Development of directly modulated high speed telecommunication lasers based on surface defined feedback gratings

High-speed semiconductor lasers are an integral part in the implemen- tation of high-bit-rate optical communications systems. They are com- pact, rugged, reliable, long-lived, and relatively inexpensive sources of coherent light. Due to the very low attenuation window that exists in the silica based optical fiber at 1.55 μm and the zero dispersion point at 1.3 μm, they have become the mainstay of optical fiber com- munication systems. For the fabrication of lasers with gratings such as, distributed bragg reflector or distributed feedback lasers, etching is the most critical step. Etching defines the lateral dimmensions of the structure which determines the performance of optoelectronic devices. In this thesis studies and experiments were carried out about the exist- ing etching processes for InP and a novel dry etching process was de- veloped. The newly developed process was based on Cl2/CH4/H2/Ar chemistry and resulted in very smooth surfaces and vertical side walls. With this process the grating definition was significantly improved as compared to other technological developments in the respective field. A surface defined grating definition approach is used in this thesis work which does not require any re-growth steps and makes the whole fabrication process simpler and cost effective. Moreover, this grating fabrication process is fully compatible with nano-imprint lithography and can be used for high throughput low-cost manufacturing. With usual etching techniques reported before it is not possible to etch very deep because of aspect ratio dependent etching phenomenon where with increasing etch depth the etch rate slows down resulting in non-vertical side walls and footing effects. Although with our de- veloped process quite vertical side walls were achieved but footing was still a problem. To overcome the challenges related to grating defini- tion and deep etching, a completely new three step gas chopping dry etching process was developed. This was the very first time that a time multiplexed etching process for an InP based material system was demonstrated. The developed gas chopping process showed extra ordinary results including high mask selectivity of 15, moderate etch- ing rate, very vertical side walls and a record high aspect ratio of 41. Both the developed etching processes are completely compatible with nano imprint lithography and can be used for low-cost high-throughput fabrication. A large number of broad area laser, ridge waveguide laser, distributed feedback laser, distributed bragg reflector laser and coupled cavity in- jection grating lasers were fabricated using the developed one step etch- ing process. Very extensive characterization was done to optimize all the important design and fabrication parameters. The devices devel- oped have shown excellent performance with a very high side mode suppression ratio of more than 52 dB, an output power of 17 mW per facet, high efficiency of 0.15 W/A, stable operation over temperature and injected currents and a threshold current as low as 30 mA for almost 1 mm long device. A record high modulation bandwidth of 15 GHz with electron-photon resonance and open eye diagrams for 10 Gbps data transmission were also shown.

1.55 µm High-Speed QDs Lasers for Optical Telecommunication Applications

In this work investigation of the QDs formation and the fabrication of QD based semiconductor lasers for telecom applications are presented. InAs QDs grown on AlGaInAs lattice matched to InP substrates are used to fabricate lasers operating at 1.55 µm, which is the central wavelength for far distance data transmission. This wavelength is used due to its minimum attenuation in standard glass fibers. The incorporation of QDs in this material system is more complicated in comparison to InAs QDs in the GaAs system. Due to smaller lattice mismatch the formation of circular QDs, elongated QDs and quantum wires is possible. The influence of the different growth conditions, such as the growth temperature, beam equivalent pressure, amount of deposited material on the formation of the QDs is investigated. It was already demonstrated that the formation process of QDs can be changed by the arsenic species. The formation of more round shaped QDs was observed during the growth of QDs with As2, while for As4 dash-like QDs. In this work only As2 was used for the QD growth. Different growth parameters were investigated to optimize the optical properties, like photoluminescence linewidth, and to implement those QD ensembles into laser structures as active medium. By the implementation of those QDs into laser structures a full width at half maximum (FWHM) of 30 meV was achieved. Another part of the research includes the investigation of the influence of the layer design of lasers on its lasing properties. QD lasers were demonstrated with a modal gain of more than 10 cm-1 per QD layer. Another achievement is the large signal modulation with a maximum data rate of 15 Gbit/s. The implementation of optimized QDs in the laser structure allows to increase the modal gain up to 12 cm-1 per QD layer. A reduction of the waveguide layer thickness leads to a shorter transport time of the carriers into the active region and as a result a data rate up to 22 Gbit/s was achieved, which is so far the highest digital modulation rate obtained with any 1.55 µm QD laser. The implementation of etch stop layers into the laser structure provide the possibility to fabricate feedback gratings with well defined geometries for the realization of DFB lasers. These DFB lasers were fabricated by using a combination of dry and wet etching. Single mode operation at 1.55 µm with a high side mode suppression ratio of 50 dB was achieved.

Fluoreszenz und Lasertätigkeit in dünnen amorphen Schichten von Spirobifluorenderivaten

Es wurden die optischen Eigenschaften einiger Spirooligophenylverbindungen untersucht. Bei den Verbindungen handelte es sich um lineare und verzweigte Derivate des Spirobifluorens. Es wurden dünne amorphe Schichten der Verbindungen mittels spincoating und Vakuumverdampfen (OMBD) auf unterschiedlichen Substraten hergestellt. Mit spektroskopischer Ellipsometrie konnten die Schichtdicken und optische Konstanten der dünnen Schichten bestimmt werden. Dafür sind die Extinktionsspektren mit Tauc-Lorentz-Oszillatoren modelliert worden. Auf diese Weise ließen sich die optischen Konstanten der amorphen Filme besser beschreiben als mit den üblicherweise verwendeten Gauß-Oszillatoren. In dünnen Filmen von Spirosexiphenyl konnte uniaxiale Anisotropie nachgewiesen werden. Im Bereich der pie,pie*-Bande beträgt das Verhältnis des ordentlichen zum außerordentlichen Extinktionskoeffizienten 2.09. Mit einer Integrationskugel wurden die absoluten Quantenausbeuten der Fluoreszenz in festen Filmen bestimmt. Dafür ist ein vereinfachtes Verfahren der Auswertung entwickelt worden. Im Vergleich der untersuchten Substanzen zeigt sich, dass die Verbindungen mit dem Sexiphenyl-Chromophor höhere Quantenausbeuten im Festkörper haben (31 % - 48 %) als die Verbindungen mit Quaterphenyl als Chromophor (15 % - 30 %). In den beiden Klassen haben jeweils die sterisch anspruchsvollen Octopusvarianten die höchsten Festkörperquantenausbeuten. Durch verdünnen mit m,m-Spirosexiphenyl konnte die Quantenausbeute von p,p-Spirosexiphenyl in dünnen festen Filmen bis auf 65 % (95 % m,m- und 5 % p,p-Spirosexiphenyl) gesteigert werden. Eine Korrelation der Quantenausbeuten in Lösung und im festen, unverdünnten Film wurde nicht festgestellt. Als dünne Filme in Wellenleitergeometrie zeigen Spirooligophenyle bei optischer Anregung verstärkte spontane Emission (ASE). Dies manifestiert sich in einer Einengung des Emissionsspektrums mit zunehmender Pumpleistungsdichte. Auch für stimulierte Emission sind die Verbindungen mit Sexiphenylchromophor besser geeignet. Die niedrigste Schwelle in einer unverdünnten Reinsubstanz wurde mit 0.23 µJ/cm² in einer aufgeschleuderten Schicht Spirosexiphenyl gemessen. Auch 4-Spiro³, Spiro-SPO und Octo-2 zeigten niedrige ASE-Schwellen von 0.45 µJ/cm², 0.45 µJ/cm² und 0.5 µJ/cm². Die ASE-Schwellwerte von Spiroquaterphenyl und seinen beiden Derivaten Methoxyspiroquaterphenyl und Octo-1 sind mit 1.8 µJ/cm², 1.4 µJ/cm² und 1.2 µJ/cm² höher als die der Sexiphenylderivate. Im gemischten System aus m,m- und p,p-Spirosexiphenyl konnte die ASE-Schwelle noch weiter gesenkt werden. Bei einer Konzentration von 5 % p,p-Spirosexiphenyl wurde ein Schwellwert von nur 100 nJ/cm² bestimmt. Durch Dotierung mit unterschiedlichen Farbstoffen in Spirosexiphenyl als Matrix konnte ASE fast über den gesamten sichtbaren Spektralbereich gezeigt werden. Mit der „variable Streifenlänge“ (VSL-) -Methode wurden die pumpleistungsabhängigen Gainspektren dünner aufgedampfter Proben gemessen. Hieraus konnten die Wechselwirkungsquerschnitte der stimulierten Emission der Substanzen ermittelt werden. In Übereinstimmung mit den Verhältnissen bei den Festkörperfluoreszenzquantenausbeuten und den Schwellwerten der ASE sind auch bei den Gainkoeffizienten reiner Spirooligophenyle die besten Werte bei den Sexiphenylderivaten gefunden worden. Der Wirkungsquerschnitt der stimulierten Emission beträgt für Methylspiroquaterphenyl und Octo-1 ca. 1.8*10^-17 cm². Für Spiro-SPO und Spirosexiphenyl wurden Wirkungsquerschnitte von 7.5*10^-17 cm² bzw. 9.2*10^-17 cm² bestimmt. Noch etwas größer waren die Werte im gemischten System aus m,m- und p,p-Spirosexiphenyl (1.1*10^-16 cm²) und für DPAVB dotiert in Spirosexiphenyl (1.4*10^-16 cm²). Der höchste Maximalwert des Gainkoeffizienten von 328 cm-1 bei einer absorbierten Pumpenergiedichte von 149 µJ/cm² wurde mit Spirosexiphenyl erreicht. Abschließend wurden DFB-Laser-Strukturen mit reinen und dotierten Spirooligophenylverbindungen als aktiven Materialien vorgestellt. Mit Spiroterphenyl konnte ein DFB-Laser mit der bisher kürzesten Emissionswellenlänge (361.9 nm) in einem organischen Festkörperlaser realisiert werden. Mit reinen Spirooligophenylverbindungen und Mischungen daraus habe ich DFB-Lasing bei Wellenlängen zwischen 361.9 nm und 479 nm aufgezeigt. Durch Dotierung mit DPAVB wurde der Bereich der erreichbaren Wellenlängen bis 536 nm erweitert, bei gleichzeitiger Erniedrigung der Schwellenergiedichten für Lasertätigkeit. Bei Emissionswellenlängen von 495 nm bis 536 nm blieb die Laserschwelle zwischen 0.8 µJ/cm² und 1.1 µJ/cm². Diese Werte sind für DFB-Laser zweiter Ordnung sehr niedrig und geben Anlass zu glauben, dass sich mit DFB-Strukturen erster Ordnung Schwellen im Nanojoule Bereich erzielen lassen. Damit würde man den Bedingungen für elektrisch gepumpten Betrieb nahe kommen.

Development of hybrid UV VCSEL with organic active material and dielectric DBR mirrors for medical, sensoric and data storage applications

Lasers play an important role for medical, sensoric and data storage devices. This thesis is focused on design, technology development, fabrication and characterization of hybrid ultraviolet Vertical-Cavity Surface-Emitting Lasers (UV VCSEL) with organic laser-active material and inorganic distributed Bragg reflectors (DBR). Multilayer structures with different layer thicknesses, refractive indices and absorption coefficients of the inorganic materials were studied using theoretical model calculations. During the simulations the structure parameters such as materials and thicknesses have been varied. This procedure was repeated several times during the design optimization process including also the feedback from technology and characterization. Two types of VCSEL devices were investigated. The first is an index coupled structure consisting of bottom and top DBR dielectric mirrors. In the space in between them is the cavity, which includes active region and defines the spectral gain profile. In this configuration the maximum electrical field is concentrated in the cavity and can destroy the chemical structure of the active material. The second type of laser is a so called complex coupled VCSEL. In this structure the active material is placed not only in the cavity but also in parts of the DBR structure. The simulations show that such a distribution of the active material reduces the required pumping power for reaching lasing threshold. High efficiency is achieved by substituting the dielectric material with high refractive index for the periods closer to the cavity. The inorganic materials for the DBR mirrors have been deposited by Plasma- Enhanced Chemical Vapor Deposition (PECVD) and Dual Ion Beam Sputtering (DIBS) machines. Extended optimizations of the technological processes have been performed. All the processes are carried out in a clean room Class 1 and Class 10000. The optical properties and the thicknesses of the layers are measured in-situ by spectroscopic ellipsometry and spectroscopic reflectometry. The surface roughness is analyzed by atomic force microscopy (AFM) and images of the devices are taken with scanning electron microscope (SEM). The silicon dioxide (SiO2) and silicon nitride (Si3N4) layers deposited by the PECVD machine show defects of the material structure and have higher absorption in the ultra violet range compared to ion beam deposition (IBD). This results in low reflectivity of the DBR mirrors and also reduces the optical properties of the VCSEL devices. However PECVD has the advantage that the stress in the layers can be tuned and compensated, in contrast to IBD at the moment. A sputtering machine Ionsys 1000 produced by Roth&Rau company, is used for the deposition of silicon dioxide (SiO2), silicon nitride (Si3N4), aluminum oxide (Al2O3) and zirconium dioxide (ZrO2). The chamber is equipped with main (sputter) and assisted ion sources. The dielectric materials were optimized by introducing additional oxygen and nitrogen into the chamber. DBR mirrors with different material combinations were deposited. The measured optical properties of the fabricated multilayer structures show an excellent agreement with the results of theoretical model calculations. The layers deposited by puttering show high compressive stress. As an active region a novel organic material with spiro-linked molecules is used. Two different materials have been evaporated by utilizing a dye evaporation machine in the clean room of the department Makromolekulare Chemie und Molekulare Materialien (mmCmm). The Spiro-Octopus-1 organic material has a maximum emission at the wavelength λemission = 395 nm and the Spiro-Pphenal has a maximum emission at the wavelength λemission = 418 nm. Both of them have high refractive index and can be combined with low refractive index materials like silicon dioxide (SiO2). The sputtering method shows excellent optical quality of the deposited materials and high reflection of the multilayer structures. The bottom DBR mirrors for all VCSEL devices were deposited by the DIBS machine, whereas the top DBR mirror deposited either by PECVD or by combination of PECVD and DIBS. The fabricated VCSEL structures were optically pumped by nitrogen laser at wavelength λpumping = 337 nm. The emission was measured by spectrometer. A radiation of the VCSEL structure at wavelength 392 nm and 420 nm is observed.