kg (-1) Zn in vegetation were measured. However, unusually for smelters and mines of a similar size, the elevated trace element concentrations in soils were found to be restricted to the immediate vicinity of the mines and smelters (maximum 2-3 km). Parent material, prevailing wind direction, and soil physical and chemical characteristics were found to correlate poorly with the restricted trace element distributions in soils. Hypotheses are given for this unusual distribution: (1) the contaminated soils were removed by erosion or (2) mines and smelters released large heavy particles that could not have been transported long distances. Analyses of the accumulation of trace elements in vegetation (median ratios: As 0.06, Cu 0.19, Pb 0.54 and Zn 1.07) and the percentage of total trace elements being DTPA extractable in soils (median percentages: As 0.06%, Cu 15%, Pb 7% and Zn 4%) indicated higher relative trace element mobility in soils with low total concentrations than in soils with elevated concentrations.

A preliminary investigation into mining and smelting impacts on trace element concentrations in the soils and vegetation around Tharsis, SW Spain

Toxic trace elements present an environmental hazard in the vicinity of mining and smelting activities. However. the processes of transfer of these elements to groundwater and to plants are not always clear. Tharsis mine. in the Iberian pyrite belt (SW Spain), has been exploited since 2500 BC, with extensive smelting, taking place front the 1850S until the 1920s. Sixty four soil (mainly topsoils) and vegetation samples were collected in February 2001 and analysed by ICP-AES for 23 elements. Concentrations are 6-6300 mg kg(-1) As and 14-24800 mg kg(-1) Pb in soils, and 0.20-9 mg kg(-1) As and 2-195 mg Pb in vegetation. Trace element concentrations decrease rapidly away from the mine. with As and Pb concentrations in the range 6-1850 mg kg(-1) (median 22 mg kg(-1)) and 14-31 mg, kg(-1) (median 43 mg, kg(-1)), respectively, 1 km away from the mine. These concentrations are low when compared to other well-studied mining and smelting areas (e.g. 600 mg kg(-1) As at 8 km from Yellowknife smelter, Canada; >100 mg kg(-1) Pb over 270 km(2) around the Pb-Zn Port Pirie smelter. South Australia: mean of 1419 mg kg(-1) Pb around Aberystwyth smelter, Wales, UK). The high metal content of the vegetation and the low soil pH (mean pH 4.93) indicate the potential for trace element mobility which Could explain the relatively low concentration of metals in Tharsis topsoils and cause threats to plans to redevelop the Tharsis area as an orange plantation.

Remediation of soils contaminated with petrol and diesel with lime

Lime treatment of hydrocarbon-contaminated soils offers the potential to stabilize and solidify these materials, with a consequent reduction in the risks associated with the leachate emanating from them. This can aid the disposal of contaminated soils or enable their on-site treatment. In this study, the addition of hydrated lime and quicklime significantly reduced the leaching of total petroleum hydrocarbons (TPH) from soils polluted with a 50:50 petrol/diesel mixture. Treatment with quicklime was slightly more effective, but hydrated lime may be better in the field because of its ease of handling. It is proposed that this occurs as a consequence of pozzolanic reactions retaining the hydrocarbons within the soil matrix. There was some evidence that this may be a temporary effect, as leaching increased between seven and 21 days after treatment, but the TPH concentrations in the leachate of treated soils were still one order of magnitude below those of the control soil, offering significant protection to groundwater. The reduction in leaching following treatment was observed in both aliphatic and aromatic fractions, but the latter were more affected because of their higher solubilty. The results are discussed in the context of risk assessment, and recommendations for future research are made.

Fate of prions in soil: Detergent extraction of PrP from soils

The transmissible spongiform encephalopathies (TSEs) are caused by infectious agents whose structures have not been fully characterized but include abnormal forms of the host protein PrP, designated PrPSc, which are deposited in infected tissues. The transmission routes of scrapie and chronic wasting disease (CWD) seem to include environmental spread in their epidemiology, yet the fate of TSE agents in the environment is poorly understood. There are concerns that, for example, buried carcasses may remain a potential reservoir of infectivity for many years. Experimental determination of the environmental fate requires methods for assessing binding/elution of TSE infectivity, or its surrogate marker PrPSc, to and from materials with which it might interact. We report a method using Sarkosyl for the extraction of murine PrPSc, and its application to soils containing recombinant ovine PrP (recPrP). Elution properties suggest that PrP binds strongly to one or more soil components. Elution from a clay soil also required proteinase K digestion, suggesting that in the clay soil binding occurs via the N-terminal of PrP to a component that is absent from the sandy soils tested.

Impact of sewage sludge applications on the biogeochemistry of soils

This report describes an investigation into the bioavailability and fate of trace metals and their subsequent impact on important soil microbiological functions such as nitrification, denitrification and methane oxidation in low and high Cu containing soils in the presence and absence of residual organic matter from sewage sludge additions made 10 years earlier. The soils being studied are part of long term sewage sludge trials and include a low Cu soil ( 13.3mg Cu/ kg soil, 4.18 LOI %), left un- amended to serve as a control soil, soil amended with a high Cu sewage sludge ( 278.3mg Cu/ kg soil, 6.52 LOI %) and soil amended with a low Cu sewage sludge ( 46.3mg Cu/ kg soil, 6.18 LOI %). Soil was also amended with inorganic metal salts ( 273.4mg Cu/ kg soil, 4.52 LOI %) to further investigate the impact of Cu in the absence of additional organic matter contained in applied sewage sludge. Data from the first two years of a project are presented which has included field- based studies at long term sewage sludge trials based in Watlington, Oxford, UK and laboratory based studies at the Institute of Grassland & Environmental Research, North Wyke, Devon, UK.

A preliminary investigation into the use of ochre as a remedial amendment in arsenic-contaminated soils

Ochre is an unwanted waste product that accumulates in wetlands and streams draining abandoned coal and metal mines. A potential commercial use for ochre is to remediate As contaminated soil. Arsenic contaminated soil (605 mg kg(-1)) was mixed with different ochres (A, B and C) in a mass ratio of 1:1 and shaken in 20 mL of deionised water. After 72 h As concentration in solution was ca. 500 mu g kg(-1) in the control and 1-2.5 mu g kg(-1) in the ochre treated experiments. In a second experiment soil:ochre mixtures of 0.05-1:1 were shaken in 20 mL of deionised water for 24 h. For Ochres A and C, as Solution concentration was reduced to ca. 1 mu gkg(-1) by 0.2-1:1 ochre:soil mixtures. For Ochre B, as concentration only reached ca. 1 mu g kg(-1) in the 1:1 ochre:soil inix. Sorption of As was best modelled by a Freundlich isotherm using As sorption per mass of goethite in the ochre (log K= 1.64, n = 0.79, R-2 = 0.76, p <= 0.001). Efficiency of ochre in removing As from solution increased with increasing total Fe, goethite, citrate dithionite extractable Fe and surface area. (c) 2005 Elsevier Ltd. All rights reserved.

Edaphic influences on plant community adaptation in the Chiquibul forest of Belize

Edaphic variables figure significantly in plant community adaptations in tropical ecosystems but are often difficult to resolve because of the confounding influence of climate. Within the Chiquibul forest of Belize, large areas of Ultisols and Inceptisols occur juxtaposed within a larger zone of similar climate, permitting unambiguous assessment of edaphic contributions to forest composition. Wet chemical analyses, X-ray diffraction and X-ray fluorescence spectroscopy were employed to derive chemical (pH, exchangeable cations, CEC, total and organic C, total trace elements) and physical (texture, mineralogy) properties of four granite-derived Ustults from the Mountain Pine Ridge plateau and four limestone-derived Ustepts from the San Pastor region. The soils of these two regions support two distinct forests, each possessing a species composition reflecting the many contrasting physicochemical properties of the underlying soil. Within the Mountain Pine Ridge forest, species abundance and diversity is constrained by nutrient deficiencies and water-holding limitations imposed by the coarse textured, highly weathered Ultisols. As a consequence, the forest is highly adapted to seasonal drought, frequent fires and the significant input of atmospherically derived nutrients. The nutrient-rich Inceptisols of the San Pastor region, conversely, support an abundant and diverse evergreen forest, dominated by Sabal mauritiiformis, Cryosophila stauracantha and Manilkara spp. Moreover, the deep, fine textured soils in the depressions of the karstic San Pastor landscape collect and retain during the wet season much available water, thereby serving as refugia during particularly long periods of severe drought. To the extent that the soils of the Chiquibul region promote and maintain forest diversity, they also confer redundancy and resilience to these same forests and, to the broader ecosystem, of which they are a central part. (C) 2005 Elsevier B.V. All rights reserved.

Contributions of matric and osmotic potentials to the unfrozen water content of frozen soils

Recent reports show that biogeochemical processes continue when the soil is frozen, but are limited by water availability. However, there is little knowledge about the interactive effects of soil and environmental variables on amounts of unfrozen water in frozen soils. The aims of this study were to determine the contributions of matric and osmotic potentials to the unfrozen water content of frozen soil. We determined the effects of matric and osmotic potential on unfrozen water contents of frozen mineral soil fractions (ranging from coarse sand to fine silt) at -7 degrees C, and estimated the contributions of these potentials to liquid water contents in samples from organic surface layers of boreal soils frozen at -4 degrees C. In the mineral soil fractions the unfrozen water contents appeared to be governed solely by the osmotic potential, but in the humus layers of the sampled boreal soils both the osmotic and matric potentials control unfrozen water content, with osmotic potential contributing 20 to 69% of the total water potential. We also determined pore size equivalents, where unfrozen water resides at -4 degrees C, and found a strong correlation between these equivalents and microbial CO2 production. The larger the pores in which the unfrozen water is found the larger the microbial activity that can be sustained. The osmotic potential may therefore be a key determinant of unfrozen water and carbon dynamics in frozen soil. (C) 2008 Elsevier B.V. All rights reserved.

Zinc sorption in selected soils

The adsorption of nutrient elements is one of the most important solid- and liquid-phase interactions determining the retention and release of applied plant nutrients and the efficiency of fertilization. The study showed that the soils with high cation exchange capacity (CEC), CaCO3 , organic matter contents, and heavy texture adsorbed more zinc (Zn). The alkaline soils from Pakistan adsorbed more Zn than English acidic soils. Langmuir and Freundlich isotherm fit was excellent, and r(2) values for the Langmuir isotherm were highly significant (r(2) =0.84 to 0.99). The Langmuir b values, representing the adsorptive capacity of a soil, increased as the texture fineness increased in the soil, with increases in the concentration of adsorptive material (such as organic matter and CaCO3) and with increases in CEC and pH. The alkaline soils from Pakistan had higher bonding energy constant and higher log Kf values than the acidic English soils. Sequential extraction of Zn in these soils showed that most of the Zn was held in CaCO3 pool in the alkaline soils, whereas in acidic soils adsorbed Zn was in exchangeable form.

Assessment of the effect of time and temperature on the availability of residual phosphate in a glasshouse study of four soils using the Olsen method

The Olsen method is an indicator of plant-available phosphorus (P). The effect of time and temperature on residual phosphate in soils was measured using the Olsen method in a pot experiment. Four soils were investigated: two from Pakistan and one each from England (calcareous) and Colombia (acidic). Two levels of residual phosphate were developed in each soil after addition of phosphate by incubation at either 10degreesC or 45degreesC. The amount of phosphate added was based on the P maximum of each soil, calculated using the Langmuir equation. Rvegrass was used as the test crop. The pooled data for the four soils incubated at 10degreesC showed good correlation between Olsen P and dry matter yield or P uptake (r(2) = 0.85 and 0.77, respectively), whereas at 45 degreesC, each soil had its own relationship and pooled data did not show correlation of Olsen P with dry matter yield or P uptake. When the data at both temperatures were pooled, Olsen P was a good indicator of yield and uptake for the English soil. For the Pakistani soils, Olsen P after 45 degreesC treatment was an underestimate relative to the 10 degreesC data and for the Colombian soil it was an overestimate. The reasons for these differences need to be explored further before high temperature incubation can be used to simulate long-term changes in the field.

The role of gypsum in the reactions of phosphate with soils

The aim of this study was to examine the mechanisms by which gypsum increases the sorption of fertilizer-P in soils of and and semi-arid regions. Either gypsum or soil (Usher from the UK; pH 7.8, 7% organic matter, 21% CaCO3: Yasouj from Iran; pH 8.2, 1.4% OM, 18% CaCO3: Ghanimeh from Saudi Arabia; pH 7.8, 1% OM, 26% CaCO3, 13% gypsum) was shaken for 24 It with KH2PO4 solutions in 10 mM CaCl2. With gypsum, grinding increased sorption by a factor of about 3, and increase in pH from 5.6 to 7.5 greatly increased sorption. Scanning electron micrographs (SEM) and EDX quantitative analysis showed that small crystals of gypsum disappeared and roughly spherical particles of dicalcium phosphate (DCPD) were formed. Analysis of equilibrium Solutions showed, using GEOCHEM, that octa-calcium phosphate (OCP) coated the DCPD. For the soils, sorption was in the order Ghanimeh > Yasouj > Usher. Removal of gypsum from Ghanimeh reduced sorption, with precipitated gypsum having a greater effect than gypsum mixed physically with the soil. Addition to Usher had no effect. SEM and EDX could not be used in the soil matrix, but solubility analysis again showed that solutions were close to equilibrium with OCP. Usher was unresponsive to added gypsum, presumably because of its small sorption capacity and high organic matter content. In Ghanimeh and Yasouj soils, gypsum increased sorption by being a source of readily available Ca2+ (c) 2005 Elsevier B.V. All rights reserved.

The importance of precision in sampling sludges, biowastes and treated soils in a regulatory framework

As part of the European Commission (EC)'s revision of the Sewage Sludge Directive and the development of a Biowaste Directive, there was recognition of the difficulty of comparing data from Member States (MSs) because of differences in sampling and analytical procedures. The 'HORIZONTAL' initiative, funded by the EC and MSs, seeks to address these differences in approach and to produce standardised procedures in the form of CEN standards. This article is a preliminary investigation into aspects of the sampling of biosolids, composts and soils to which there is a history of biosolid application. The article provides information on the measurement uncertainty associated with sampling from heaps, large bags and pipes and soils in the landscape under a limited set of conditions, using sampling approaches in space and time and sample numbers based on procedures widely used in the relevant industries and when sampling similar materials. These preliminary results suggest that considerably more information is required before the appropriate sample design, optimum number of samples, number of samples comprising a composite, and temporal and spatial frequency of sampling might be recommended to achieve consistent results of a high level of precision and confidence. (C) 2004 Elsevier Ltd. All rights reserved.