Piezoresistive cantilevers with an integrated bimorph actuator

Scanning Probe Microscopy (SPM) has become of fundamental importance for research in area of micro and nano-technology. The continuous progress in these fields requires ultra sensitive measurements at high speed. The imaging speed limitation of the conventional Tapping Mode SPM is due to the actuation time constant of piezotube feedback loop that keeps the tapping amplitude constant. In order to avoid this limit a deflection sensor and an actuator have to be integrated into the cantilever. In this work has been demonstrated the possibility of realisation of piezoresistive cantilever with an embedded actuator. Piezoresistive detection provides a good alternative to the usual optical laser beam deflection technique. In frames of this thesis has been investigated and modelled the piezoresistive effect in bulk silicon (3D case) for both n- and p-type silicon. Moving towards ultra-sensitive measurements it is necessary to realize ultra-thin piezoresistors, which are well localized to the surface, where the stress magnitude is maximal. New physical effects such as quantum confinement which arise due to the scaling of the piezoresistor thickness was taken into account in order to model the piezoresistive effect and its modification in case of ultra-thin piezoresistor (2D case). The two-dimension character of the electron gas in n-type piezoresistors lead up to decreasing of the piezoresistive coefficients with increasing the degree of electron localisation. Moreover for p-type piezoresistors the predicted values of the piezoresistive coefficients are higher in case of localised holes. Additionally, to the integration of the piezoresistive sensor, actuator integrated into the cantilever is considered as fundamental for realisation of fast SPM imaging. Actuation of the beam is achieved thermally by relying on differences in the coefficients of thermal expansion between aluminum and silicon. In addition the aluminum layer forms the heating micro-resistor, which is able to accept heating impulses with frequency up to one megahertz. Such direct oscillating thermally driven bimorph actuator was studied also with respect to the bimorph actuator efficiency. Higher eigenmodes of the cantilever are used in order to increase the operating frequencies. As a result the scanning speed has been increased due to the decreasing of the actuation time constant. The fundamental limits to force sensitivity that are imposed by piezoresistive deflection sensing technique have been discussed. For imaging in ambient conditions the force sensitivity is limited by the thermo-mechanical cantilever noise. Additional noise sources, connected with the piezoresistive detection are negligible.

Der Einfluss von Ankern auf Verkaufsergebnisse in telefonischen Verkaufsgesprächen

Numerische Urteile wie Schätzungen oder Prognosen sind anfällig für Ankereffekte. Ein in eine Entscheidungssituation willkürlich eingeführter numerischer Wert – der Anker – beeinflusst oft das Urteil im Sinne einer Assimilation des Urteils an diesen Wert. Bei Kaufentscheidungen fließt das Ergebnis eines Vergleichs des Produktpreises mit einem Referenzpreis, einem numerischen Wert, in die Kaufentscheidung mit ein. Unter Orientierung an die Prospekttheorie von Kahneman & Tversky kann dieser Referenzpreis in Form eines implementierten Ankers variiert werden. Die vorgelegte interdisziplinäre Arbeit wendet psychologisches Fachwissen in den Wirtschaftswissenschaften an. Sie beschäftigt sich mit den Möglichkeiten bei telefonischen Verkaufsgesprächen, gezielt Anker zu Erhöhung der Verkaufsquote einzusetzen. Der Anker wird in drei unterschiedlichen Experimenten entweder durch den Preis eines zusätzlich angebotenen Produkts, durch das Einbringen eines belanglos scheinenden numerischen Wertes, wie die Anzahl an bereits getätigten Anrufen, oder in Form einer Schätzfrage in das Verkaufsgespräch implementiert. Es wird dabei festgestellt, dass durch einen im Vergleich zum verkaufenden Produkt höheren numerischen Wert, dem Anker, die Verkaufsquote erhöht werden kann. Das Neuartige an der Arbeit liegt vor allem im Aufzeigen der Einfachheit solcher ökonomisch effektiver Ankersetzungen in Verkaufsgesprächen. Willkürlich in eine Kaufsituation eingeführte numerische Werte können - analog zu ihrem Einfluss in Urteilssituationen - auch Kaufentscheidungen in einem realen Markt beeinflussen.

Bildbasierte Authentifizierung und Verschlüsselung

Bildbasierte Authentifizierung und Verschlüsselung: Identitätsbasierte Kryptographie (oft auch identity Based Encryption, IBE) ist eine Variation der asymmetrischen Schlüsselverfahren, bei der der öffentliche Schlüssel des Anwenders eine beliebig wählbare Zeichenfolge sein darf, die dem Besitzer offensichtlich zugeordnet werden kann. Adi Shamir stellte 1984 zunächst ein solches Signatursystem vor. In der Literatur wird dabei als öffentlicher Schlüssel meist die Email-Adresse oder eine Sozialversicherungsnummer genannt. Der Preis für die freie Schlüsselwahl ist die Einbeziehung eines vertrauenswürdigen Dritten, genannt Private Key Generator, der mit seinem privaten Generalschlüssel den privaten Schlüssel des Antragstellers generiert. Mit der Arbeit von Boneh und Franklin 2001 zum Einsatz der Weil-Paarbildung über elliptischen Kurven wurde IBE auf eine sichere und praktikable Grundlage gestellt. In dieser Arbeit wird nach einer allgemeinen Übersicht über Probleme und Lösungsmöglichkeiten für Authentifizierungsaufgaben im zweiten Teil als neue Idee der Einsatz eines Bildes des Anwenders als öffentlicher Schlüssel vorgeschlagen. Dazu wird der Ablauf der Schlüsselausgabe, die Bestellung einer Dienstleistung, z. B. die Ausstellung einer personengebundenen Fahrkarte, sowie deren Kontrolle dargestellt. Letztere kann offline auf dem Gerät des Kontrolleurs erfolgen, wobei Ticket und Bild auf dem Handy des Kunden bereitliegen. Insgesamt eröffnet sich dadurch die Möglichkeit einer Authentifizierung ohne weitere Preisgabe einer Identität, wenn man davon ausgeht, dass das Bild einer Person angesichts allgegenwärtiger Kameras sowieso öffentlich ist. Die Praktikabilität wird mit einer Implementierung auf der Basis des IBE-JCA Providers der National University of Ireland in Maynooth demonstriert und liefert auch Aufschluss auf das in der Praxis zu erwartende Laufzeitverhalten.

Fliesslochformen und Gewindefurchen in dünne Bleche und Rohre aus Kupfer und Kupferlegierungen

This thesis in Thermal Flow Drilling and Flowtap in thin metal sheet and pipes of copper and copper alloys had as objectives to know the comportment of copper and copper alloys sheet metal during the Thermal Flow Drill processes with normal tools, to know the best Speed and Feed machine data for the best bushing quality, to known the best Speed for Form Tapping processes and to know the best bush long in pure copper pipes for water solar interchange equipment. Thermal Flow Drilling (TFD) and Form Tapping (FT) is one of the research lines of the Institute of Production and Logistics (IPL) at University of Kassel. At December 1995, a work meeting of IPL, Santa Catarina University, Brazil, Buenos Aires University, Argentine, Tarapacá University (UTA), Chile members and the CEO of Flowdrill B.V. was held in Brazil. The group decided that the Manufacturing Laboratory (ML) of UTA would work with pure copper and brass alloys sheet metal and pure copper pipes in order to develop a water interchange solar heater. The Flowdrill BV Company sent tools to Tarapacá University in 1996. In 1999 IPL and the ML carried out an ALECHILE research project promoted by the DAAD and CONICyT in copper sheet metal and copper pipes and sheet metal a-brass alloys. The normal tools are lobed, conical tungsten carbide tool. When rotated at high speed and pressed with high axial force into sheet metal or thin walled tube generated heat softens the metal and allows the drill to feed forward produce a hole and simultaneously form a bushing from the displacement material. In the market exist many features but in this thesis is used short and longs normal tools of TFD. For reach the objectives it was takes as references four qualities of the frayed end bushing, where the best one is the quality class I. It was used pure copper and a-brass alloys sheet metals, with different thickness. It was used different TFD drills diameter for four thread type, from M-5 to M10. Similar to the Aluminium sheet metals studies it was used the predrilling processes with HSS drills around 30% of the TFD diameter (1,5 – 3,0 mm D). In the next step is used only 2,0 mm thick metal sheet, and 9,2 mm TFD diameter for M-10 thread. For the case of pure commercial copper pipes is used for ¾” inch diameter and 12, 8 mm (3/8”) TFD drill for holes for 3/8” pipes and different normal HSS drills for predrilling processes. The chemical sheet metal characteristics were takes as reference for the material behaviour. The Chilean pure copper have 99,35% of Cu and 0,163% of Zinc and the Chilean a-brass alloys have 75,6% of Cu and 24,0% of Zinc. It is used two German a-brass alloys; Nº1 have 61,6% of Cu, 36,03 % of Zinc and 2,2% of Pb and the German a-brass alloys Nº2 have 63,1% of Cu, 36,7% of Zinc and 0% of Pb. The equipments used were a HAAS CNC milling machine centre, a Kistler dynamometer, PC Pentium II, Acquisition card, TESTPOINT and XAct software, 3D measurement machine, micro hardness, universal test machine, and metallographic microscope. During the test is obtained the feed force and momentum curves that shows the material behaviour with TFD processes. In general it is take three phases. It was possible obtain the best machining data for the different sheet of copper and a-brass alloys thick of Chilean materials and bush quality class I. In the case of a-brass alloys, the chemical components and the TFD processes temperature have big influence. The temperature reach to 400º Celsius during the TFD processes and the a-brass alloys have some percents of Zinc the bush quality is class I. But when the a-brass alloys have some percents of Lead who have 200º C melting point is not possible to obtain a bush, because the Lead gasify and the metallographic net broke. During the TFD processes the recrystallization structures occur around the Copper and a-brass alloy bush, who gives more hardness in these zones. When the threads were produce with Form Tapping processes with Flowtap tools, this hardness amount gives a high limit load of the thread when hey are tested in a special support that was developed for it. For eliminated the predrilling processes with normal HSS drills it was developed a compound tool. With this new tool it was possible obtain the best machining data for quality class I bush. For the copper pipes it is made bush without predrilling and the quality class IV was obtained. When it is was used predrilling processes, quality classes I bush were obtained. Then with different HSS drill diameter were obtained different long bush, where were soldering with four types soldering materials between pipes with 3/8” in a big one as ¾”. Those soldering unions were tested by traction test and all the 3/8” pipes broken, and the soldering zone doesn’t have any problem. Finally were developed different solar water interchange heaters and tested. As conclusions, the present Thesis shows that the Thermal Flow Drilling in thinner metal sheets of cooper and cooper alloys needs a predrilling process for frayed end quality class I bushings, similar to thinner sheets of aluminium bushes. The compound tool developed could obtain quality class I bushings and excludes predrilling processes. The bush recrystalization, product of the friction between the tool and the material, the hardness grows and it is advantageous for the Form Tapping. The methodology developed for commercial copper pipes permits to built water solar interchange heaters.