Genetic variation of and environmental effects on inducibility of resistance in tomatoes (Solanum lycopersicum L.) to Phytophthora infestans (Mont) de Bary

Many plant strengtheners are promoted for their supposed effects on nutrient uptake and/or resistance induction (IR). In addition, many organic fertilizers are supposed to enhance plant health and several studies have shown that tomatoes grown organically are more resistant to late blight, caused by Phytophthora infestans to tomatoes grown conventionally. Much is known about the mechanisms underlying IR. In contrast, there is no systematic knowledge about genetic variation for IR. Therefore, the following questions were addressed in the presented dissertation: (i) Is there genetic variation among tomato genotypes for inducibility of resistance to P. infestans? (ii) How do different PS compare with the chemical inducer BABA in their ability to IR? (iii) Does IR interact with the inducer used and different organic fertilizers? A varietal screening showed that contrary to the commonly held belief IR in tomatoes is genotype and isolate specific. These results indicate that it should be possible to select for inducibility of resistance in tomato breeding. However, isolate specificity also suggests that there could be pathogen adaptation. The three tested PS as well as two of the three tested organic fertilisers all induced resistance in the tomatoes. Depending on PS or BABA variety and isolate effects varied. In contrast, there were no variety and isolate specific effects of the fertilisers and no interactions with the PS and fertilisers. This suggests that the different PS should work independent of the soil substrate used. In contrast the results were markedly different when isolate mixtures were used for challenge inoculations. Plants were generally less susceptible to isolate mixtures than to single isolates. In addition, the effectiveness of the PS was greater and more similar to BABA when isolate mixtures were used. The fact that the different PS and BABA differed in their ability to induce resistance in different host genotype -pathogen isolate combinations puts the usefulness of IR as a breeding goal in question. This would result in varieties depending on specific inducers. The results with the isolate mixtures are highly relevant. On the one hand they increase the effectiveness of the resistance inducers. On the other hand, measures that increase the pathogen diversity such as the use of diversified host populations will also increase the overall resistance of the hosts. For organic tomato production the results indicate that it is possible to enhance the tomato growing system with respect to plant health management by using optimal fertilisers, plant strengtheners and any measures that increase system diversity.

Utilisation of Giant African snail (Achatina fulica) meal as protein source by laying hens

A 12-week experiment was carried out to investigate the effects of substituting Giant African snail meal for fish meal in laying hens diet. Four diets were formulated to contain snail meal as replacement for fish meal at 0 (control), 33, 67 and 100%. A total of 120 Shaver Brown pullets aged 18 weeks were allocated to the dietary treatments in a randomised design. Each treatment consisted of three replicates and ten birds per replicate. Feed intake increased only for the 33% treatment as compared to the 67% replacement diet but did not differ from the other treatments. There were no significant treatment effects on egg performance parameters observed (egg production, egg weight, total egg mass, feed conversion ratio and percent shell). The overall feed cost of egg production reduced on the snail meal-based diets. The organoleptic evaluation of boiled eggs revealed no difference between the treatments. Based on these results it was concluded that total replacement of fish meal with cooked snail meat meal does not compromise laying performance or egg quality. The substitution is beneficial in terms of production cost reduction and the reduction of snails will have a beneficial impact especially where these snails are a serious agricultural pest. The manual collection and processing of snails can also become a source of rural income.

Experimental and modeling studies of forced convection storage and drying systems for sweet potatoes

Sweet potato is an important strategic agricultural crop grown in many countries around the world. The roots and aerial vine components of the crop are used for both human consumption and, to some extent as a cheap source of animal feed. In spite of its economic value and growing contribution to health and nutrition, harvested sweet potato roots and aerial vine components has limited shelf-life and is easily susceptible to post-harvest losses. Although post-harvest losses of both sweet potato roots and aerial vine components is significant, there is no information available that will support the design and development of appropriate storage and preservation systems. In this context, the present study was initiated to improve scientific knowledge about sweet potato post-harvest handling. Additionally, the study also seeks to develop a PV ventilated mud storehouse for storage of sweet potato roots under tropical conditions. In study one, airflow resistance of sweet potato aerial vine components was investigated. The influence of different operating parameters such as airflow rate, moisture content and bulk depth at different levels on airflow resistance was analyzed. All the operating parameters were observed to have significant (P < 0.01) effect on airflow resistance. Prediction models were developed and were found to adequately describe the experimental pressure drop data. In study two, the resistance of airflow through unwashed and clean sweet potato roots was investigated. The effect of sweet potato roots shape factor, surface roughness, orientation to airflow, and presence of soil fraction on airflow resistance was also assessed. The pressure drop through unwashed and clean sweet potato roots was observed to increase with higher airflow, bed depth, root grade composition, and presence of soil fraction. The physical properties of the roots were incorporated into a modified Ergun model and compared with a modified Shedd’s model. The modified Ergun model provided the best fit to the experimental data when compared with the modified Shedd’s model. In study three, the effect of sweet potato root size (medium and large), different air velocity and temperature on the cooling/or heating rate and time of individual sweet potato roots were investigated. Also, a simulation model which is based on the fundamental solution of the transient equations was proposed for estimating the cooling and heating time at the centre of sweet potato roots. The results showed that increasing air velocity during cooling and heating significantly (P < 0.05) affects the cooling and heating times. Furthermore, the cooling and heating times were significantly different (P < 0.05) among medium and large size sweet potato roots. Comparison of the simulation results with experimental data confirmed that the transient simulation model can be used to accurately estimate the cooling and heating times of whole sweet potato roots under forced convection conditions. In study four, the performance of charcoal evaporative cooling pad configurations for integration into sweet potato roots storage systems was investigated. The experiments were carried out at different levels of air velocity, water flow rates, and three pad configurations: single layer pad (SLP), double layers pad (DLP) and triple layers pad (TLP) made out of small and large size charcoal particles. The results showed that higher air velocity has tremendous effect on pressure drop. Increasing the water flow rate above the range tested had no practical benefits in terms of cooling. It was observed that DLP and TLD configurations with larger wet surface area for both types of pads provided high cooling efficiencies. In study five, CFD technique in the ANSYS Fluent software was used to simulate airflow distribution in a low-cost mud storehouse. By theoretically investigating different geometries of air inlet, plenum chamber, and outlet as well as its placement using ANSYS Fluent software, an acceptable geometry with uniform air distribution was selected and constructed. Experimental measurements validated the selected design. In study six, the performance of the developed PV ventilated system was investigated. Field measurements showed satisfactory results of the directly coupled PV ventilated system. Furthermore, the option of integrating a low-cost evaporative cooling system into the mud storage structure was also investigated. The results showed a reduction of ambient temperature inside the mud storehouse while relative humidity was enhanced. The ability of the developed storage system to provide and maintain airflow, temperature and relative humidity which are the key parameters for shelf-life extension of sweet potato roots highlight its ability to reduce post-harvest losses at the farmer level, particularly under tropical climate conditions.