Modelling and simulation of a photovoltaic fuel cell hybrid system

A stand-alone power system is an autonomous system that supplies electricity to the user load without being connected to the electric grid. This kind of decentralized system is frequently located in remote and inaccessible areas. It is essential for about one third of the world population which are living in developed or isolated regions and have no access to an electricity utility grid. The most people live in remote and rural areas, with low population density, lacking even the basic infrastructure. The utility grid extension to these locations is not a cost effective option and sometimes technically not feasible. The purpose of this thesis is the modelling and simulation of a stand-alone hybrid power system, referred to as “hydrogen Photovoltaic-Fuel Cell (PVFC) hybrid system”. It couples a photovoltaic generator (PV), an alkaline water electrolyser, a storage gas tank, a proton exchange membrane fuel cell (PEMFC), and power conditioning units (PCU) to give different system topologies. The system is intended to be an environmentally friendly solution since it tries maximising the use of a renewable energy source. Electricity is produced by a PV generator to meet the requirements of a user load. Whenever there is enough solar radiation, the user load can be powered totally by the PV electricity. During periods of low solar radiation, auxiliary electricity is required. An alkaline high pressure water electrolyser is powered by the excess energy from the PV generator to produce hydrogen and oxygen at a pressure of maximum 30bar. Gases are stored without compression for short- (hourly or daily) and long- (seasonal) term. A proton exchange membrane (PEM) fuel cell is used to keep the system’s reliability at the same level as for the conventional system while decreasing the environmental impact of the whole system. The PEM fuel cell consumes gases which are produced by an electrolyser to meet the user load demand when the PV generator energy is deficient, so that it works as an auxiliary generator. Power conditioning units are appropriate for the conversion and dispatch the energy between the components of the system. No batteries are used in this system since they represent the weakest when used in PV systems due to their need for sophisticated control and their short lifetime. The model library, ISET Alternative Power Library (ISET-APL), is designed by the Institute of Solar Energy supply Technology (ISET) and used for the simulation of the hybrid system. The physical, analytical and/or empirical equations of each component are programmed and implemented separately in this library for the simulation software program Simplorer by C++ language. The model parameters are derived from manufacturer’s performance data sheets or measurements obtained from literature. The identification and validation of the major hydrogen PVFC hybrid system component models are evaluated according to the measured data of the components, from the manufacturer’s data sheet or from actual system operation. Then, the overall system is simulated, at intervals of one hour each, by using solar radiation as the primary energy input and hydrogen as energy storage for one year operation. A comparison between different topologies, such as DC or AC coupled systems, is carried out on the basis of energy point of view at two locations with different geographical latitudes, in Kassel/Germany (Europe) and in Cairo/Egypt (North Africa). The main conclusion in this work is that the simulation method of the system study under different conditions could successfully be used to give good visualization and comparison between those topologies for the overall performance of the system. The operational performance of the system is not only depending on component efficiency but also on system design and consumption behaviour. The worst case of this system is the low efficiency of the storage subsystem made of the electrolyser, the gas storage tank, and the fuel cell as it is around 25-34% at Cairo and 29-37% at Kassel. Therefore, the research for this system should be concentrated in the subsystem components development especially the fuel cell.

Economic evaluation of proposed pure and mixed stands in Central Vietnam highlands

In comparison with mixed forest stands, the cultivation of pure plantations in Vietnam entails serious ecological consequences such as loss of biodiversity and higher rate of soil erosion. The economic evaluation is elaborated between pure plantations and mixed forests where the fast-growing tree species are mixed with slow growing tree species which are planted in stripes separating the segments with fast-growing tree species (Acacia sp.). For the evaluation, the input values were used from local costs of goods, services and labour. The results show that the internal rate of return is the highest in the case of pure plantation in comparison with mixed forests – 86% to 77%(first planting pattern: Acacia sp. + noble hardwood species) and 54% (second planting pattern: Acacia + Dipterocarpus sp. + Sindora sp.). The average profit per hectare and year is almost five times higher in the case of mixed stands. The first planting pattern reaches 2,650 $, the second planting pattern 2,280 $ and the pure acacia plantation only 460 $. From an economic point of view, the cultivation of mixed forests that corresponds to the principles of sustainable forestry generates a good economical profit while maintaining habitat complexity and biodiversity.

Numerical Feasibility Study for Treated Wastewater Recharge as a Tool to Impede Saltwater Intrusion in the Coastal Aquifer of Gaza – Palestine

The ongoing depletion of the coastal aquifer in the Gaza strip due to groundwater overexploitation has led to the process of seawater intrusion, which is continually becoming a serious problem in Gaza, as the seawater has further invaded into many sections along the coastal shoreline. As a first step to get a hold on the problem, the artificial neural network (ANN)-model has been applied as a new approach and an attractive tool to study and predict groundwater levels without applying physically based hydrologic parameters, and also for the purpose to improve the understanding of complex groundwater systems and which is able to show the effects of hydrologic, meteorological and anthropogenic impacts on the groundwater conditions. Prediction of the future behaviour of the seawater intrusion process in the Gaza aquifer is thus of crucial importance to safeguard the already scarce groundwater resources in the region. In this study the coupled three-dimensional groundwater flow and density-dependent solute transport model SEAWAT, as implemented in Visual MODFLOW, is applied to the Gaza coastal aquifer system to simulate the location and the dynamics of the saltwater–freshwater interface in the aquifer in the time period 2000-2010. A very good agreement between simulated and observed TDS salinities with a correlation coefficient of 0.902 and 0.883 for both steady-state and transient calibration is obtained. After successful calibration of the solute transport model, simulation of future management scenarios for the Gaza aquifer have been carried out, in order to get a more comprehensive view of the effects of the artificial recharge planned in the Gaza strip for some time on forestall, or even to remedy, the presently existing adverse aquifer conditions, namely, low groundwater heads and high salinity by the end of the target simulation period, year 2040. To that avail, numerous management scenarios schemes are examined to maintain the ground water system and to control the salinity distributions within the target period 2011-2040. In the first, pessimistic scenario, it is assumed that pumping from the aquifer continues to increase in the near future to meet the rising water demand, and that there is not further recharge to the aquifer than what is provided by natural precipitation. The second, optimistic scenario assumes that treated surficial wastewater can be used as a source of additional artificial recharge to the aquifer which, in principle, should not only lead to an increased sustainable yield of the latter, but could, in the best of all cases, revert even some of the adverse present-day conditions in the aquifer, i.e., seawater intrusion. This scenario has been done with three different cases which differ by the locations and the extensions of the injection-fields for the treated wastewater. The results obtained with the first (do-nothing) scenario indicate that there will be ongoing negative impacts on the aquifer, such as a higher propensity for strong seawater intrusion into the Gaza aquifer. This scenario illustrates that, compared with 2010 situation of the baseline model, at the end of simulation period, year 2040, the amount of saltwater intrusion into the coastal aquifer will be increased by about 35 %, whereas the salinity will be increased by 34 %. In contrast, all three cases of the second (artificial recharge) scenario group can partly revert the present seawater intrusion. From the water budget point of view, compared with the first (do nothing) scenario, for year 2040, the water added to the aquifer by artificial recharge will reduces the amount of water entering the aquifer by seawater intrusion by 81, 77and 72 %, for the three recharge cases, respectively. Meanwhile, the salinity in the Gaza aquifer will be decreased by 15, 32 and 26% for the three cases, respectively.

Optimization of Processing Technology for Commercial Drying of Bananas (Matooke)

Summary - Cooking banana is one of the most important crops in Uganda; it is a staple food and source of household income in rural areas. The most common cooking banana is locally called matooke, a Musa sp triploid acuminate genome group (AAA-EAHB). It is perishable and traded in fresh form leading to very high postharvest losses (22-45%). This is attributed to: non-uniform level of harvest maturity, poor handling, bulk transportation and lack of value addition/processing technologies, which are currently the main challenges for trade and export, and diversified utilization of matooke. Drying is one of the oldest technologies employed in processing of agricultural produce. A lot of research has been carried out on drying of fruits and vegetables, but little information is available on matooke. Drying of matooke and milling it to flour extends its shelf-life is an important means to overcome the above challenges. Raw matooke flour is a generic flour developed to improve shelf stability of the fruit and to find alternative uses. It is rich in starch (80 - 85%db) and subsequently has a high potential as a calorie resource base. It possesses good properties for both food and non-food industrial use. Some effort has been done to commercialize the processing of matooke but there is still limited information on its processing into flour. It was imperative to carry out an in-depth study to bridge the following gaps: lack of accurate information on the maturity window within which matooke for processing into flour can be harvested leading to non-uniform quality of matooke flour; there is no information on moisture sorption isotherm for matooke from which the minimum equilibrium moisture content in relation to temperature and relative humidity is obtainable, below which the dry matooke would be microbiologically shelf-stable; and lack of information on drying behavior of matooke and standardized processing parameters for matooke in relation to physicochemical properties of the flour. The main objective of the study was to establish the optimum harvest maturity window and optimize the processing parameters for obtaining standardized microbiologically shelf-stable matooke flour with good starch quality attributes. This research was designed to: i) establish the optimum maturity harvest window within which matooke can be harvested to produce a consistent quality of matooke flour, ii) establish the sorption isotherms for matooke, iii) establish the effect of process parameters on drying characteristics of matooke, iv) optimize the drying process parameters for matooke, v) validate the models of maturity and optimum process parameters and vi) standardize process parameters for commercial processing of matooke. Samples were obtained from a banana plantation at Presidential Initiative on Banana Industrial Development (PIBID), Technology Business Incubation Center (TBI) at Nyaruzunga – Bushenyi in Western Uganda. A completely randomized design (CRD) was employed in selecting the banana stools from which samples for the experiments were picked. The cultivar Mbwazirume which is soft cooking and commonly grown in Bushenyi was selected for the study. The static gravitation method recommended by COST 90 Project (Wolf et al., 1985), was used for determination of moisture sorption isotherms. A research dryer developed for this research. All experiments were carried out in laboratories at TBI. The physiological maturity of matooke cv. mbwazirume at Bushenyi is 21 weeks. The optimum harvest maturity window for commercial processing of matooke flour (Raw Tooke Flour - RTF) at Bushenyi is between 15-21 weeks. The finger weight model is recommended for farmers to estimate harvest maturity for matooke and the combined model of finger weight and pulp peel ratio is recommended for commercial processors. Matooke isotherms exhibited type II curve behavior which is characteristic of foodstuffs. The GAB model best described all the adsorption and desorption moisture isotherms. For commercial processing of matooke, in order to obtain a microbiologically shelf-stable dry product. It is recommended to dry it to moisture content below or equal to 10% (wb). The hysteresis phenomenon was exhibited by the moisture sorption isotherms for matooke. The isoteric heat of sorption for both adsorptions and desorption isotherms increased with decreased moisture content. The total isosteric heat of sorption for matooke: adsorption isotherm ranged from 4,586 – 2,386 kJ/kg and desorption isotherm from 18,194– 2,391 kJ/kg for equilibrium moisture content from 0.3 – 0.01 (db) respectively. The minimum energy required for drying matooke from 80 – 10% (wb) is 8,124 kJ/kg of water removed. Implying that the minimum energy required for drying of 1 kg of fresh matooke from 80 - 10% (wb) is 5,793 kJ. The drying of matooke takes place in three steps: the warm-up and the two falling rate periods. The drying rate constant for all processing parameters ranged from 5,793 kJ and effective diffusivity ranged from 1.5E-10 - 8.27E-10 m2/s. The activation energy (Ea) for matooke was 16.3kJ/mol (1,605 kJ/kg). Comparing the activation energy (Ea) with the net isosteric heat of sorption for desorption isotherm (qst) (1,297.62) at 0.1 (kg water/kg dry matter), indicated that Ea was higher than qst suggesting that moisture molecules travel in liquid form in matooke slices. The total color difference (ΔE*) between the fresh and dry samples, was lowest for effect of thickness of 7 mm, followed by air velocity of 6 m/s, and then drying air temperature at 70˚C. The drying system controlled by set surface product temperature, reduced the drying time by 50% compared to that of a drying system controlled by set air drying temperature. The processing parameters did not have a significant effect on physicochemical and quality attributes, suggesting that any drying air temperature can be used in the initial stages of drying as long as the product temperature does not exceed gelatinization temperature of matooke (72˚C). The optimum processing parameters for single-layer drying of matooke are: thickness = 3 mm, air temperatures 70˚C, dew point temperature 18˚C and air velocity 6 m/s overflow mode. From practical point of view it is recommended that for commercial processing of matooke, to employ multi-layer drying of loading capacity equal or less than 7 kg/m², thickness 3 mm, air temperatures 70˚C, dew point temperature 18˚C and air velocity 6 m/s overflow mode.

Lebensmittelqualität zwischen Geschmack und Zeichen

Ziel der vorliegenden Arbeit war es, Lebensmittelqualität am Beispiel von Speisequark aus hofeigener und industrieller Verarbeitung mit natur- und kulturwissenschaftlichen Methoden zu erfassen bzw. zu betrachten. Das Neue dieser interdisziplinären Arbeit lag in der Entwicklung von Verbindungen zwischen hedonischen/sensorischen, ökologischen und kulturellen Qualitäten von Speisequark. Im zweiten Teil der Arbeit wurde eine sensorische Schulung für die hofeigene Milchverarbeitung entwickelt und erprobt, um die Ergebnisse dieser Arbeit in die Praxis umzusetzen. Zuerst musste ein theoretischer Ansatz entwickelt werden, der die Esshandlungen der Verbraucher als Integrationsmoment von objektiven, subjektiven und sozial-kulturellen Qualitäten betrachtet. Bei diesem handlungstheoretischen Ansatz galt es, die Trennung zwischen objektiven und subjektiven Qualitäten zu überwinden, indem über Esshandlungen der Verbraucher integrierte Verbindungen zwischen hedonischen/sensorischen, ökologischen und kulturellen Qualitäten am Beispiel von Speisequark entwickelt wurden. Als empirische Grundlage wurde erstens die sensorische Qualität mit Profilprüfungen erfasst. Zweitens wurde die ökologische Qualität mit einer Verbraucherumfrage und Conjoint-Analyse und drittens die kulturelle Qualität mit einer semiotischen Analyse betrachtet. Die diskursiven Begründungen des Esshandelns, die in ermittelnden Gruppendiskussionen qualitativ erhoben wurden, zeigten deutlich, dass diese drei Qualitäten des Hofquarks untrennbar miteinander verbunden sind. Der komplexe Begriff authentisch, mit dem die Verbraucher Hofquark charakterisierten, beinhaltete vor allem den Geschmack, aber auch die damit verbundene handwerkliche Herstellungsweise, die Verpackung, die regionale Herkunft und die ökologische Anbauweise. Hofquark ist aus Verbrauchersicht ein gutes Lebensmittel, das seine besondere Bedeutung (kulturellen Wert) auch dadurch erhält, was es nicht ist, nämlich ein industrielles Molkereiprodukt. Der neue natur- und kulturwissenschaftliche Ansatz dieser Arbeit stellt gleichzeitig ein Plädoyer für eine mehrdimensionale Qualitätsbetrachtung von Lebensmitteln dar. Aus interdisziplinärer Sicht besteht hierzu noch ein großer Forschungsbedarf.

Diazafluoren-9-yliden als Bindungsmotiv für Metallfragmente in kreuzkonjugierten π-Systemen

In der vorliegenden Dissertation wurden kreuzkonjugierte organische Verbindungen basierend auf Diazafluorenmethyliden- sowie Dipyridylmethyliden-Bausteinen synthetisiert, die zum einen photoredoxaktive Metallfragmente komplexieren können und zum anderen erweiterte π-konjugierte Pfade auf der Grundlage von Alkineinheiten ermöglichen. Das kreuzkonjugierte Motiv wurde über die Kupplung von Alkineinheiten an halogenierte Methyliden-Einheiten, den so genannten Dibromolefinen, zugänglich gemacht. Zur Synthese von Dibromolefinen wurden verschiedene Methoden untersucht. Literaturbekannte Methoden wie die Wittig-Reaktion und ihre Modifikationen sowie die Corey-Fuchs-Reaktion konnten für die Diazafluoreneinheit nicht erfolgreich angewendet werden. Bei einer mikrowellenunterstützten Reaktion konnte sowohl ausgehend von Diazafluoren-9-on als auch von Di-2-pyridylketon eine Dibromolefinierung (55 % und 65 %) erreicht werden. Die Eignung der Mikrowellenstrahlung für Dibromolefinierungsreaktionen nach Corey und Fuchs wurde weiterhin an verschiedenen Aldehyden und Ketonen untersucht. In den meisten Fällen konnten gute bis sehr gute Ergebnisse erzielt werden. Durch die erfolgreiche Synthese von Dibromolefinen über Mikrowellensynthese wurde die Realisierung von diversen π-konjugierten Systemen möglich. Dies erfolgte exemplarisch durch die Kupplung der Alkine 5-Ethinyl-2,2’-bipyridin, 1-(Ferrocenylethinyl)-4-(ethinyl)benzol, Tri(tolyl)propin sowie der TIPS- und TMS-Acetylene. Neben der Vielfalt an Möglichkeiten zur Funktionalisierung von Dipyridyl- und Diazafluorenbausteinen zeigte sich zudem, dass sogar räumlich anspruchsvolle Verbindungen wie die geminale angeordneten voluminösen Tri(tolyl)propinyl-Substituenten an der Doppelbindung erfolgreich synthetisiert werden können. Die Koordinationseigenschaften der neu synthetisierten Verbindungen konnten durch Umsetzungen der Diazafluoren- und Dipyridylverbindungen mit PdCl2 und [RuCl2(bpy)2] erfolgreich gezeigt werden. Im Hinblick auf die Herstellung von Funktionsmaterialien eignen sich die Endiin-Strukturmotive aufgrund von diversen Variationsmöglichkeiten wie Koordination von Übergangsmetallen sowie Funktionalisierung der Peripherie gut. Dadurch können die elektronischen Eigenschaften wie die Absorption oder elektrochemische Potentiale der Verbindungen modifiziert werden. Die UV/Vis-Spektren der neu synthetisierten Verbindungen zeigen, dass Absorptionen in längerwelligen Bereichen durch Verlängerung des Konjugationspfades gesteuert werden können. Zudem lassen sich weitere photophysikalische Eigenschaften wie MC-, LC-, LMCT- oder MLCT-Übergänge durch Koordination von Metallen generieren. Die elektrochemischen Potentiale der Dipyridyl- und Diazafluorenbausteine konnten durch Anbindung von verschiedenen Substituenten beeinflusst werden. Es zeigte sich, dass sich die Reduktionswellen im Vergleich zu denen der Ketone zu niedrigeren Potentialen verschieben, wenn Alkine an die Dipyridylmethyliden- und Diazafluorenmethyliden-Bausteine geknüpft wurden. Zudem konnte beobachtet werden, dass die Signale nicht immer reversibel sind. Insbesondere die Dipyridylverbindungen zeichneten sich durch irreversible Reduktionswellen aus. Die Realisierung von π-konjugierten Systemen gelang auch mit cyclischen kohlenstoffbasierten Verbindungen. Über das separat synthetisierte 2,2’-Diethinyltolan konnte eine cyclische Verbindung, ein dehydroannulen-radialenisches System, erfolgreich hergestellt werden. Die Koordination von redoxaktiven Metallzentren wie [Ru(bpy)2] konnte für diese Verbindung ebenfalls erfolgreich gezeigt werden. Die elektronische Wechselwirkung zwischen dem Metallzentrum und dem dehydroannulenischen System könnte sowohl über theoretische Methoden (zeitabhängige Dichtefunktionaltheorie) als auch experimentell wie z. B. über transiente Absorptionsspektroskopie untersucht werden. Diese zukünftig durchzuführenden Untersuchungen können Aufschluss über die Ladungstransferraten und -dauer geben. Im Hinblick auf die Realisierung von Modellverbindungen für molekulare Drähte wurden lineare Systeme basierend auf der Diazafluoreneinheit synthetisiert. Zur Synthese von derartigen Systemen war es zunächst notwendig, die Dibromolefine unsymmetrisch zu alkinylieren. Die unsymmetrische Substitution gestaltete sich als Herausforderung, da eine Einfachkupplung mit einem Acetylen nicht möglich war. In den meisten Fällen wurden zweifach substituierte Spezies mit den identischen Alkinen erhalten. Die besten Ausbeuten konnten durch die konsekutive Zugabe von TIPS-Acetylen und darauffolgend TMS-Acetylen in die Reaktionsmischung erhalten werden. Offenbar spielt der räumliche Anspruch des Erstsubstituenten in diesem Zusammenhang eine Rolle. Die selektive Entschützung der unterschiedlich silylierten Verbindungen erfolgte mit K2CO3 in MeOH/THF (1:1). Die oxidative Homokupplungsreaktion erfolgte ohne Isolierung der entschützten Spezies, da diese instabil ist und zur Polymerisation neigt. Aufgrund der Instabilität der entschützten Spezies sowie möglichen Nebenreaktionen waren die Ausbeuten sowohl bei der TIPS-geschützten Verbindung als auch bei der TTP-geschützten Verbindung gering. Versuche, lineare Systeme von dipyridylbasierten Verbindungen zu erhalten, schlugen fehl. Die π-konjugierten Systeme lassen aufgrund der effektiven Überlappung der beteiligten π-Orbitale hohe Ladungsträgermobilitäten vermuten. Die im Rahmen dieser Arbeit synthetisierten Verbindungen könnten mit Schwefelverbindungen die Anbindung an Elektroden zulassen, worüber die Leitfähigkeiten der Verbindungen gemessen werden könnten.

Efficient Characterisation and Optimal Control of Open Quantum Systems - Mathematical Foundations and Physical Applications

Since no physical system can ever be completely isolated from its environment, the study of open quantum systems is pivotal to reliably and accurately control complex quantum systems. In practice, reliability of the control field needs to be confirmed via certification of the target evolution while accuracy requires the derivation of high-fidelity control schemes in the presence of decoherence. In the first part of this thesis an algebraic framework is presented that allows to determine the minimal requirements on the unique characterisation of arbitrary unitary gates in open quantum systems, independent on the particular physical implementation of the employed quantum device. To this end, a set of theorems is devised that can be used to assess whether a given set of input states on a quantum channel is sufficient to judge whether a desired unitary gate is realised. This allows to determine the minimal input for such a task, which proves to be, quite remarkably, independent of system size. These results allow to elucidate the fundamental limits regarding certification and tomography of open quantum systems. The combination of these insights with state-of-the-art Monte Carlo process certification techniques permits a significant improvement of the scaling when certifying arbitrary unitary gates. This improvement is not only restricted to quantum information devices where the basic information carrier is the qubit but it also extends to systems where the fundamental informational entities can be of arbitary dimensionality, the so-called qudits. The second part of this thesis concerns the impact of these findings from the point of view of Optimal Control Theory (OCT). OCT for quantum systems utilises concepts from engineering such as feedback and optimisation to engineer constructive and destructive interferences in order to steer a physical process in a desired direction. It turns out that the aforementioned mathematical findings allow to deduce novel optimisation functionals that significantly reduce not only the required memory for numerical control algorithms but also the total CPU time required to obtain a certain fidelity for the optimised process. The thesis concludes by discussing two problems of fundamental interest in quantum information processing from the point of view of optimal control - the preparation of pure states and the implementation of unitary gates in open quantum systems. For both cases specific physical examples are considered: for the former the vibrational cooling of molecules via optical pumping and for the latter a superconducting phase qudit implementation. In particular, it is illustrated how features of the environment can be exploited to reach the desired targets.