Lithography-free micro- and nanostructuring based on conventional plasma etching

In now-a-days semiconductor and MEMS technologies the photolithography is the working horse for fabrication of functional devices. The conventional way (so called Top-Down approach) of microstructuring starts with photolithography, followed by patterning the structures using etching, especially dry etching. The requirements for smaller and hence faster devices lead to decrease of the feature size to the range of several nanometers. However, the production of devices in this scale range needs photolithography equipment, which must overcome the diffraction limit. Therefore, new photolithography techniques have been recently developed, but they are rather expensive and restricted to plane surfaces. Recently a new route has been presented - so-called Bottom-Up approach - where from a single atom or a molecule it is possible to obtain functional devices. This creates new field - Nanotechnology - where one speaks about structures with dimensions 1 - 100 nm, and which has the possibility to replace the conventional photolithography concerning its integral part - the self-assembly. However, this technique requires additional and special equipment and therefore is not yet widely applicable. This work presents a general scheme for the fabrication of silicon and silicon dioxide structures with lateral dimensions of less than 100 nm that avoids high-resolution photolithography processes. For the self-aligned formation of extremely small openings in silicon dioxide layers at in depth sharpened surface structures, the angle dependent etching rate distribution of silicon dioxide against plasma etching with a fluorocarbon gas (CHF3) was exploited. Subsequent anisotropic plasma etching of the silicon substrate material through the perforated silicon dioxide masking layer results in high aspect ratio trenches of approximately the same lateral dimensions. The latter can be reduced and precisely adjusted between 0 and 200 nm by thermal oxidation of the silicon structures owing to the volume expansion of silicon during the oxidation. On the basis of this a technology for the fabrication of SNOM calibration standards is presented. Additionally so-formed trenches were used as a template for CVD deposition of diamond resulting in high aspect ratio diamond knife. A lithography-free method for production of periodic and nonperiodic surface structures using the angular dependence of the etching rate is also presented. It combines the self-assembly of masking particles with the conventional plasma etching techniques known from microelectromechanical system technology. The method is generally applicable to bulk as well as layered materials. In this work, layers of glass spheres of different diameters were assembled on the sample surface forming a mask against plasma etching. Silicon surface structures with periodicity of 500 nm and feature dimensions of 20 nm were produced in this way. Thermal oxidation of the so structured silicon substrate offers the capability to vary the fill factor of the periodic structure owing to the volume expansion during oxidation but also to define silicon dioxide surface structures by selective plasma etching. Similar structures can be simply obtained by structuring silicon dioxide layers on silicon. The method offers a simple route for bridging the Nano- and Microtechnology and moreover, an uncomplicated way for photonic crystal fabrication.

Spontane Strukturbildung in Mehrschichtsystemen unter Verwendung Molekularer Gläser

Den Schwerpunkt dieser Dissertation bildet zum einen die Entwicklung eines theoretischen Modells zur Beschreibung des Strukturbildungsprozesses in organisch/anorganischen Doppelschichtsystemen und zum anderen die Untersuchung der Übertragbarkeit dieser theoretisch gewonnenen Ergebnisse auf reale Systeme. Hierzu dienen systematische experimentelle Untersuchungen dieses Phänomens an einem Testsystem. Der Bereich der selbstorganisierenden Systeme ist von hohem wissenschaftlichen Interesse, erlaubt er doch die Realisierung von Strukturen, die nicht den Begrenzungen heutiger Techniken unterliegen, wie etwa der Beugung bei lithographischen Verfahren. Darüber hinaus liefert ein vertieftes Verständnis des Strukturbildungsprozesses auch eine Möglichkeit, im Falle entsprechender technischer Anwendungen Instabilitäten innerhalb der Schichtsysteme zu verhindern und somit einer Degradation der Bauteile entgegenzuwirken. Im theoretischen Teil der Arbeit konnte ein Modell im Rahmen der klassischen Elastizitätstheorie entwickelt werden, mit dessen Hilfe sich die Entstehung der Strukturen in Doppelschichtsystemen verstehen läßt. Der hier gefundene funktionale Zusammenhang zwischen der Periode der Strukturen und dem Verhältnis der Schichtdicken von organischer und anorganischer Schicht, wird durch die experimentellen Ergebnisse sehr gut bestätigt. Die Ergebnisse zeigen, daß es technologisch möglich ist, über die Vorgabe der Schichtdicke in einem Materialsystem die Periodizität der entstehenden Strukturen vorzugeben. Darüber hinaus liefert das vorgestellte Modell eine Stabilitätsbedingung für die Schichtsysteme, die es ermöglicht, zu jedem Zeitpunkt die dominierende Mode zu identifizieren. Ein Schwerpunkt der experimentellen Untersuchungen dieser Arbeit liegt auf der Strukturbildung innerhalb der Schichtsysteme. Das Testsystem wurde durch Aufbringen einer organischen Schicht - eines sog. Molekularen Glases - auf ein Glassubstrat realisiert, als Deckschicht diente eine Siliziumnitrid-Schicht. Es wurden Proben mit variierenden Schichtdicken kontrolliert erwärmt. Sobald die Temperatur des Schichtsystems in der Größenordnung der Glasübergangstemperatur des jeweiligen organischen Materials lag, fand spontan eine Strukturbildung auf Grund einer Spannungsrelaxation statt. Es ließen sich durch die Wahl einer entsprechenden Heizquelle unterschiedliche Strukturen realisieren. Bei Verwendung eines gepulsten Lasers, also einer kreisförmigen Wärmequelle, ordneten sich die Strukturen konzentrisch an, wohingegen sich ihre Ausrichtung bei Verwendung einer flächenhaften Heizplatte statistisch verteilte. Auffällig bei allen Strukturen war eine starke Modulation der Oberfläche. Ferner konnte in der Arbeit gezeigt werden, daß sich durch eine gezielte Veränderung der Spannungsverteilung innerhalb der Schichtsysteme die Ausrichtung der Strukturen (gezielt) manipulieren ließen. Unabhängig davon erlaubte die Variation der Schichtdicken die Realisierung von Strukturen mit einer Periodizität im Bereich von einigen µm bis hinunter zu etwa 200 nm. Die Kontrolle über die Ausrichtung und die Periodizität ist Grundvoraussetzung für eine zukünftige technologische Nutzung des Effektes zur kontrollierten Herstellung von Mikro- bzw. Nanostrukturen. Darüber hinaus konnte ein zunächst von der Strukturbildung unabhängiges Konzept eines aktiven Sensors für die optische Raster-Nahfeld-Mikroskopie vorgestellt werden, das das oben beschriebene System, bestehend aus einem fluoreszierenden Molekularen Glas und einer Siliziumnitrid-Deckschicht, verwendet. Erste theoretische und experimentelle Ergebnisse zeigen das technologische Potential dieses Sensortyps.

Organic field-effect transistors and phototransistors based on amorphous materials

A comparison between the charge transport properties in low molecular amorphous thin films of spiro-linked compound and their corresponding parent compound has been demonstrated. The field-effect transistor method is used for extracting physical parameters such as field-effect mobility of charge carriers, ON/OFF ratios, and stability. In addition, phototransistors have been fabricated and demonstrated for the first time by using organic materials. In this case, asymmetrically spiro-linked compounds are used as active materials. The active materials used in this study can be divided into three classes, namely Spiro-linked compounds (symmetrically spiro-linked compounds), the corresponding parent-compounds, and photosensitive spiro-linked compounds (asymmetrically spiro-linked com-pounds). Some of symmetrically spiro-linked compounds used in this study were 2,2',7,7'-Tetrakis-(di-phenylamino)-9,9'-spirobifluorene (Spiro-TAD),2,2',7,7'-Tetrakis-(N,N'-di-p-methylphenylamino)-9,9'-spirobifluorene (Spiro-TTB), 2,2',7,7'-Tetra-(m-tolyl-phenylamino)-9,9'-spirobifluorene (Spiro-TPD), and 2,2Ž,7,7Ž-Tetra-(N-phenyl-1-naphtylamine)-9,9Ž-spirobifluorene (Spiro alpha-NPB). Related parent compounds of the symmetrically spiro-linked compound used in this study were N,N,N',N'-Tetraphenylbenzidine (TAD), N,N,N',N'-Tetrakis(4-methylphenyl)benzidine (TTB), N,N'-Bis(3-methylphenyl)-(1,1'-biphenyl)-4,4'-diamine (TPD), and N,N'-Diphenyl-N,N'-bis(1-naphthyl)-1,1'-biphenyl-4,4'-diamine (alpha-NPB). The photosensitive asymmetrically spiro-linked compounds used in this study were 2,7-bis-(N,N'-diphenylamino)-2',7'-bis(biphenyl-4-yl)-9,9'-spirobifluorene (Spiro-DPSP), and 2,7-bis-(N,N'-diphenylamino)-2',7'-bis(spirobifluorene-2-yl)-9,9'-spirobifluorene (Spiro-DPSP^2). It was found that the field-effect mobilities of charge carriers in thin films of symmetrically spiro-linked compounds and their corresponding parent compounds are in the same order of magnitude (~10^-5 cm^2/Vs). However, the thin films of the parent compounds were easily crystallized after the samples have been exposed in ambient atmosphere and at room temperature for three days. In contrast, the thin films and the transistor characteristics of symmetrically spiro-linked compound did not change significantly after the samples have been stored in ambient atmosphere and at room temperature for several months. Furthermore, temperature dependence of the mobility was analyzed in two models, namely the Arrhenius model and the Gaussian Disorder model. The Arrhenius model tends to give a high value of the prefactor mobility. However, it is difficult to distinguish whether the temperature behaviors of the material under consideration follows the Arrhenius model or the Gaussian Disorder model due to the narrow accessible range of the temperatures. For the first time, phototransistors have been fabricated and demonstrated by using organic materials. In this case, asymmetrically spiro-linked compounds are used as active materials. Intramolecular charge transfer between a bis(diphenylamino)biphenyl unit and a sexiphenyl unit leads to an increase in charge carrier density, providing the amplification effect. The operational responsivity of better than 1 A/W can be obtained for ultraviolet light at 370 nm, making the device interesting for sensor applications. This result offers a new potential application of organic thin film phototransistors as low-light level and low-cost visible blind ultraviolet photodetectors.

High-Speed Semiconductor Lasers based on Low-Dimensional Active Materials for Optical Telecommunication

The scope of this work is the fundamental growth, tailoring and characterization of self-organized indium arsenide quantum dots (QDs) and their exploitation as active region for diode lasers emitting in the 1.55 µm range. This wavelength regime is especially interesting for long-haul telecommunications as optical fibers made from silica glass have the lowest optical absorption. Molecular Beam Epitaxy is utilized as fabrication technique for the quantum dots and laser structures. The results presented in this thesis depict the first experimental work for which this reactor was used at the University of Kassel. Most research in the field of self-organized quantum dots has been conducted in the InAs/GaAs material system. It can be seen as the model system of self-organized quantum dots, but is not suitable for the targeted emission wavelength. Light emission from this system at 1.55 µm is hard to accomplish. To stay as close as possible to existing processing technology, the In(AlGa)As/InP (100) material system is deployed. Depending on the epitaxial growth technique and growth parameters this system has the drawback of producing a wide range of nano species besides quantum dots. Best known are the elongated quantum dashes (QDash). Such structures are preferentially formed, if InAs is deposited on InP. This is related to the low lattice-mismatch of 3.2 %, which is less than half of the value in the InAs/GaAs system. The task of creating round-shaped and uniform QDs is rendered more complex considering exchange effects of arsenic and phosphorus as well as anisotropic effects on the surface that do not need to be dealt with in the InAs/GaAs case. While QDash structures haven been studied fundamentally as well as in laser structures, they do not represent the theoretical ideal case of a zero-dimensional material. Creating round-shaped quantum dots on the InP(100) substrate remains a challenging task. Details of the self-organization process are still unknown and the formation of the QDs is not fully understood yet. In the course of the experimental work a novel growth concept was discovered and analyzed that eases the fabrication of QDs. It is based on different crystal growth and ad-atom diffusion processes under supply of different modifications of the arsenic atmosphere in the MBE reactor. The reactor is equipped with special valved cracking effusion cells for arsenic and phosphorus. It represents an all-solid source configuration that does not rely on toxic gas supply. The cracking effusion cell are able to create different species of arsenic and phosphorus. This constitutes the basis of the growth concept. With this method round-shaped QD ensembles with superior optical properties and record-low photoluminescence linewidth were achieved. By systematically varying the growth parameters and working out a detailed analysis of the experimental data a range of parameter values, for which the formation of QDs is favored, was found. A qualitative explanation of the formation characteristics based on the surface migration of In ad-atoms is developed. Such tailored QDs are finally implemented as active region in a self-designed diode laser structure. A basic characterization of the static and temperature-dependent properties was carried out. The QD lasers exceed a reference quantum well laser in terms of inversion conditions and temperature-dependent characteristics. Pulsed output powers of several hundred milli watt were measured at room temperature. In particular, the lasers feature a high modal gain that even allowed cw-emission at room temperature of a processed ridge wave guide device as short as 340 µm with output powers of 17 mW. Modulation experiments performed at the Israel Institute of Technology (Technion) showed a complex behavior of the QDs in the laser cavity. Despite the fact that the laser structure is not fully optimized for a high-speed device, data transmission capabilities of 15 Gb/s combined with low noise were achieved. To the best of the author`s knowledge, this renders the lasers the fastest QD devices operating at 1.55 µm. The thesis starts with an introductory chapter that pronounces the advantages of optical fiber communication in general. Chapter 2 will introduce the fundamental knowledge that is necessary to understand the importance of the active region`s dimensions for the performance of a diode laser. The novel growth concept and its experimental analysis are presented in chapter 3. Chapter 4 finally contains the work on diode lasers.

Optical Characterization of Organic Gain Materials for UV-emitting Hybrid Complex Coupled VCSELs

In this thesis, optical gain measurement setup based on variable stripe length method is designed, implemented and improved. The setup is characterized using inorganic and organic samples. The optical gain of spiro-quaterphenyl is calculated and compared with measurements from the setup. Films with various thicknesses of spiro-quaterphenyl, methoxy-spiro-quaterphenyl and phenoxy-spiro-quaterphenyl are deposited by a vacuum vapor deposition technique forming asymmetric slab waveguides. The optical properties, laser emission threshold, optical gain and loss coefficient for these films are measured. Additionally, the photodegradation during pumping process is investigated.