Relativistic LCAO with Minimax Principle and New Balanced Basis Sets

Relativistic density functional theory is widely applied in molecular calculations with heavy atoms, where relativistic and correlation effects are on the same footing. Variational stability of the Dirac Hamiltonian is a very important field of research from the beginning of relativistic molecular calculations on, among efforts for accuracy, efficiency, and density functional formulation, etc. Approximations of one- or two-component methods and searching for suitable basis sets are two major means for good projection power against the negative continuum. The minimax two-component spinor linear combination of atomic orbitals (LCAO) is applied in the present work for both light and super-heavy one-electron systems, providing good approximations in the whole energy spectrum, being close to the benchmark minimax finite element method (FEM) values and without spurious and contaminated states, in contrast to the presence of these artifacts in the traditional four-component spinor LCAO. The variational stability assures that minimax LCAO is bounded from below. New balanced basis sets, kinetic and potential defect balanced (TVDB), following the minimax idea, are applied with the Dirac Hamiltonian. Its performance in the same super-heavy one-electron quasi-molecules shows also very good projection capability against variational collapse, as the minimax LCAO is taken as the best projection to compare with. The TVDB method has twice as many basis coefficients as four-component spinor LCAO, which becomes now linear and overcomes the disadvantage of great time-consumption in the minimax method. The calculation with both the TVDB method and the traditional LCAO method for the dimers with elements in group 11 of the periodic table investigates their difference. New bigger basis sets are constructed than in previous research, achieving high accuracy within the functionals involved. Their difference in total energy is much smaller than the basis incompleteness error, showing that the traditional four-spinor LCAO keeps enough projection power from the numerical atomic orbitals and is suitable in research on relativistic quantum chemistry. In scattering investigations for the same comparison purpose, the failure of the traditional LCAO method of providing a stable spectrum with increasing size of basis sets is contrasted to the TVDB method, which contains no spurious states already without pre-orthogonalization of basis sets. Keeping the same conditions including the accuracy of matrix elements shows that the variational instability prevails over the linear dependence of the basis sets. The success of the TVDB method manifests its capability not only in relativistic quantum chemistry but also for scattering and under the influence of strong external electronic and magnetic fields. The good accuracy in total energy with large basis sets and the good projection property encourage wider research on different molecules, with better functionals, and on small effects.

Patent DE10 2004 037 519 B4 “Sensor Process and Device for Determining a Physical Value“. A Proof of Concept

At present, a fraction of 0.1 - 0.2% of the patients undergoing surgery become aware during the process. The situation is referred to as anesthesia awareness and is obviously very traumatic for the person experiencing it. The reason for its occurrence is mostly an insufficient dosage of the narcotic Propofol combined with the incapability of the technology monitoring the depth of the patient’s anesthetic state to notice the patient becoming aware. A solution can be a highly sensitive and selective real time monitoring device for Propofol based on optical absorption spectroscopy. Its working principle has been postulated by Prof. Dr. habil. H. Hillmer and formulated in DE10 2004 037 519 B4, filed on Aug 30th, 2004. It consists of the exploitation of Intra Cavity Absorption effects in a two mode laser system. In this Dissertation, a two mode external cavity semiconductor laser, which has been developed previously to this work is enhanced and optimized to a functional sensor. Enhancements include the implementation of variable couplers into the system and the implementation of a collimator arrangement into which samples can be introduced. A sample holder and cells are developed and characterized with a focus on compatibility with the measurement approach. Further optimization concerns the overall performance of the system: scattering sources are reduced by re-splicing all fiber-to-fiber connections, parasitic cavities are eliminated by suppressing the Fresnel reflexes of all one fiber ends by means of optical isolators and wavelength stability of the system is improved by the implementation of thermal insulation to the Fiber Bragg Gratings (FBG). The final laser sensor is characterized in detail thermally and optically. Two separate modes are obtained at 1542.0 and 1542.5 nm, tunable in a range of 1nm each. Mode Full Width at Half Maximum (FWHM) is 0.06nm and Signal to Noise Ratio (SNR) is as high as 55 dB. Independent of tuning the two modes of the system can always be equalized in intensity, which is important as the delicacy of the intensity equilibrium is one of the main sensitivity enhancing effects formulated in DE10 2004 037 519 B4. For the proof of concept (POC) measurements the target substance Propofol is diluted in the solvents Acetone and DiChloroMethane (DCM), which have been investigated for compatibility with Propofol beforehand. Eight measurement series (two solvents, two cell lengths and two different mode spacings) are taken, which draw a uniform picture: mode intensity ratio responds linearly to an increase of Propofol in all cases. The slope of the linear response indicates the sensitivity of the system. The eight series are split up into two groups: measurements taken in long cells and measurements taken in short cells.

Untersuchungen zur Rolle von Isoformen katalytischer Untereinheiten der PKA

ZUSAMMENFASSUNG: Proteinkinasen übernehmen zentrale Aufgaben in der Signaltransduktion höherer Zellen. Dabei ist die cAMP-abhängige Proteinkinase (PKA) bezüglich ihrer Struktur und Funktion eine der am besten charakterisierten Proteinkinasen. Trotzdem ist wenig über direkte Interaktionspartner der katalytischen Untereinheiten (PKA-C) bekannt. In einem Split-Ubiquitin basiertem Yeast Two Hybrid- (Y2H-)System wurden potenzielle Interaktionspartner der PKA-C identifiziert. Als Bait wurden sowohl die humane Hauptisoform Cα (hCα) als auch die Proteinkinase X (PrKX) eingesetzt. Nach der Bestätigung der Funktionalität der PKA-C-Baitproteine, dem Nachweis der Expression und der Interaktion mit dem bekannten Interaktionspartner PKI wurde ein Y2H-Screen gegen eine Mausembryo-cDNA-Expressionsbibliothek durchgeführt. Von 2*10^6 Klonen wurden 76 Kolonien isoliert, die ein mit PrKX interagierendes Preyprotein exprimierten. Über die Sequenzierung der enthaltenen Prey-Vektoren wurden 25 unterschiedliche, potenzielle Interaktionspartner identifiziert. Für hCα wurden über 2*10^6 S. cerevisiae-Kolonien untersucht, von denen 1.959 positiv waren (1.663 unter erhöhter Stringenz). Über die Sequenzierung von ca. 10% der Klone (168) konnten Sequenzen für 67 verschiedene, potenzielle Interaktionspartner der hCα identifiziert werden. 15 der Preyproteine wurden in beiden Screens identifiziert. Die PKA-C-spezifische Wechselwirkung der insgesamt 77 Preyproteine wurde im Bait Dependency Test gegen largeT, ein Protein ohne Bezug zum PKA-System, untersucht. Aus den PKA-C-spezifischen Bindern wurden die löslichen Preyproteine AMY-1, Bax72-192, Fabp3, Gng11, MiF, Nm23-M1, Nm23-M2, Sssca1 und VASP256-375 für die weitere in vitro-Validierung ausgewählt. Die Interaktion von FLAG-Strep-Strep-hCα (FSS-hCα) mit den über Strep-Tactin aus der rekombinanten Expression in E. coli gereinigten One-STrEP-HA-Proteinen (SSHA-Proteine) wurde über Koimmunpräzipitation für SSHA-Fabp3, -Nm23-M1, -Nm23-M2, -Sssca1 und -VASP256-375 bestätigt. In SPR-Untersuchungen, für die hCα kovalent an die Oberfläche eines CM5-Sensorchips gekoppelt wurde, wurden die ATP/Mg2+-Abhängigkeit der Bindungen sowie differentielle Effekte der ATP-kompetitiven Inhibitoren H89 und HA-1077 untersucht. Freie hCα, die vor der Injektion zu den SSHA-Proteinen gegeben wurde, kompetierte im Gegensatz zu FSS-PrKX die Bindung an die hCα-Oberfläche. Erste kinetische Analysen lieferten Gleichgewichtsdissoziationskonstanten im µM- (SSHA-Fabp3, -Sssca1), nM- (SSHA-Nm23-M1, –M2) bzw. pM- (SSHA-VASP256-375) Bereich. In funktionellen Analysen konnte eine Phosphorylierung von SSHA-Sssca1 und VASP256-375 durch hCα und FSS-PrKX im Autoradiogramm nachgewiesen werden. SSHA-VASP256-375 zeigte zudem eine starke Inhibition von hCα im Mobility Shift-Assay. Dieser inhibitorische Effekt sowie die hohe Affinität konnten jedoch auf eine Kombination aus der Linkersequenz des Vektors und dem N-Terminus von VASP256-375 zurückgeführt werden. Über die Wechselwirkungen der hier identifizierten Interaktionspartner Fabp3, Nm23-M1 und Nm23-M2 mit hCα können in Folgeuntersuchungen neue PKA-Funktionen insbesondere im Herzen sowie während der Zellmigration aufgedeckt werden. Sssca1 stellt dagegen ein neues, näher zu charakterisierendes PKA-Substrat dar.

Biomass, quality traits and methane production of extensive grassland: biodiversity effects and sensor approaches

Energy policies around the world are mandating for a progressive increase in renewable energy production. Extensive grassland areas with low productivity and land use limitations have become target areas for sustainable energy production to avoid competition with food production on the limited available arable land resources and minimize further conversion of grassland into intensively managed energy cropping systems or abandonment. However, the high spatio-temporal variability in botanical composition and biochemical parameters is detrimental to reliable assessment of biomass yield and quality regarding anaerobic digestion. In an approach to assess the performance for predicting biomass using a multi-sensor combination including NIRS, ultra-sonic distance measurements and LAI-2000, biweekly sensor measurements were taken on a pure stand of reed canary grass (Phalaris aruninacea), a legume grass mixture and a diversity mixture with thirty-six species in an experimental extensive two cut management system. Different combinations of the sensor response values were used in multiple regression analysis to improve biomass predictions compared to exclusive sensors. Wavelength bands for sensor specific NDVI-type vegetation indices were selected from the hyperspectral data and evaluated for the biomass prediction as exclusive indices and in combination with LAI and ultra-sonic distance measurements. Ultrasonic sward height was the best to predict biomass in single sensor approaches (R² 0.73 – 0.76). The addition of LAI-2000 improved the prediction performance by up to 30% while NIRS barely improved the prediction performance. In an approach to evaluate broad based prediction of biochemical parameters relevant for anaerobic digestion using hyperspectral NIRS, spectroscopic measurements were taken on biomass from the Jena-Experiment plots in 2008 and 2009. Measurements were conducted on different conditions of the biomass including standing sward, hay and silage and different spectroscopic devices to simulate different preparation and measurement conditions along the process chain for biogas production. Best prediction results were acquired for all constituents at laboratory measurement conditions with dried and ground samples on a bench-top NIRS system (RPD > 3) with a coefficient of determination R2 < 0.9. The same biomass was further used in batch fermentation to analyse the impact of species richness and functional group composition on methane yields using whole crop digestion and pressfluid derived by the Integrated generation of solid Fuel and Biogas from Biomass (IFBB) procedure. Although species richness and functional group composition were largely insignificant, the presence of grasses and legumes in the mixtures were most determining factors influencing methane yields in whole crop digestion. High lignocellulose content and a high C/N ratio in grasses may have reduced the digestibility in the first cut material, excess nitrogen may have inhibited methane production in second cut legumes, while batch experiments proved superior specific methane yields of IFBB press fluids and showed that detrimental effects of the parent material were reduced by the technical treatment

Molekularbiologische Funktionsanalysen von Thioredoxinen aus Dictyostelium discoideum und Identifizierung neuer Interaktionspartner durch das Two-Hybrid-System

Thioredoxins are small, regulatory proteins with a mass of approximately 12 kDa and a characteristic conserved active center, which is represented in the pentapeptide trp-cys-gly-pro-cys. Up to now it is not possible to present a complete list of thioredoxin interaction partners because there is no predictable sequence in the target enzymes where thioredoxins can interact with. To get closer information about the functions and possible interaction partners of the three thioredoxins from the social soil amoeba Dictyostelium discoideum (DdTrx1 - 3) we have chosen two different strategies. In the first one the thioredoxin levels in the cell should changed by different mutants. But both the antisense technique as well as the creation of knock out mutants were not appropiate strategies in this case. Just an thioredoxin overexpressing mutant results in a developmental phenotype which allows some conclusions for possible functions of the thioredoxin in Dictyostelium discoideum. The second strategie was the two hybrid system where thioredoxin interactions partners can identified systematically. After a screening with a cDNA library from Dictyostelium 13 potential interaction partners could be detected, among them a ribonucleotid reductase, TRFA, two different cytochrome c oxidase subunits, filopodin, three ribosomal proteins, the elongationfactor 1a and the alcohol dehydrogenase from yeast. The verification of the interaction between thioredoxin and these two hybrid clones happened indirectly by a dobble mutant of thioredoxin 1, where the cysteines in the active center were replaced by redox-inactive serins. Further examinations of two choosen candidates resulted that the alcohol dehydrogenase from yeast is a thioredoxin-modululated enzym and that there is an interaction between the elongationfactor 1a and the thioredoxin 1 from Dictyostelium discoideum.

Modelling and simulation of a photovoltaic fuel cell hybrid system

A stand-alone power system is an autonomous system that supplies electricity to the user load without being connected to the electric grid. This kind of decentralized system is frequently located in remote and inaccessible areas. It is essential for about one third of the world population which are living in developed or isolated regions and have no access to an electricity utility grid. The most people live in remote and rural areas, with low population density, lacking even the basic infrastructure. The utility grid extension to these locations is not a cost effective option and sometimes technically not feasible. The purpose of this thesis is the modelling and simulation of a stand-alone hybrid power system, referred to as “hydrogen Photovoltaic-Fuel Cell (PVFC) hybrid system”. It couples a photovoltaic generator (PV), an alkaline water electrolyser, a storage gas tank, a proton exchange membrane fuel cell (PEMFC), and power conditioning units (PCU) to give different system topologies. The system is intended to be an environmentally friendly solution since it tries maximising the use of a renewable energy source. Electricity is produced by a PV generator to meet the requirements of a user load. Whenever there is enough solar radiation, the user load can be powered totally by the PV electricity. During periods of low solar radiation, auxiliary electricity is required. An alkaline high pressure water electrolyser is powered by the excess energy from the PV generator to produce hydrogen and oxygen at a pressure of maximum 30bar. Gases are stored without compression for short- (hourly or daily) and long- (seasonal) term. A proton exchange membrane (PEM) fuel cell is used to keep the system’s reliability at the same level as for the conventional system while decreasing the environmental impact of the whole system. The PEM fuel cell consumes gases which are produced by an electrolyser to meet the user load demand when the PV generator energy is deficient, so that it works as an auxiliary generator. Power conditioning units are appropriate for the conversion and dispatch the energy between the components of the system. No batteries are used in this system since they represent the weakest when used in PV systems due to their need for sophisticated control and their short lifetime. The model library, ISET Alternative Power Library (ISET-APL), is designed by the Institute of Solar Energy supply Technology (ISET) and used for the simulation of the hybrid system. The physical, analytical and/or empirical equations of each component are programmed and implemented separately in this library for the simulation software program Simplorer by C++ language. The model parameters are derived from manufacturer’s performance data sheets or measurements obtained from literature. The identification and validation of the major hydrogen PVFC hybrid system component models are evaluated according to the measured data of the components, from the manufacturer’s data sheet or from actual system operation. Then, the overall system is simulated, at intervals of one hour each, by using solar radiation as the primary energy input and hydrogen as energy storage for one year operation. A comparison between different topologies, such as DC or AC coupled systems, is carried out on the basis of energy point of view at two locations with different geographical latitudes, in Kassel/Germany (Europe) and in Cairo/Egypt (North Africa). The main conclusion in this work is that the simulation method of the system study under different conditions could successfully be used to give good visualization and comparison between those topologies for the overall performance of the system. The operational performance of the system is not only depending on component efficiency but also on system design and consumption behaviour. The worst case of this system is the low efficiency of the storage subsystem made of the electrolyser, the gas storage tank, and the fuel cell as it is around 25-34% at Cairo and 29-37% at Kassel. Therefore, the research for this system should be concentrated in the subsystem components development especially the fuel cell.

Technical and scale efficiency of cassava production system in Delta State, Nigeria: an application of Two-Stage DEA approach

The present study examines the level of pure technical and scale efficiencies of cassava production system including its sub-processes (that is production and processing stages) of 278 cassava farmers/processors from three regions of Delta State, Nigeria by applying Two-Stage Data Envelopment Analysis (DEA) approach. Results reveal that pure technical efficiency (PTE) is significantly lower at the production stage 0.41 vs 0.55 for the processing stage, but scale efficiency (SE) is high at both stages (0.84 and 0.87), implying that productivity can be improved substantially by reallocation of resources and adjusting operation size. The socio-economic determinants exert differential impacts on PTE and SE at each stage. Overall, education, experience and main occupation as farmer significantly improve SE while subsistence pressure reduces it. Extension contact significantly improves SE at the processing stage but reduces PTE and SE overall. Inverse size-PTE and size-SE relationships exist in cassava production system. In other words, large/medium farms are technically and scale inefficient. Gender gap exists in performance. Male farmers are technically efficient at processing stage but scale inefficient overall. Farmers in northern region are technically efficient. Investments in education, extension services and infrastructure are suggested as policy options to improve the cassava sector in Nigeria.