Das Einzugsgebiet der Fulda - Untersuchung der Methoden der Hochwasserstatistik im Zeichen des Klimawandels

Numerous studies have proven an effect of a probable climate change on the hydrosphere’s different subsystems. In the 21st century global and regional redistribution of water has to be expected and it is very likely that extreme weather phenomenon will occur more frequently. From a global view the flood situation will exacerbate. In contrast to these discoveries the classical approach of flood frequency analysis provides terms like “mean flood recurrence interval”. But for this analysis to be valid there is a need for the precondition of stationary distribution parameters which implies that the flood frequencies are constant in time. Newer approaches take into account extreme value distributions with time-dependent parameters. But the latter implies a discard of the mentioned old terminology that has been used up-to-date in engineering hydrology. On the regional scale climate change affects the hydrosphere in various ways. So, the question appears to be whether in central Europe the classical approach of flood frequency analysis is not usable anymore and whether the traditional terminology should be renewed. In the present case study hydro-meteorological time series of the Fulda catchment area (6930 km²), upstream of the gauging station Bonaforth, are analyzed for the time period 1960 to 2100. At first a distributed catchment area model (SWAT2005) is build up, calibrated and finally validated. The Edertal reservoir is regulated as well by a feedback control of the catchments output in case of low water. Due to this intricacy a special modeling strategy has been necessary: The study area is divided into three SWAT basin models and an additional physically-based reservoir model is developed. To further improve the streamflow predictions of the SWAT model, a correction by an artificial neural network (ANN) has been tested successfully which opens a new way to improve hydrological models. With this extension the calibration and validation of the SWAT model for the Fulda catchment area is improved significantly. After calibration of the model for the past 20th century observed streamflow, the SWAT model is driven by high resolution climate data of the regional model REMO using the IPCC scenarios A1B, A2, and B1, to generate future runoff time series for the 21th century for the various sub-basins in the study area. In a second step flood time series HQ(a) are derived from the 21st century runoff time series (scenarios A1B, A2, and B1). Then these flood projections are extensively tested with regard to stationarity, homogeneity and statistical independence. All these tests indicate that the SWAT-predicted 21st-century trends in the flood regime are not significant. Within the projected time the members of the flood time series are proven to be stationary and independent events. Hence, the classical stationary approach of flood frequency analysis can still be used within the Fulda catchment area, notwithstanding the fact that some regional climate change has been predicted using the IPCC scenarios. It should be noted, however, that the present results are not transferable to other catchment areas. Finally a new method is presented that enables the calculation of extreme flood statistics, even if the flood time series is non-stationary and also if the latter exhibits short- and longterm persistence. This method, which is called Flood Series Maximum Analysis here, enables the calculation of maximum design floods for a given risk- or safety level and time period.

Comparison of different methods in estimating potential evapotranspiration at Muda Irrigation Scheme of Malaysia

Evapotranspiration (ET) is a complex process in the hydrological cycle that influences the quantity of runoff and thus the irrigation water requirements. Numerous methods have been developed to estimate potential evapotranspiration (PET). Unfortunately, most of the reliable PET methods are parameter rich models and therefore, not feasible for application in data scarce regions. On the other hand, accuracy and reliability of simple PET models vary widely according to regional climate conditions. The objective of the present study was to evaluate the performance of three temperature-based and three radiation-based simple ET methods in estimating historical ET and projecting future ET at Muda Irrigation Scheme at Kedah, Malaysia. The performance was measured by comparing those methods with the parameter intensive Penman-Monteith Method. It was found that radiation based methods gave better performance compared to temperature-based methods in estimation of ET in the study area. Future ET simulated from projected climate data obtained through statistical downscaling technique also showed that radiation-based methods can project closer ET values to that projected by Penman-Monteith Method. It is expected that the study will guide in selecting suitable methods for estimating and projecting ET in accordance to availability of meteorological data.

Development of an ArcGIS extension to model urban climate factors

The possibility to develop automatically running models which can capture some of the most important factors driving the urban climate would be very useful for many planning aspects. With the help of these modulated climate data, the creation of the typically used “Urban Climate Maps” (UCM) will be accelerated and facilitated. This work describes the development of a special ArcGIS software extension, along with two support databases to achieve this functionality. At the present time, lacking comparability between different UCMs and imprecise planning advices going along with the significant technical problems of manually creating conventional maps are central issues. Also inflexibility and static behaviour are reducing the maps’ practicality. From experi-ence, planning processes are formed more productively, namely to implant new planning parameters directly via the existing work surface to map the impact of the data change immediately, if pos-sible. In addition to the direct climate figures, information of other planning areas (like regional characteristics / developments etc.) have to be taken into account to create the UCM as well. Taking all these requirements into consideration, an automated calculation process of urban climate impact parameters will serve to increase the creation of homogenous UCMs efficiently.

Applying Least Absolute Shrinkage Selection Operator and Akaike Information Criterion Analysis to Find the Best Multiple Linear Regression Models between Climate Indices and Components of Cow’s Milk

This study focuses on multiple linear regression models relating six climate indices (temperature humidity THI, environmental stress ESI, equivalent temperature index ETI, heat load HLI, modified HLI (HLI new), and respiratory rate predictor RRP) with three main components of cow’s milk (yield, fat, and protein) for cows in Iran. The least absolute shrinkage selection operator (LASSO) and the Akaike information criterion (AIC) techniques are applied to select the best model for milk predictands with the smallest number of climate predictors. Uncertainty estimation is employed by applying bootstrapping through resampling. Cross validation is used to avoid over-fitting. Climatic parameters are calculated from the NASA-MERRA global atmospheric reanalysis. Milk data for the months from April to September, 2002 to 2010 are used. The best linear regression models are found in spring between milk yield as the predictand and THI, ESI, ETI, HLI, and RRP as predictors with p-value < 0.001 and R2 (0.50, 0.49) respectively. In summer, milk yield with independent variables of THI, ETI, and ESI show the highest relation (p-value < 0.001) with R2 (0.69). For fat and protein the results are only marginal. This method is suggested for the impact studies of climate variability/change on agriculture and food science fields when short-time series or data with large uncertainty are available.