The Corticiaceae (Basidiomycetes) in Taiwan

Geographically, Taiwan is an Island and situated in the northeast of Asia, on the western side of the Pacific Basin, at the southeast of main China, south of Japan, and north of the Philippines. The main topographic character is the longitudinally oriented mountainous area. More than 200 peaks rise above 3000 m. They departed Taiwan into two lowland areas, an eastern and western plain. Taiwan is departed into subtropical (north area) and tropical zone (south area), which have a warm and humid climate, due to the Tropic of Cancer passing through. The average annual temperature in the lowland amounts to 28°C (7~38°C). The temperate climate also presents in the mountainous areas. The tropical typhoons usually come in summer and bring heavy rain, while the monsoon seasons have an important effect on the regional rainfall distribution. The mean annual rainfall of Taiwan is about 2600 mm (1000~6700 mm); the mountainous areas receive more rain than the lowlands. In Taiwan, according to different temperature and vegetation, the ecological environments were given rise to vertical biotic zonations, and form five major types: highland snowfield, highland meadow, coniferous forest, deciduous forest, and tropical forest. Six National Parks in Taiwan are located in the mountainous areas, in the north, the south, and on Jinmen Island. The National Parks represent about 8.4% of the country area. In this study, the collection sites are situated in Yangmingshan, Shei-Pa, Yushan, and Kenting National Park. Due to the island isolation, the proportions of endemic species are great in Taiwan, which also presents a high biodiversity. There are 4255 species of vascular plants including 1133 endemic. 5936 species in 1276 genera of fungi are hitherto reported in Taiwan. Among them, 233 Corticiaceae species were recorded, over one third (79 species) of them are known only from Taiwan. The first fungal report in Taiwan is about Phytophthora cyperi, published by the Japanese researcher T. Kawakami in 1904. Therefore, the history of research about fungi in Taiwan is more than one hundred years old. An eminent Japanese mycologist K. Sawada made an intensive survey from 1919 to 1959, and reported 2464 fungi species in his eleven volumes of “Descriptive Catalogue of Formosan Fungi”. However, only a few species (21 species in 9 genera) of Corticiaceae were recorded. From 1973, Chen and Lin resumed the study on Corticiaceae, and also some other foreign mycologists contributed for this field after 1980. The German research group lead by Franz Oberwinkler from Tübingen University collected in Taiwan several times. They published a number of new species and new records. Since 1989, S. H. Wu, a Taiwanese mycologist, has published a great amount of reports on corticioid fungi from Taiwan. Corticioid fungi were made up by the large and heterogeneous unnatural family Corticiaceae and other resupinate fungi belonging to other natural families in the Agaricomycetes. Molecular studies have shown that corticioid genera are distributed across all major clades of Agaricomycetes indicating that the corticioid fungi represent a polyphyletic group. They have resupinate fruitbodies and similar habitats. Species are characterized by simple fruitbody, more or less effused, and present smooth, porioid, grandinioid to odontioid hymenial surface. The fruitbodies are differently colored and usually soft to tough. Most of the Corticiaceae species are wood-saprobic organisms and gain the energy from the decomposing of wood-substrate such as cellulose or lignin. Materials for this study were collected by the author and other mycologists in Taiwan during surveys in April and May 1996, and March 2007, using the spring season with its high humidity and warm climate which are optimal conditions for the development of fungi. For assembling, the convenience sampling method was used in this study. This approach was chosen because it enables to detect a high biodiversity in a short time, and also to find species with rare or patchy distribution. The collecting sites from the North to the South include four National Parks and some preserved forests. They cover many different habitats such as low lands and high mountains. Fresh specimens were dried and analysed with a light microscope. 265 specimens belonging to Corticiaceae were studied in this research. Among them, 50 species in 21 genera including 11 new records and 10 new species were described with text and drawing. Four new species are belonging to Hyphodontia (H. sp. nov. 1, H. sp. nov. 2, H. sp. nov. 3, and H. sp. nov. 4), four to Schizopora (Sch. sp. nov. 1, Sch. sp. nov. 2, Sch. sp. nov. 3, and Sch. sp. nov. 4), one in Trechispora (T. sp. nov. 1), and one in Tubulicrinis (T. sp. nov. 1). Species recorded as new are Aleurodiscus amorphus, Botryohypochnus isabellinus, Hyphodontia cineracea, Hyphodontia palmae, Hypochnicium vellereum, Merulius tremellosus, Metulodontia nivea, Paullicorticium ansatum, Phlebia radiata, Phlebiella ardosiaca, and Xylobolus frustulatus. Besides, Botryohypochnus, Merulius, Metulodontia, Paullicorticium, and Xylobolus are also newly recorded genera in Taiwan. The genus Hyphodontia presents the highest diversity with 20 out of 50 species recorded. The second important genus is Hyphoderma, however with only 5 species. This indicates that Hyphodontia and Hyphoderma have a higher ability to develop in variable environments and approximately shows the predominance of these two genera in Taiwanese Corticiaceae. There are 11 new records out of the 50 species recorded, representing 22%. Some species, e.g. Hypochnicium vellereum and Paullicorticium ansatum were in the past recorded only in Europe and North America with cold and temperate climate. The samples of them are for the first time found in the subtropical belt, and display some difference from those of temperate regions. These collections should be molecularly investigated to clarify if they represent the same species of temperate areas. Patchily distributed species, for example Phlebiella ardosiaca, previously known only in Europe, and Hyphodontia palmae collected only in Brazil, were first recorded in different continents. Two possibilities are indicated by these new records: they are worldwide species but very rare to be found, or the Taiwanese specimens are taxonomically different. More survey from other continents and molecular study for these collections should be done in the future to solve this question. The distribution of Corticiaceae in Taiwan presents the variations in the north, central, and south areas and shows the diversity in lowlands and high mountains. The results of this study provide the evidence that the temperate Corticiaceae species displays a wider distribution. Subtropical and tropical taxa probably have also high dispersal capacities, and could possibly be found in the future in neighboring areas such as China, Japan, Korea or South Asia, but this needs further researches. In the total of 50 species, 10 new taxa were described in this study, giving about 20%. Some new species (e.g. Hyphodontia sp. 1, Hyphodontia sp. 2, and Hyphodontia sp. 3) are very similar to known species (Hyphodontia sambuci and Hyphodontia formosana), and the distinctive characters of Schizopora sp. nov. 1 are intermediate between those of Schizopora paradoxa and Hyphodontia flavipora. Thus, these small differences between the new and known species, suggest that the speciation occurred when the fungi migrated into Taiwan, due to the high diversity of environment, and amounts of the endemic plants. Taiwan is an intermediate place for the south (tropical) fungal species to migrate and adapt to north (temperate) regions. The middle and high altitude environments in Taiwan offer good conditions for the fungal speciation and possibly the occurrence of physiological changes to adapt to the temperate climate. Thus Taiwan has an important position for the biogeography of Asia mycobiota. 5936 known species in Taiwan represent about only 20% of the estimated number (24000) of Taiwanese fungal taxa. In this study, the findings (22% new records and 20% new species) indicate that amounts of unknown fungi species are expected in Taiwan. The lack of knowledge indicates that many new species are awaiting description, and fungal survey in Taiwan remains in a Pioneer phase. The last three wide surveys of Corticiaceae researches took place 20 years before this study (Chen & Lin 1977, Lin & Chen 1989, Wu 1990). After previous important contributions, the present taxonomic study comprising 21 genera is the most extensive on Corticiaceae of Taiwan.

Einfluss der Führung des Trocknungsprozesses auf den Trocknungsverlauf und die Produkteigenschaften empfindlicher biologischer Güter

Die Konvektionstrocknung ist eine der ältesten Methoden zur Konservierung von Lebensmitteln. Es ist bekannt, dass Agrarprodukte temperaturempfindlich sind. Bei Überhitzung erleiden sie chemische und physikalische Veränderungen, die ihre Qualität vermindern. In der industriellen Praxis wird die Konvektionstrocknung in der Regel auf Grundlage empirisch ermittelter Werte durchgeführt, welche die Produkttemperatur nicht berücksichtigen. Es ist deshalb nicht sichergestellt, ob der Prozess optimal oder auch nur gut betrieben wird. Inhalt dieser Arbeit ist ein Vergleich der klassischen einstufigen Konvektionstrocknung mit einer Prozessführungsstrategie bei der die Produkttemperatur als Regelgröße eingeführt wird. Anhand der Untersuchung des Trocknungsverhaltens von Äpfeln werden die beiden Verfahren analysiert, die erhaltenen Ergebnisse miteinander verglichen und daraus optimierte Trocknungsbedingungen abgeleitet. Die für dieses Projekt entwickelte Prozessanlage erlaubt die simultane Untersuchung sämtlicher wesentlicher Temperaturen, der Gewichtsveränderung und der optischen Qualitätskriterien. Gleichzeitig ist es möglich, entweder die Lufttemperatur oder die Temperatur des Produktes zur regeln, während die jeweils andere Größe als Messwert erfasst wird. Es kann weiterhin zwischen Durch- und Überströmung gewählt werden.

Quality oriented drying of Lemon Balm (Melissa officinalis L.)

Heilkräuter sind während des Trocknungsprozesses zahlreichen Einflüssen ausgesetzt, welche die Qualität des Endproduktes entscheidend beeinflussen. Diese Forschungsarbeit beschäftigt sich mit der Trocknung von Zitronenmelisse (Melissa officinalis .L) zu einem qualitativ hochwertigen Endprodukt. Es werden Strategien zur Trocknung vorgeschlagen, die experimentelle und mathematische Aspekte mit einbeziehen, um bei einer adäquaten Produktivität die erforderlichen Qualitätsmerkmale im Hinblick auf Farbeänderung und Gehalt an ätherischen Ölen zu erzielen. Getrocknete Zitronenmelisse kann zurzeit, auf Grund verschiedener Probleme beim Trocknungsvorgang, den hohen Qualitätsanforderungen des Marktes nicht immer genügen. Es gibt keine standardisierten Informationen zu den einzelnen und komplexen Trocknungsparametern. In der Praxis beruht die Trocknung auf Erfahrungswerten, bzw. werden Vorgehensweisen bei der Trocknung anderer Pflanzen kopiert, und oftmals ist die Trocknung nicht reproduzierbar, oder beruht auf subjektiven Annäherungen. Als Folge dieser nicht angepassten Wahl der Trocknungsparameter entstehen oftmals Probleme wie eine Übertrocknung, was zu erhöhten Bruchverlusten der Blattmasse führt, oder eine zu geringe Trocknung, was wiederum einen zu hohen Endfeuchtegehalt im Produkt zur Folge hat. Dies wiederum mündet zwangsläufig in einer nicht vertretbaren Farbänderung und einen übermäßigen Verlust an ätherischen Ölen. Auf Grund der unterschiedlichen thermischen und mechanischen Eigenschaften von Blättern und Stängel, ist eine ungleichmäßige Trocknung die Regel. Es wird außerdem eine unnötig lange Trocknungsdauer beobachtet, die zu einem erhöhten Energieverbrauch führt. Das Trocknen in solaren Tunneln Trocknern bringt folgendes Problem mit sich: wegen des ungeregelten Strahlungseinfalles ist es schwierig die Trocknungstemperatur zu regulieren. Ebenso beeinflusst die Strahlung die Farbe des Produktes auf Grund von photochemischen Reaktionen. Zusätzlich erzeugen die hohen Schwankungen der Strahlung, der Temperatur und der Luftfeuchtigkeit instabile Bedingungen für eine gleichmäßige und kontrollierbare Trocknung. In Anbetracht der erwähnten Probleme werden folgende Forschungsschwerpunkte in dieser Arbeit gesetzt: neue Strategien zur Verbesserung der Qualität werden entwickelt, mit dem Ziel die Trocknungszeit und den Energieverbrauch zu verringern. Um eine Methodik vorzuschlagen, die auf optimalen Trocknungsparameter beruht, wurden Temperatur und Luftfeuchtigkeit als Variable in Abhängigkeit der Trocknungszeit, des ätherischer Ölgehaltes, der Farbänderung und der erforderliche Energie betrachtet. Außerdem wurden die genannten Parametern und deren Auswirkungen auf die Qualitätsmerkmale in solaren Tunnel Trocknern analysiert. Um diese Ziele zu erreichen, wurden unterschiedliche Ansätze verfolgt. Die Sorption-Isothermen und die Trocknungskinetik von Zitronenmelisse und deren entsprechende Anpassung an verschiedene mathematische Modelle wurden erarbeitet. Ebenso wurde eine alternative gestaffelte Trocknung in gestufte Schritte vorgenommen, um die Qualität des Endproduktes zu erhöhen und gleichzeitig den Gesamtenergieverbrauch zu senken. Zusätzlich wurde ein statistischer Versuchsplan nach der CCD-Methode (Central Composite Design) und der RSM-Methode (Response Surface Methodology) vorgeschlagen, um die gewünschten Qualitätsmerkmalen und den notwendigen Energieeinsatz in Abhängigkeit von Lufttemperatur und Luftfeuchtigkeit zu erzielen. Anhand der gewonnenen Daten wurden Regressionsmodelle erzeugt, und das Verhalten des Trocknungsverfahrens wurde beschrieben. Schließlich wurde eine statistische DOE-Versuchsplanung (design of experiments) angewandt, um den Einfluss der Parameter auf die zu erzielende Produktqualität in einem solaren Tunnel Trockner zu bewerten. Die Wirkungen der Beschattung, der Lage im Tunnel, des Befüllungsgrades und der Luftgeschwindigkeit auf Trocknungszeit, Farbänderung und dem Gehalt an ätherischem Öl, wurde analysiert. Ebenso wurden entsprechende Regressionsmodelle bei der Anwendung in solaren Tunneltrocknern erarbeitet. Die wesentlichen Ergebnisse werden in Bezug auf optimale Trocknungsparameter in Bezug auf Qualität und Energieverbrauch analysiert.

Using a Double-pass solar drier for drying of bamboo shoots

Three different drying methods, a forced convection double-pass solar drier (DPSD), typical cabinet type natural convection solar drier (CD) and traditional open-sun drying (OSD) were used for draying of bamboo shoots in central Vietnam. During drying the operational parameters such as drying temperature, relative humidity, air velocity, insolation and water evaporation have been recorded hourly. The mean drying temperatures and relative humidity in the drying chamber were 55.2°C, 23.7%; 47.5°C, 37,6%; 36.2°C, 47.8% in DPSD, CD and OSD, respectively. The mean global radiation during all experimental runs was 670 Wm^−2. The result also shows that fastest drying process was occurred in DPSD where the falling-rate period was achieved after 7 hours, in change to OSD where it took 16 hours. The overall drying efficiency was 23.11%, 15.83% and 9.73% in case of DPSD, CD and OSD, respectively. Although the construction cost of DPSD was significantly higher than in CD, the drying costs per one kilogram of bamboo shoots were by 42.8% lower in case of DPSD as compared to CD. Double-pass solar drier was found to be technically and economically suitable for drying of bamboo shoots under the specific conditions in central Vietnam and in all cases, the use of this drier led to considerable reduction in drying time in comparison to traditional open-sun drying.

Optimization of Processing Technology for Commercial Drying of Bananas (Matooke)

Summary - Cooking banana is one of the most important crops in Uganda; it is a staple food and source of household income in rural areas. The most common cooking banana is locally called matooke, a Musa sp triploid acuminate genome group (AAA-EAHB). It is perishable and traded in fresh form leading to very high postharvest losses (22-45%). This is attributed to: non-uniform level of harvest maturity, poor handling, bulk transportation and lack of value addition/processing technologies, which are currently the main challenges for trade and export, and diversified utilization of matooke. Drying is one of the oldest technologies employed in processing of agricultural produce. A lot of research has been carried out on drying of fruits and vegetables, but little information is available on matooke. Drying of matooke and milling it to flour extends its shelf-life is an important means to overcome the above challenges. Raw matooke flour is a generic flour developed to improve shelf stability of the fruit and to find alternative uses. It is rich in starch (80 - 85%db) and subsequently has a high potential as a calorie resource base. It possesses good properties for both food and non-food industrial use. Some effort has been done to commercialize the processing of matooke but there is still limited information on its processing into flour. It was imperative to carry out an in-depth study to bridge the following gaps: lack of accurate information on the maturity window within which matooke for processing into flour can be harvested leading to non-uniform quality of matooke flour; there is no information on moisture sorption isotherm for matooke from which the minimum equilibrium moisture content in relation to temperature and relative humidity is obtainable, below which the dry matooke would be microbiologically shelf-stable; and lack of information on drying behavior of matooke and standardized processing parameters for matooke in relation to physicochemical properties of the flour. The main objective of the study was to establish the optimum harvest maturity window and optimize the processing parameters for obtaining standardized microbiologically shelf-stable matooke flour with good starch quality attributes. This research was designed to: i) establish the optimum maturity harvest window within which matooke can be harvested to produce a consistent quality of matooke flour, ii) establish the sorption isotherms for matooke, iii) establish the effect of process parameters on drying characteristics of matooke, iv) optimize the drying process parameters for matooke, v) validate the models of maturity and optimum process parameters and vi) standardize process parameters for commercial processing of matooke. Samples were obtained from a banana plantation at Presidential Initiative on Banana Industrial Development (PIBID), Technology Business Incubation Center (TBI) at Nyaruzunga – Bushenyi in Western Uganda. A completely randomized design (CRD) was employed in selecting the banana stools from which samples for the experiments were picked. The cultivar Mbwazirume which is soft cooking and commonly grown in Bushenyi was selected for the study. The static gravitation method recommended by COST 90 Project (Wolf et al., 1985), was used for determination of moisture sorption isotherms. A research dryer developed for this research. All experiments were carried out in laboratories at TBI. The physiological maturity of matooke cv. mbwazirume at Bushenyi is 21 weeks. The optimum harvest maturity window for commercial processing of matooke flour (Raw Tooke Flour - RTF) at Bushenyi is between 15-21 weeks. The finger weight model is recommended for farmers to estimate harvest maturity for matooke and the combined model of finger weight and pulp peel ratio is recommended for commercial processors. Matooke isotherms exhibited type II curve behavior which is characteristic of foodstuffs. The GAB model best described all the adsorption and desorption moisture isotherms. For commercial processing of matooke, in order to obtain a microbiologically shelf-stable dry product. It is recommended to dry it to moisture content below or equal to 10% (wb). The hysteresis phenomenon was exhibited by the moisture sorption isotherms for matooke. The isoteric heat of sorption for both adsorptions and desorption isotherms increased with decreased moisture content. The total isosteric heat of sorption for matooke: adsorption isotherm ranged from 4,586 – 2,386 kJ/kg and desorption isotherm from 18,194– 2,391 kJ/kg for equilibrium moisture content from 0.3 – 0.01 (db) respectively. The minimum energy required for drying matooke from 80 – 10% (wb) is 8,124 kJ/kg of water removed. Implying that the minimum energy required for drying of 1 kg of fresh matooke from 80 - 10% (wb) is 5,793 kJ. The drying of matooke takes place in three steps: the warm-up and the two falling rate periods. The drying rate constant for all processing parameters ranged from 5,793 kJ and effective diffusivity ranged from 1.5E-10 - 8.27E-10 m2/s. The activation energy (Ea) for matooke was 16.3kJ/mol (1,605 kJ/kg). Comparing the activation energy (Ea) with the net isosteric heat of sorption for desorption isotherm (qst) (1,297.62) at 0.1 (kg water/kg dry matter), indicated that Ea was higher than qst suggesting that moisture molecules travel in liquid form in matooke slices. The total color difference (ΔE*) between the fresh and dry samples, was lowest for effect of thickness of 7 mm, followed by air velocity of 6 m/s, and then drying air temperature at 70˚C. The drying system controlled by set surface product temperature, reduced the drying time by 50% compared to that of a drying system controlled by set air drying temperature. The processing parameters did not have a significant effect on physicochemical and quality attributes, suggesting that any drying air temperature can be used in the initial stages of drying as long as the product temperature does not exceed gelatinization temperature of matooke (72˚C). The optimum processing parameters for single-layer drying of matooke are: thickness = 3 mm, air temperatures 70˚C, dew point temperature 18˚C and air velocity 6 m/s overflow mode. From practical point of view it is recommended that for commercial processing of matooke, to employ multi-layer drying of loading capacity equal or less than 7 kg/m², thickness 3 mm, air temperatures 70˚C, dew point temperature 18˚C and air velocity 6 m/s overflow mode.

A pilot investigation of the relationship between climate variability and milk compounds under the bootstrap technique

This study analyzes the linear relationship between climate variables and milk components in Iran by applying bootstrapping to include and assess the uncertainty. The climate parameters, Temperature Humidity Index (THI) and Equivalent Temperature Index (ETI) are computed from the NASA-Modern Era Retrospective-Analysis for Research and Applications (NASA-MERRA) reanalysis (2002–2010). Milk data for fat, protein (measured on fresh matter bases), and milk yield are taken from 936,227 milk records for the same period, using cows fed by natural pasture from April to September. Confidence intervals for the regression model are calculated using the bootstrap technique. This method is applied to the original times series, generating statistically equivalent surrogate samples. As a result, despite the short time data and the related uncertainties, an interesting behavior of the relationships between milk compound and the climate parameters is visible. During spring only, a weak dependency of milk yield and climate variations is obvious, while fat and protein concentrations show reasonable correlations. In summer, milk yield shows a similar level of relationship with ETI, but not with temperature and THI. We suggest this methodology for studies in the field of the impacts of climate change and agriculture, also environment and food with short-term data.

Heat stress response for physiological traits in dairy and dual purpose cattle populations on phenotypic and genetic scales

The main objective of this thesis was to determine the potential impact of heat stress (HS) on physiological traits of lactating cows and semen quality of bulls kept in a temperate climate. The thesis is comprised of three studies. An innovative statistical modeling aspect common to all three studies was the application of random regression methodology (RRM) to study the phenotypic and genetic trajectory of traits in dependency of a continuous temperature humidity index (THI). In the first study, semen quality and quantity traits of 562 Holstein sires kept on an AI station in northwestern Germany were analyzed in the course of THI calculated from data obtained from the nearest weather station. Heat stress was identified based on a decline in semen quality and quantity parameters. The identified general HS threshold (THI = 60) and the thermoneutal zone (THI in the range from 50 to 60) for semen production were lower than detected in studies conducted in tropical and subtropical climates. Even though adult bulls were characterized by higher semen productivity compared to younger bulls, they responded with a stronger semen production loss during harsh environments. Heritabilities (low to moderate range) and additive genetic variances of semen characteristics varied with different levels of THI. Also, based on genetic correlations genotype, by environment interactions were detected. Taken together, these findings suggest the application of specific selection strategies for specific climate conditions. In the second study, the effect of the continuous environmental descriptor THI as measured inside the barns on rectal temperatures (RT), skin temperatures (ST), vaginal temperatures (VT), respiration rates (RR), and pulse rate (PR) of lactating Holstein Friesian (HF) and dual-purpose German black pied cattle (DSN) was analyzed. Increasing HS from THI 65 (threshold) to THI 86 (maximal THI) resulted in an increase of RT by 0.6 °C (DSN) and 1 °C (HF), ST by 3.5 °C (HF) and 8 °C (DSN), VT by 0.3 °C (DSN), and RR by 47 breaths / minute (DSN), and decreased PR by 7 beats / minute (DSN). The undesired effects of rising THI on physiological traits were most pronounced for cows with high levels of milk yield and milk constituents, cows in early days in milk and later parities, and during summer seasons in the year 2014. In the third study of this dissertation, the genetic components of the cow’s physiological responses to HS were investigated. Heat stress was deduced from indoor THI measurements, and physiological traits were recorded on native DSN cows and their genetically upgraded crosses with Holstein Friesian sires in two experimental herds from pasture-based production systems reflecting a harsh environment of the northern part of Germany. Although heritabilities were in a low range (from 0.018 to 0.072), alterations of heritabilities, repeatabilities, and genetic components in the course of THI justify the implementation of genetic evaluations including heat stress components. However, low repeatabilities indicate the necessity of using repeated records for measuring physiological traits in German cattle. Moderate EBV correlations between different trait combinations indicate the potential of selection for one trait to simultaneously improve the other physiological attributes. In conclusion, bulls of AI centers and lactating cows suffer from HS during more extreme weather conditions also in the temperate climate of Northern Germany. Monitoring physiological traits during warm and humid conditions could provide precious information for detection of appropriate times for implementation of cooling systems and changes in feeding and management strategies. Subsequently, the inclusion of these physiological traits with THI specific breeding values into overall breeding goals could contribute to improving cattle adaptability by selecting the optimal animal for extreme hot and humid conditions. Furthermore, the recording of meteorological data in close distance to the cow and visualizing the surface body temperature by infrared thermography techniques might be helpful for recognizing heat tolerance and adaptability in cattle.