Classification of recycled sands and their applications as fine aggregates for concrete and bituminous mixtures

As a result of the drive towards waste-poor world and reserving the non-renewable materials, recycling the construction and demolition materials become very essential. Now reuse of the recycled concrete aggregate more than 4 mm in producing new concrete is allowed but with natural sand a fine aggregate while. While the sand portion that represent about 30\% to 60\% of the crushed demolition materials is disposed off. To perform this research, recycled concrete sand was produced in the laboratory while nine recycled sands produced from construction and demolitions materials and two sands from natural crushed limestone were delivered from three plants. Ten concrete mix designs representing the concrete exposition classes XC1, XC2, XF3 and XF4 according to European standard EN 206 were produced with partial and full replacement of natural sand by the different recycled sands. Bituminous mixtures achieving the requirements of base courses according to Germany standards and both base and binder courses according to Egyptian standards were produced with the recycled sands as a substitution to the natural sands. The mechanical properties and durability of concrete produced with the different recycled sands were investigated and analyzed. Also the volumetric analysis and Marshall test were performed hot bituminous mixtures produced with the recycled sands. According to the effect of replacement the natural sand by the different recycled sands on the concrete compressive strength and durability, the recycled sands were classified into three groups. The maximum allowable recycled sand that can be used in the different concrete exposition class was determined for each group. For the asphalt concrete mixes all the investigated recycled sands can be used in mixes for base and binder courses up to 21\% of the total aggregate mass.

Thermoaktive Bauteilsysteme - Ein neuer simulationstechnischer Berechnungsansatz

Thermoaktive Bauteilsysteme sind Bauteile, die als Teil der Raumumschließungsflächen über ein integriertes Rohrsystem mit einem Heiz- oder Kühlmedium beaufschlagt werden können und so die Beheizung oder Kühlung des Raumes ermöglichen. Die Konstruktionenvielfalt reicht nach diesem Verständnis von Heiz, bzw. Kühldecken über Geschoßtrenndecken mit kern-integrierten Rohren bis hin zu den Fußbodenheizungen. Die darin enthaltenen extrem trägen Systeme werden bewußt eingesetzt, um Energieangebot und Raumenergiebedarf unter dem Aspekt der rationellen Energieanwendung zeitlich zu entkoppeln, z. B. aktive Bauteilkühlung in der Nacht, passive Raumkühlung über das kühle Bauteil am Tage. Gebäude- und Anlagenkonzepte, die träge reagierende thermoaktive Bauteilsysteme vorsehen, setzen im kompetenten und verantwortungsvollen Planungsprozeß den Einsatz moderner Gebäudesimulationswerkzeuge voraus, um fundierte Aussagen über Behaglichkeit und Energiebedarf treffen zu können. Die thermoaktiven Bauteilsysteme werden innerhalb dieser Werkzeuge durch Berechnungskomponenten repräsentiert, die auf mathematisch-physikalischen Modellen basieren und zur Lösung des bauteilimmanenten mehrdimensionalen instationären Wärmeleitungsproblems dienen. Bisher standen hierfür zwei unterschiedliche prinzipielle Vorgehensweisen zur Lösung zur Verfügung, die der physikalischen Modellbildung entstammen und Grenzen bzgl. abbildbarer Geometrie oder Rechengeschwindigkeit setzen. Die vorliegende Arbeit dokumentiert eine neue Herangehensweise, die als experimentelle Modellbildung bezeichnet wird. Über den Weg der Systemidentifikation können aus experimentell ermittelten Datenreihen die Parameter für ein kompaktes Black-Box-Modell bestimmt werden, das das Eingangs-Ausgangsverhalten des zugehörigen beliebig aufgebauten thermoaktiven Bauteils mit hinreichender Genauigkeit widergibt. Die Meßdatenreihen lassen sich über hochgenaue Berechnungen generieren, die auf Grund ihrer Detailtreue für den unmittelbaren Einsatz in der Gebäudesimulation ungeeignet wären. Die Anwendung der Systemidentifikation auf das zweidimensionale Wärmeleitungsproblem und der Nachweis ihrer Eignung wird an Hand von sechs sehr unterschiedlichen Aufbauten thermoaktiver Bauteilsysteme durchgeführt und bestätigt sehr geringe Temperatur- und Energiebilanzfehler. Vergleiche zwischen via Systemidentifikation ermittelten Black-Box-Modellen und physikalischen Modellen für zwei Fußbodenkonstruktionen zeigen, daß erstgenannte auch als Referenz für Genauigkeitsabschätzungen herangezogen werden können. Die Praktikabilität des neuen Modellierungsansatzes wird an Fallstudien demonstriert, die Ganzjahressimulationen unter Bauteil- und Betriebsvariationen an einem exemplarischen Büroraum betreffen. Dazu erfolgt die Integration des Black-Box-Modells in das kommerzielle Gebäude- und Anlagensimulationsprogramm CARNOT. Die akzeptablen Rechenzeiten für ein Einzonen-Gebäudemodell in Verbindung mit den hohen Genauigkeiten bescheinigen die Eignung der neuen Modellierungsweise.

Role of Rab5 in synaptic vesicle recycling

During synaptic transmission, NT-filled synaptic vesicles are released by Ca2+-triggered exocytosis at the active zone. Following exocytosis, SV membrane is immediately re-internalized and synaptic vesicles (SVs) are regenerated by a local recycling mechanism within the presynaptic terminal. It is debated whether an endosomal compartment is involved in this recycling process. In contrast, it is well known from cultured mammalian cells, that endocytic vesicles fuse to the early sorting endosome. The early endosome is a major sorting station of the cell where cargo is send into the degradative pathway to late endosome and lysosome or towards recycling. Each trafficking step is mediated by a certain protein of the Rab family. Rab proteins are small GTPases belonging to the Ras superfamily. They accumulate at their target compartments and have thereby been used as markers for the different endocytic organelles in cultured mammalian cells. Rab5 controls trafficking from the PM to the early endosome and has thereby been used as marker for this compartment. A second marker is based on the specific binding of the FYVE zinc finger protein domain to the lipid PI(3)P that is specifically generated at the early endosomal membrane. This study used the Drosophila NMJ as a model system to investigate the SV recycling process. In particular, three questions were addressed: First, is an endosomal compartment present at the synapse? Second, do SVs recycle through an endosome? Third, is Rab5 involved in SV recycling? We used GFP fusions of Rab5 and 2xFYVE to visualize endosomal compartments at the presynaptic terminal of Drosophila third instar larval NMJs. Furthermore, the endosomes are located within the pool of recycling SVs, labeled with the styryl-dye FM5-95. Using the temperature-sensitive mutation in Dynamin, shibirets, we showed that SV recycling involves trafficking through an intermediate endosomal compartment. In cultured mammalian cells, interfering with Rab5 function by expressing the dominant negative version, Rab5SN causes the fragmentation of the endosome and the accumulation of endocytic vesicles. In contrast, when Rab5 is overexpressed enlarged endosomal compartments were observed. In Drosophila, the endosomal compartment was disrupted when loss of function and dominant negative mutants of Rab5 were expressed. In addition, at the ultrastructural we observed an accumulation of endocytic vesicles in Rab5S43N expressing terminals and enlarged endosomes when Rab5 was overexpressed. Furthermore, interfering with Rab5 function using the dominant negative Rab5S43N caused a decrease in the SV recycling kinetics as shown by FM1-43 experiments. In contrast, overexpression of Rab5 or GFP-Rab5 caused an increase in the FM1-43 internalization rate. Finally, standard electrophysiological techniques were used to measure synaptic function. We found that the Rab5-mediated endosomal SV recycling pathway generates vesicles with a higher fusion efficacy during Ca2+-triggered release, compared to SVs recycled when Rab5 function was impaired. We therefore suggest a model in which the endosome serves as organelle to control the SV fusion efficacy and thereby the synaptic strength. Since changes in the synaptic strength are occuring during learning and memory processes, controlling endosomal SV recycling might be a new molecular mechanism involved in learning and memory.

Farmers’ desired traits and selection criteria for maize varieties and their implications for maize breeding: A case study from KwaZulu-Natal Province, South Africa

Adoption of hybrids and improved varieties has remained low in the smallholder farming sector of South Africa, despite maize being the staple food crop for the majority of households. The objective of this study was to establish preferred maize characteristics by farmers which can be used as selection criteria by maize breeders in crop improvement. Data were collected from three villages of a selected smallholder farming area in South Africa using a survey covering 300 households and participatory rural appraisal methodology. Results indicated a limited selection of maize varieties grown by farmers in the area compared to other communities in Africa. More than 97% of the farmers grew a local landrace called Natal-8-row or IsiZulu. Hybrids and improved open pollinated varieties were planted by less than 40% of the farmers. The Natal-8-row landrace had characteristics similar to landraces from eastern and southern Africa and closely resembled Hickory King, a landrace still popular in Southern Africa. The local landrace was preferred for its taste, recycled seed, tolerance to abiotic stresses and yield stability. Preferred characteristics of maize varieties were high yield and prolificacy, disease resistance, early maturity, white grain colour, and drying and shelling qualities. Farmers were willing to grow hybrids if the cost of seed and other inputs were affordable and their preferences were considered. Our results show that breeding opportunities exist for improving the farmers’ local varieties and maize breeders can take advantage of these preferred traits and incorporate them into existing high yielding varieties.