Preparation and applications of periodical gold nanoparticle arrays

Diese Arbeit beschäftigt sich mit der Herstellung und Anwendungen von periodischen Goldnanopartikel-Arrays (PPAs), die mit Hilfe von Nanosphären-Lithografie hergestellt wurden. In Abhängigkeit der verwendeten Nanosphären-Größe wurden dabei entweder kleine dreieckige Nanopartikel (NP) (bei Verwendung von Nanosphären mit einem Durchmesser von 330 nm) oder große dreieckige NPD sowie leicht gestreckte NP (bei Verwendung von Nanosphären mit einem Durchmesser von 1390 nm) hergestellt. Die Charakterisierung der PPAs erfolgte mit Hilfe von Rasterkraftmikroskopie, Rasterelektronenmikroskopie und optischer Spektroskopie. Die kleinen NP besitzen ein Achsverhältnis (AV) von 2,47 (Kantenlänge des NPs: (74+/-6) nm, Höhe: (30+/-4) nm. Die großen dreieckigen NP haben ein AV von 3 (Kantenlänge des NPs:(465+/-27) nm, Höhe: (1530+/-10) nm) und die leicht gestreckten NP (die aufgrund der Ausbildung von Doppelschichten ebenfalls auf der gleichen Probe erzeugt wurden) haben eine Länge von (364+/-16)nm, eine Breite von (150+/-20) nm und eine Höhe von (150+/-10)nm. Die optischen Eigenschaften dieser NP werden durch lokalisierte Oberflächenplasmon-Polariton Resonanzen (LPPRs) dominiert, d.h. von einem eingestrahlten elektromagnetischen Feld angeregte kollektive Schwingungen der Leitungsbandelektronen. In dieser Arbeit wurden drei signifikante Herausforderungen für Plasmonik-Anwendungen bearbeitet, welche die einzigartigen optischen Eigenschaften dieser NP ausnutzen. Erstens wurden Ergebnisse der selektiven und präzisen Größenmanipulation und damit einer Kontrolle der interpartikulären Abstände von den dreieckigen Goldnanopartikel mit Hilfe von ns-gepulstem Laserlicht präsentiert. Die verwendete Methode basiert hierbei auf der Größen- und Formabhängigkeit der LPPRs der NP. Zweitens wurde die sensorischen Fähigkeiten von Gold-NP ausgenutzt, um die Bildung von molekularen Drähten auf den PPAs durch schrittweise Zugabe von unterschiedlichen molekularen Spezies zu untersuchen. Hierbei wurde die Verschiebung der LSPPR in den optischen Spektren dazu ausgenutzt, die Bildung der Nanodrähte zu überwachen. Drittens wurden Experimente vorgestellt, die sich die lokale Feldverstärkung von NP zu nutze machen, um eine hochgeordnete Nanostrukturierung von Oberflächen mittels fs-gepulstem Laserlicht zu bewerkstelligen. Dabei zeigt sich, dass neben der verwendeten Fluenz die Polarisationsrichtung des eingestrahlten Laserlichts in Bezug zu der NP-Orientierung sowie die Größe der NP äußerst wichtige Parameter für die Nanostrukturierung darstellen. So konnten z.B. Nanolöcher erzeugt werden, die bei höheren Fluenzen zu Nanogräben und Nanokanälen zusammen wuchsen. Zusammengefasst lässt sich sagen, dass die in dieser Arbeit gewonnen Ergebnisse von enormer Wichtigkeit für weitere Anwendungen sind.

Systematics and evolution of the genus Deuterocohnia Mez (Bromeliaceae)

The present study investigates the systematics and evolution of the Neotropical genus Deuterocohnia Mez (Bromeliaceae). It provides a comprehensive taxonomic revision as well as phylogenetic analyses based on chloroplast and nuclear DNA sequences and presents a hypothesis on the evolution of the genus. A broad morphological, anatomical, biogeographical and ecological overview of the genus is given in the first part of the study. For morphological character assessment more than 700 herbarium specimens from 39 herbaria as well as living plant material in the field and in the living collections of botanical gardens were carefully examined. The arid habitats, in which the species of Deuterocohnia grow, are reflected by the morphological and anatomical characters of the species. Important characters for species delimitation were identified, like the length of the inflorescence, the branching order, the density of flowers on partial inflorescences, the relation of the length of the primary bracts to that of the partial inflorescence, the sizes of floral bracts, sepals and petals, flower colour, the presence or absence of a pedicel, the curvature of the stamina and the petals during anthesis. After scrutinizing the nomenclatural history of the taxa belonging to Deuterocohnia – including the 1992 syonymized genus Abromeitiella – 17 species, 4 subspecies and 4 varieties are accepted in the present revision. Taxonomic changes were made in the following cases: (I) New combinations: A. abstrusa (A. Cast.) N. Schütz is re-established – as defined by Castellanos (1931) – and transfered to D. abstrusa; D. brevifolia (Griseb.) M.A. Spencer & L.B. Sm. includes accessions of the former D. lorentziana (Mez) M.A. Spencer & L.B. Sm., which are not assigned to D. abstrusa; D. bracteosa W. Till is synonymized to D. strobilifera Mez; D. meziana Kuntze ex Mez var. carmineo-viridiflora Rauh is classified as a subspecies of D. meziana (ssp. carmineo-viridiflora (Rauh) N. Schütz); D. pedicellata W. Till is classified as a subspecies of D. meziana (ssp. pedicellata (W. Till) N. Schütz); D. scapigera (Rauh & L. Hrom.) M.A. Spencer & L.B. Sm ssp. sanctae-crucis R. Vásquez & Ibisch is classified as a species (D. sanctae-crucis (R. Vásquez & Ibisch) N. Schütz); (II) New taxa: a new subspecies of D. meziana Kuntze ex Mez is established; a new variety of D. scapigera is established; (the new taxa will be validly published elsewhere); (III) New type: an epitype for D. longipetala was chosen. All other species were kept according to Spencer and Smith (1992) or – in the case of more recently described species – according to the protologue. Beside the nomenclatural notes and the detailed descriptions, information on distribution, habitat and ecology, etymology and taxonomic delimitation is provided for the genus and for each of its species. An key was constructed for the identification of currently accepted species, subspecies and varieties. The key is based on easily detectable morphological characters. The former synonymization of the genus Abromeitiella into Deuterocohnia (Spencer and Smith 1992) is re-evalutated in the present study. Morphological as well as molecular investigations revealed Deuterocohnia incl. Abromeitiella as being monophyletic, with some indications that a monophyletic Abromeitiella lineage arose from within Deuterocohnia. Thus the union of both genera is confirmed. The second part of the present thesis describes and discusses the molecular phylogenies and networks. Molecular analyses of three chloroplast intergenic spacers (rpl32-trnL, rps16-trnK, trnS-ycf3) were conducted with a sample set of 119 taxa. This set included 103 Deuterocohnia accessions from all 17 described species of the genus and 16 outgroup taxa from the remainder of Pitcairnioideae s.str. (Dyckia (8 sp.), Encholirium (2 sp.), Fosterella (4 sp.) and Pitcairnia (2 sp.)). With its high sampling density, the present investigation by far represents the most comprehensive molecular study of Deuterocohnia up till now. All data sets were analyzed separately as well as in combination, and various optimality criteria for phylogenetic tree construction were applied (Maximum Parsimony, Maximum Likelihood, Bayesian inferences and the distance method Neighbour Joining). Congruent topologies were generally obtained with different algorithms and optimality criteria, but individual clades received different degrees of statistical support in some analyses. The rps16-trnK locus was the most informative among the three spacer regions examined. The results of the chloroplast DNA analyses revealed a highly supported paraphyly of Deuterocohnia. Thus, the cpDNA trees divide the genus into two subclades (A and B), of which Deuterocohnia subclade B is sister to the included Dyckia and Encholirium accessions, and both together are sister to Deuterocohnia subclade A. To further examine the relationship between Deuterocohnia and Dyckia/Encholirium at the generic level, two nuclear low copy markers (PRK exon2-5 and PHYC exon1) were analysed with a reduced taxon set. This set included 22 Deuterocohnia accessions (including members of both cpDNA subclades), 2 Dyckia, 2 Encholirium and 2 Fosterella species. Phylogenetic trees were constructed as described above, and for comparison the same reduced taxon set was also analysed at the three cpDNA data loci. In contrast to the cpDNA results, the nuclear DNA data strongly supported the monophyly of Deuterocohnia, which takes a sister position to a clade of Dyckia and Encholirium samples. As morphology as well as nuclear DNA data generated in the present study and in a former AFLP analysis (Horres 2003) all corroborate the monophyly of Deuterocohnia, the apparent paraphyly displayed in cpDNA analyses is interpreted to be the consequence of a chloroplast capture event. This involves the introgression of the chloroplast genome from the common ancestor of the Dyckia/ Encholirium lineage into the ancestor of Deuterocohnia subclade B species. The chloroplast haplotypes are not species-specific in Deuterocohnia. Thus, one haplotype was sometimes shared by several species, where the same species may harbour different haplotypes. The arrangement of haplotypes followed geographical patterns rather than taxonomic boundaries, which may indicate some residual gene flow among populations from different Deuteroccohnia species. Phenotypic species coherence on the background of ongoing gene flow may then be maintained by sets of co-adapted alleles, as was suggested by the porous genome concept (Wu 2001, Palma-Silva et al. 2011). The results of the present study suggest the following scenario for the evolution of Deuterocohnia and its species. Deuterocohnia longipetala may be envisaged as a representative of the ancestral state within the genus. This is supported by (1) the wide distribution of this species; (2) the overlap in distribution area with species of Dyckia; (3) the laxly flowered inflorescences, which are also typical for Dyckia; (4) the yellow petals with a greenish tip, present in most other Deuterocohnia species. The following six extant lineages within Deuterocohnia might have independently been derived from this ancestral state with a few changes each: (I) D. meziana, D. brevispicata and D. seramisiana (Bolivia, lowland to montane areas, mostly reddish-greenish coloured, very laxly to very densely flowered); (II) D. strobilifera (Bolivia, high Andean mountains, yellow flowers, densely flowered); (III) D. glandulosa (Bolivia, montane areas, yellow-greenish flowers, densely flowered); (IV) D. haumanii, D. schreiteri, D. digitata, and D. chrysantha (Argentina, Chile, E Andean mountains and Atacama desert, yellow-greenish flowers, densely flowered); (V) D. recurvipetala (Argentina, foothills of the Andes, recurved yellow flowers, laxly flowered); (VI) D. gableana, D. scapigera, D. sanctae-crucis, D. abstrusa, D. brevifolia, D. lotteae (former Abromeitiella species, Bolivia, Argentina, higher Andean mountains, greenish-yellow flowers, inflorescence usually simple). Originating from the lower montane Andean regions, at least four lineages of the genus (I, II, IV, VI) adapted in part to higher altitudes by developing densely flowered partial inflorescences, shorter flowers and – in at least three lineages (II, IV, VI) – smaller rosettes, whereas species spreading into the lowlands (I, V) developed larger plants, laxly flowered, amply branched inflorescences and in part larger flowers (I).

First-principles electronic theory of non-collinear magnetic order in transition-metal nanowires

The structural, electronic and magnetic properties of one-dimensional 3d transition-metal (TM) monoatomic chains having linear, zigzag and ladder geometries are investigated in the frame-work of first-principles density-functional theory. The stability of long-range magnetic order along the nanowires is determined by computing the corresponding frozen-magnon dispersion relations as a function of the 'spin-wave' vector q. First, we show that the ground-state magnetic orders of V, Mn and Fe linear chains at the equilibrium interatomic distances are non-collinear (NC) spin-density waves (SDWs) with characteristic equilibrium wave vectors q that depend on the composition and interatomic distance. The electronic and magnetic properties of these novel spin-spiral structures are discussed from a local perspective by analyzing the spin-polarized electronic densities of states, the local magnetic moments and the spin-density distributions for representative values q. Second, we investigate the stability of NC spin arrangements in Fe zigzag chains and ladders. We find that the non-collinear SDWs are remarkably stable in the biatomic chains (square ladder), whereas ferromagnetic order (q =0) dominates in zigzag chains (triangular ladders). The different magnetic structures are interpreted in terms of the corresponding effective exchange interactions J(ij) between the local magnetic moments μ(i) and μ(j) at atoms i and j. The effective couplings are derived by fitting a classical Heisenberg model to the ab initio magnon dispersion relations. In addition they are analyzed in the framework of general magnetic phase diagrams having arbitrary first, second, and third nearest-neighbor (NN) interactions J(ij). The effect of external electric fields (EFs) on the stability of NC magnetic order has been quantified for representative monoatomic free-standing and deposited chains. We find that an external EF, which is applied perpendicular to the chains, favors non-collinear order in V chains, whereas it stabilizes the ferromagnetic (FM) order in Fe chains. Moreover, our calculations reveal a change in the magnetic order of V chains deposited on the Cu(110) surface in the presence of external EFs. In this case the NC spiral order, which was unstable in the absence of EF, becomes the most favorable one when perpendicular fields of the order of 0.1 V/Å are applied. As a final application of the theory we study the magnetic interactions within monoatomic TM chains deposited on graphene sheets. One observes that even weak chain substrate hybridizations can modify the magnetic order. Mn and Fe chains show incommensurable NC spin configurations. Remarkably, V chains show a transition from a spiral magnetic order in the freestanding geometry to FM order when they are deposited on a graphene sheet. Some TM-terminated zigzag graphene-nanoribbons, for example V and Fe terminated nanoribbons, also show NC spin configurations. Finally, the magnetic anisotropy energies (MAEs) of TM chains on graphene are investigated. It is shown that Co and Fe chains exhibit significant MAEs and orbital magnetic moments with in-plane easy magnetization axis. The remarkable changes in the magnetic properties of chains on graphene are correlated to charge transfers from the TMs to NN carbon atoms. Goals and limitations of this study and the resulting perspectives of future investigations are discussed.

Adsorption kinetic investigations of phthalocyanine derivatives self assembled monolayers (SAMs) on gold: Temperature influence on the SAM formation process and quality

The ordered nano-structured surfaces, like self-assembled monolayers (SAMs) are of a great scientific interest, due to the low cost, simplicity, and versatility of this method. SAMs found numerous of applications in molecular electronics, biochemistry and optical devices. Phthalocyanine (Pc) complexes are of particular interest for the SAM preparation. These molecules exhibit fascinating physical properties and are chemically and thermally stable. Moreover their complex structure is advantageous for the fabrication of switchable surfaces. In this work the adsorption process of Pcs derivatives, namely, subphthalocyanines (SubPcB) and terbium (2TbPc) sandwich complexes on gold has been investigated. The influence of the molecular concentration, chain length of peripheral groups, and temperature on the film formation process has been examined using a number of techniques. The SAMs formation process has been followed in situ and in real time by means of second harmonic generation (SHG) and surface plasmon resonance (SPR) spectroscopy. To investigate the quality of the SAMs prepared at different temperatures atomic force microscopy (AFM) and X-Ray photoelectron spectroscopy (XPS)measurements were performed. Valuable information about SubPcB and 2TbPc adsorbtion process has been obtained in the frame of this work. The kinetic data, obtained with SHG and SPR, shows the best conformance with the first order Langmuir kinetic model. Comparing SHG and SPR results, it has been found, that the film formation occurs faster than the formation of chemical bonds. Such, the maximum amount of molecules on the surface is reached after 6 min for SubPcB and 30 min for 2TbPc. However, at this time the amount of formed chemicals bonds is only 10% and 40% for SubPcB and 2TbPc, respectively. The most intriguing result, among others, was obtained at T = 2 °C, where the formation of the less dense SAMs have been detected with SHG.However, analyzing XPS and AFM data, it has been revealed, that there is the same amount of molecules on the surface at both temperature T = 2 °C, and T = 21 °C, but the amount of formed chemicals bond is different. At T = 2 °C molecules form aggregates, therefore many of available anchor groups stay unattached.